PDA

Archiv verlassen und diese Seite im Standarddesign anzeigen : [topf] Bootschleife beim Topfield 7750 HDPVR mit HDMU_15148_E2_topf_217_git_4163_nodebug_mix



firemen79
30.06.2016, 18:23
Hallo,

wie hier heute schon mehrfach berichtet wurde kommt es mit dem neuen Image zu Reboot schleifen.
Habe für die Entwickler ein Serielles Log per Putty gemacht.


<<< Loader L23232>>>”ToFi"ZÀ‰ÀZ ò"ò8$bÿ¸¬
Ü ˜[!p


Board: TF7700 [29-bit mode]




U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043


DRAM: 128 MiB
NOR: 8 MiB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 1 0
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Can't read from device 0 **


** Unable to use usb 0:1 for fatload **
## Booting image at 85000000 ...
Bad Magic Number
## Booting image at 80060000 ...
Image Name: Linux-2.6.32.61_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1780727 Bytes = 1.7 MiB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK


Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:192.168.178.10:192.168.178.10:2 55.255.255.0:tf7700:eth0:off nwhwconf=device:eth0,hwaddr:00:3e:9e:11:22:33 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 - 0x00000000 - 0 ...




INIT: version 2.88 booting


init frontpanel
fsck.jfs version 1.1.15, 04-Mar-2011
processing started: 1/1/1970 1:00:00
The current device is: /dev/sda3
Block size in bytes: 4096
Filesystem size in blocks: 487785611
**Phase 0 - Replay Journal Log
Filesystem is clean.
[mountvirtfs] Mount /dev in tmpfs
[mountvirtfs] Copying device nodes to /dev
Starting portmap daemon....
Loading autofs
Starting autofs
[mountall] Mounting local filesystems...
Cleaning /tmp.
Hostname: TOPF.
init stmfb
LOADING MODULES
load firmware
copLoadFile (file /boot/audio.elf)
ustslave: Kernel Version: 24
base_address 0x10400000
seeking to 0
seeking to 5f00
seeking to 12320
seeking to 1aa20
seeking to 173100
seeking to 173138
seeking to 173170
seeking to 1b9058
seeking to 1b9060
seeking to 1b9068
seeking to 1b9070
seeking to 1d0920
seeking to 1d0a00
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x10000000
seeking to 0
seeking to 1277c0
seeking to 1277f8
seeking to 127830
seeking to 14d558
seeking to 14d564
seeking to 14d570
seeking to 17df30
seeking to 180000
init embx
init AVS
insmod: /lib/modules/smartcard.ko: module not found
showSinglePic /boot/bootlogo.mvi
Model: 'tf7700hdpvr'
vBoxType: 5
Input device name: "TDT RC event driver"
Selected Remote: Tf7700 RemoteControl
RemoteControl Map:
STANDBY - 0A - 116
MUTE - 0C - 113
ZOOM - 42 - 372
VMODE - 43 - 47
AUDIO - 08 - 392
0BUTTON - 10 - 11
1BUTTON - 11 - 2
2BUTTON - 12 - 3
3BUTTON - 13 - 4
4BUTTON - 14 - 5
5BUTTON - 15 - 6
6BUTTON - 16 - 7
7BUTTON - 17 - 8
8BUTTON - 18 - 9
9BUTTON - 19 - 10
BACK - 1E - 158
INFO - 1D - 358
SEARCH - 05 - 217
SUBTITLE - 07 - 370
TEXT - 47 - 388
DOWN/P- - 01 - 108
UP/P+ - 00 - 103
RIGHT/V+ - 02 - 106
LEFT/V- - 03 - 105
OK/LIST - 1F - 352
MENU - 1A - 139
GUIDE - 1B - 365
EXIT - 1C - 102
FAV - 09 - 364
RED - 4D - 398
GREEN - 0D - 399
YELLOW - 0E - 400
BLUE - 0F - 401
REWIND - 45 - 168
PAUSE - 06 - 119
PLAY - 46 - 207
FASTFORWARD - 48 - 208
RECORD - 4B - 167
STOP - 4A - 128
SLOWMOTION - 49 - 409
RECORDLIST - 51 - 395
SAT - 5E - 381
STEPBACK - 50 - 412
STEPFORWARD - 52 - 407
BOOKMARKS - 4C - 156
TV/RADIO - 04 - 378
MEDIA - 40 - 226
TIMER - 44 - 362
Frontpanel Map:
CHANNELDOWN - 02 - 109
CHANNELUP - 03 - 104
VOLUMEDOWN - 01 - 114
VOLUMEUP - 06 - 115
STANDBY - 0C - 116
Supports Long KeyPress: 1
processComplex >
period 110, delay 10
Using period=110 delay=10
VIDEO_SELECT_SOURCE MEMORY (Success)
VIDEO_PLAY (Success)
VIDEO_CONTINUE: (Success)
VIDEO_CLEAR_BUFFER: (Invalid argument)
[SEM] DOWN
[mountall] Mounting local filesystems...
Deconfiguring network interfaces... ifdown: interface lo not configured
ifdown: interface wlan0 not configured
done.
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... ip: RTNETLINK answers: File exists
udhcpc (v1.24.1) started
Sending discover...
Sending discover...
Sending select for 192.168.0.203...
Lease of 192.168.0.203 obtained, lease time 1814400
route: SIOCDELRT: No such process
adding dns 192.168.0.175
ip: SIOCGIFFLAGS: No such device
done.
starting e2->
[set_was_timer_wakeup] error reading /etc/enigma2/timers.xml
[set_was_timer_wakeup] no timer aktiv
Simple mixer control 'SPDIF',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 6 [60%] [on]
Simple mixer control 'Analog',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 6 [60%] [on]
Simple mixer control 'HDMI',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 6 [60%] [on]
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 3
ENIGMA2_DEBUG settings: Level=3
[MAIN] executing main
< 95.361> [HardwareInfo] Scanning hardware info
< 95.383> Detected: tf7700hdpvr
< 95.439> [Harddisk] enumerating block devices...
< 95.621> [Harddisk] new device sda -> /dev/sda -> /dev/sda
< 95.624> [ePopen] command: ('sdparm', 'sdparm', '--set=SCT=0', '/dev/sda')
< 95.640> [ePopen] command: ('sdparm', 'sdparm', '-C stop', '/dev/sda')
< 100.763> [SecConfigure] sec config cleared
< 100.774> [SecConfigure] slot: 0 configmode: simple
< 100.777> [SecConfigure] diseqcmode: single
< 100.781> [SecConfigure] slot: 1 configmode: simple
< 100.784> [SecConfigure] diseqcmode: diseqc_a_b
< 100.791> [SecConfigure] sec config completed
< 106.180> [ML] BlurayPlayer not installed: cannot import name BlurayPlayer
< 107.372> [InfoBar] Failed to load resumepoints: [Errno 2] No such file or directory: '/etc/enigma2/resumepoints.pkl'
libpng warning: iCCP: known incorrect sRGB profile
libpng warning: iCCP: cHRM chunk does not match sRGB
libpng warning: iCCP: known incorrect sRGB profile
libpng warning: iCCP: cHRM chunk does not match sRGB
< 111.393> [iInputDevices] getInputDevices mouse3 <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse3' >
< 111.396> [iInputDevices] getInputDevices event0 <ERROR: ioctl(EVIOCGNAME): [Errno 22] Invalid argument >
< 111.398> [iInputDevices] getInputDevices js2 <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js2' >
< 111.400> [iInputDevices] getInputDevices mouse2 <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse2' >
< 111.402> [iInputDevices] getInputDevices event1 <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/event1' >
< 111.404> [iInputDevices] getInputDevices js3 <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js3' >
< 111.405> [iInputDevices] getInputDevices js1 <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js1' >
< 111.408> [iInputDevices] getInputDevices js0 <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js0' >
< 111.409> [iInputDevices] getInputDevices event2 <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/event2' >
< 111.412> [iInputDevices] getInputDevices mouse0 <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse0' >
< 111.414> [iInputDevices] getInputDevices mice <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mice' >
< 111.416> [iInputDevices] getInputDevices event3 <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/event3' >
< 111.418> [iInputDevices] getInputDevices mouse1 <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse1' >
< 111.549> Selected keymap does not exist!
< 111.554> Activating language English
< 114.222> Traceback (most recent call last):
< 114.223> File "/usr/lib/enigma2/python/mytest.py", line 507, in <module>
< 114.230> keymapparser.readKeymap(config.usage.keymap.value)
< 114.232> File "usr/lib/enigma2/python/keymapparser.py", line 90, in readKeymap
< 114.237> keymapparser.KeymapError: [keymapparser] keymap /usr/local/share/enigma2/keymap.xml not well-formed.
e2 ended <- RTV: 0
*
starting e2->


INIT: Switching to runlevel: 6




INIT: Sending processes the TERM signal


Sending all processes the TERM signal...done.
Sending all processes the KILL signal...done.
Deactivating swap...umount: tmpfs busy - remounted read-only
done.
Unmounting local filesystems...umount: tmpfs busy - remounted read-only
done.
Rebooting...

flac
30.06.2016, 18:53
Danke,

Bug ist bekannt.


Siehe auch hier http://www.hdmedia-universe.com/board/showthread.php?10158-Bootschleife-bei-pingu-mit-HDMU-15148-enigma2-Git-4163&p=114698#post114698





Gruß

flac

- - - Aktualisiert - - -

Hab das Thema von Brotschleife in Bootschleife geändert.

santa
30.06.2016, 19:09
Mich hätte aber interessiert was eine brotschleife im Topf so alles zu Stande bringen kann.

firemen79
30.06.2016, 21:46
Kann ja nur nen schlechtes Brot gewesen sein.... So wie es gebacken wurde ;)

Joker7
30.06.2016, 22:00
Edit:

..gelöscht...wollte ich bei Spark Schreiben !

Drielander
01.07.2016, 13:21
Danke,

Bug ist bekannt.




Son Schiet - hätte ich besser vorher mal hier rein geschaut! :rolleyes:

Allso wieder mit Stick die vorherige Version flashen oder gibt es schon eine Lösung?

Gruß

santa
01.07.2016, 13:33
Siehe Spark Thread, Fehler in keymap.XML beseitigen

Drielander
01.07.2016, 13:56
Danke - aber da lass ich die Finger weg und warte lieber auf die korrigierte 15148.