SH4 - Stand der Dinge

[morly]

Hi Zusammen,
SH4 ist arg "schief" - werde darum den Sammelthread hier eröffnen und euch am Laufenden halten.
Antwortet hier im Thread um Bugs zu reporten.
Ich teste und arbeite mit meiner UFS 913!
Das nächste Image release ich, wenn ich es testfähig halte - nicht vorher!

Hi guys,
SH4 is kind of buggy ;) thereefor this thread to collect bugs and inform you about the current state of fixing...
Reply here to report your SH4 BUGS.
I test and develop with my ufs913
No release bofore I think it is worse a test...

Thx for you support!

Bugs:

Image bootet nicht (Dauerschleife) ... gefixt
StartWizard (Erstassi) erscheint nicht ... gefixt
OpenWebif funktioniert nicht .... gefixt
Permanente Untertitel ... gefixt
Falsche audio.elf bei IPBox ... gefixt
Leere "Information" ... gefixt
Fehler bei Standby ... gefixt
NetzwerkAssistent (Ethernet) ... gefixt
Overclock ... working
Kanalliste nach Installation ... gefixt
Plugins installieren ... gefixt
tiMote Screenshots ... gefixt
About Fenster ... added


Nach Image: HDMU_17212_E2_git_614

Bugs:

HDMU_17212_E2_1008g+se+_217_git_614 : falscher Kernel (uImage) ... gefixt
IPBoxen: Tuner 12V Bug ... gefixt (thx to ghani) ... gefixt
Falsche audio.elf bei IPBoxen ... gefixt
Menüeintrag: Project-ID version: enigma 2 (zweizeilig) ... gefixt
Fehlende Menüeinträge im Expertenmodus ... gefixt
audio.elf's aller Boxen anpassen ... gefixt
Crash beim SoftcamSetup ... gefixt
Crash bei Flashimage ... gefixt


Nach Image: HDMU_17313_E2_git_617

Bugs:

HDMU_17212_E2_1008g+se+_217_git_614 : Fehler im VideoWizard (Reboot) ...
Rote LED fehlt bei Aufnahme (UFS913) ...
ufs913: beim auswählen des streamings vom Handy aus(über timote 0.4.4) kommt es zu einem reboot
ErstAssi - Satellitenwahl - Reboot (konnte ich noch nicht nachstellen) ...
player 2 Bug ...
UFS912: ErstAssi startet nicht ...
...

[morly]

updated

[morly]

updated

[Alex23]

Hi,
danke morly, dass du dich um sh4 kümmerst.
Der Topf bleibt bei LOAD MODULES stehen.
Hier das log beim Startversuch:
ToFiÿ
<<< Loader L23231>>>
“ToFi"Z¿Š¿Z[!p

Board: TF7700 [29-bit mode]



U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043

DRAM: 128 MiB
NOR: 8 MiB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 1 0
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **
## Booting image at 85000000 ...
Bad Magic Number
## Booting image at 80060000 ...
Image Name: Linux-2.6.32.71_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1961528 Bytes = 1.9 MiB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:::255.255.255.0:tf7700:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:3e:9e:53:7d:9e - 0x00000000 - 0 ...


INIT: version 2.88 booting

init frontpanel
fsck.jfs version 1.1.15, 04-Mar-2011
processing started: 1/22/2018 15:43:12
The current device is: /dev/sda3

The superblock does not describe a correct jfs file system.

If device /dev/sda3 is valid and contains a jfs file system,
then both the primary and secondary superblocks are corrupt
and cannot be repaired, and fsck cannot continue.

Otherwise, make sure the entered device /dev/sda3 is correct.

[mountvirtfs] Mount /dev in tmpfs
[mountvirtfs] Copying device nodes to /dev
Starting portmap daemon....
Loading autofs
Starting autofs
[mountall] Mounting local filesystems...
Cleaning /tmp.
Hostname: TOPF.
init stmfb
LOADING MODULES
load firmware
copLoadFile (file /boot/audio.elf)
error ReadBytes
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x10000000
init embx


Hier noch das gesamte Log von der 2. Instalation bis Ende das Startvesuchs:
ToFiÿ <<< Loader L23231>>>
“ToFi"Z¿Š¿Z[!p


Board: TF7700 [29-bit mode]






U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043


DRAM: 128 MiB
NOR: 8 MiB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 1 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading uImage
.................................................. .................................................. .................................................. .................................................. .................................................. .................................................. .................................................. .................................................. ............






4224608 bytes read
## Booting image at 85000000 ...
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 4224544 Bytes = 4 MiB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK


Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:::255.255.255.0:tf7700:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:3e:9e:53:7d:9e - 0x00000000 - 0 ...


115200
speed 115200 baud;
intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>;
eol2 = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W;
lnext = ^V; flush = ^O; min = 1; time = 0;
-brkint ixoff -imaxbel
-------------------------------------
deploy.sh
V0.10: Try several times to mount USB sticks if mount fails
V0.09: Log installation to boot medium removed again because it caused problems
V0.08: Log installation to boot medium
V0.07: Do not install E2 if disk is not partitioned
and parameter partition is set to 0
V0.06: Added EXT2 option for E2 and MINI partitions
V0.05: Added JFS option for RECORD partition
V0.04: Changed ini File format
V0.03: Suppress meaningless tar errors during save settings
V0.02: Format Mini partitions with Ext3 instead of Ext2
V0.01: New parameter CREATEMINI and cleanup of KEEPSETTINGS
-------------------------------------
Mounting USB stick
Specification for KEEP SETTINGS detected at line 67
Specification for additional KEEP SETTINGS detected at line 88
-------------------------------------
partition: 0
createmini: 0
keepsettings: 0
keepbootargs: 1
usejfs: 1
useext2e2: 0
usbhdd: 0
format: 1
update: 1
-------------------------------------
Skipping partitioning of the disk
OK, Disk already partitioned.
Formatting HDD
mke2fs 1.41.14 (22-Dec-2010)
Filesystem label=MINI9
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
Stride=0 blocks, Stripe width=0 blocks
131648 inodes, 526128 blocks
26306 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=541065216
17 block groups
32768 blocks per group, 32768 fragments per group
7744 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912


Writing inode tables: 0/17 1/17 2/17 3/17 4/17 5/17 6/17 7/17 8/17 9/1710/1711/1712/1713/1714/1715/1716/17done
Creating journal (16384 blocks): done
Writing superblocks and filesystem accounting information: done


This filesystem will be automatically checked every 24 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
Setting up swapspace version 1, size = 271430144 bytes
8+0 records in
8+0 records out
Installing root file system
Flashing U-Boot settings
186+1 records in
186+1 records out
Skipped flashing mtdblock2 on user request.
Flashing kernel
3831+1 records in
3831+1 records out
e2fsck 1.41.14 (22-Dec-2010)
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
MINI9: 5312/131648 files (7.0% non-contiguous), 54498/526128 blocks
swapoff: /etc/fstab: No such file or directory


The system is going down NOW


Sending SIGTERM to all processe


Sending SIGKILL to all processe


Requesting system reboo
ToFiÿ
<<< Loader L23231>>>
“ToFi"Z¿Š¿Z[!p


Board: TF7700 [29-bit mode]






U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043


DRAM: 128 MiB
NOR: 8 MiB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 1 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading uImage




** Unable to read "uImage" from usb 0:1 **
## Booting image at 85000000 ...
Bad Magic Number
## Booting image at 80060000 ...
Image Name: Linux-2.6.32.71_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1961528 Bytes = 1.9 MiB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK


Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:::255.255.255.0:tf7700:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:3e:9e:53:7d:9e - 0x00000000 - 0 ...




INIT: version 2.88 booting


init frontpanel
skip
fsck.jfs version 1.1.15, 04-Mar-2011
processing started: 1/22/2018 15:52:13


Error: Cannot open device /dev/sda3


Usage: fsck.jfs [-afnpvV] [-j journal_device] [--omit_journal_replay] [--replay_journal_only] device


Emergency help:
-a Automatic repair.
-f Force check even if file system is marked clean.
-j journal_device Specify external journal device.
-n Check read only, make no changes to the file system.
-p Automatic repair.
-v Be verbose.
-V Print version information only.
--omit_journal_replay Omit transaction log replay.
--replay_journal_only Only replay the transaction log.
[mountvirtfs] Seems to be the first run - Making devices in /dev...
[makedev] Starting makedev...
CI-slot(s) : Yes
Tuners : 2
HDMI CEC : No
[makedev] done.
[mountvirtfs] Mount /dev in tmpfs
[mountvirtfs] Copying device nodes to /dev
Starting portmap daemon....
Loading autofs
Starting autofs
[mountall] Mounting local filesystems...
Cleaning /tmp /var/run /var/lock.
Hostname: TOPF.
init stmfb
LOADING MODULES
load firmware
copLoadFile (file /boot/audio.elf)
error ReadBytes

copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x10000000
init embx

[morly]

hast du ein altes image?
pack mal die alte audio.elf ins neue Image und teste nochmal

[Alex23]

Hab das mal probiert. Also mit 7zip einfach ins "rootfs.tar.gz\rootfs.tar\.\boot" rein kopiert. Danach hat 7zip neu gepackt. Ich hoffe das war so richtig.
Die ist von meinem Backup (14258). Die Größe hat sich aber bis hin zu den Letzten des Jahres 2017 nicht verändert.
Funktioniert hat das nicht:
ToFiÿ
<<< Loader L23231>>>
“ToFi"Z¿Š¿Z[!p

Board: TF7700 [29-bit mode]



U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043

DRAM: 128 MiB
NOR: 8 MiB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 1 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading uImage
.................................................. .................................................. .................................................. .................................................. .................................................. .................................................. .................................................. .................................................. ............



4224608 bytes read
## Booting image at 85000000 ...
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 4224544 Bytes = 4 MiB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:::255.255.255.0:tf7700:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:3e:9e:53:7d:9e - 0x00000000 - 0 ...

115200
speed 115200 baud;
intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>;
eol2 = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W;
lnext = ^V; flush = ^O; min = 1; time = 0;
-brkint ixoff -imaxbel
-------------------------------------
deploy.sh
V0.10: Try several times to mount USB sticks if mount fails
V0.09: Log installation to boot medium removed again because it caused problems
V0.08: Log installation to boot medium
V0.07: Do not install E2 if disk is not partitioned
and parameter partition is set to 0
V0.06: Added EXT2 option for E2 and MINI partitions
V0.05: Added JFS option for RECORD partition
V0.04: Changed ini File format
V0.03: Suppress meaningless tar errors during save settings
V0.02: Format Mini partitions with Ext3 instead of Ext2
V0.01: New parameter CREATEMINI and cleanup of KEEPSETTINGS
-------------------------------------
Mounting USB stick
Specification for KEEP SETTINGS detected at line 67
Specification for additional KEEP SETTINGS detected at line 88
-------------------------------------
partition: 0
createmini: 0
keepsettings: 0
keepbootargs: 1
usejfs: 1
useext2e2: 0
usbhdd: 0
format: 1
update: 1
-------------------------------------
Skipping partitioning of the disk
OK, Disk already partitioned.
Formatting HDD
mke2fs 1.41.14 (22-Dec-2010)
Filesystem label=MINI9
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
Stride=0 blocks, Stripe width=0 blocks
131648 inodes, 526128 blocks
26306 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=541065216
17 block groups
32768 blocks per group, 32768 fragments per group
7744 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912

Writing inode tables: 0/17 1/17 2/17 3/17 4/17 5/17 6/17 7/17 8/17 9/1710/1711/1712/1713/1714/1715/1716/17done
Creating journal (16384 blocks): done
Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 38 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
Setting up swapspace version 1, size = 271430144 bytes
8+0 records in
8+0 records out
Installing root file system
tar: invalid tar header checksum
Flashing U-Boot settings
186+1 records in
186+1 records out
Skipped flashing mtdblock2 on user request.
Flashing kernel
3831+1 records in
3831+1 records out
e2fsck 1.41.14 (22-Dec-2010)
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
MINI9: 697/131648 files (7.5% non-contiguous), 30982/526128 blocks
swapoff: /etc/fstab: No such file or directory

The system is going down NOW

Sending SIGTERM to all processe

Sending SIGKILL to all processe

Requesting system reboo
ToFiÿ
<<< Loader L23231>>>
“ToFi"Z¿Š¿Z[!p

Board: TF7700 [29-bit mode]


U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043

DRAM: 128 MiB
NOR: 8 MiB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 1 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading uImage


** Unable to read "uImage" from usb 0:1 **
## Booting image at 85000000 ...
Bad Magic Number
## Booting image at 80060000 ...
Image Name: Linux-2.6.32.71_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1961528 Bytes = 1.9 MiB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:::255.255.255.0:tf7700:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:3e:9e:53:7d:9e - 0x00000000 - 0 ...


INIT: version 2.88 booting

init frontpanel
fsck.jfs: error while loading shared libraries: libuuid.so.1: cannot open shared object file: No such file or directory
[mountvirtfs] Seems to be the first run - Making devices in /dev...
[makedev] Starting makedev...
CI-slot(s) : Yes
Tuners : 2
HDMI CEC : No
[makedev] done.
[mountvirtfs] Mount /dev in tmpfs
[mountvirtfs] Copying device nodes to /dev
Starting portmap daemon....
Loading autofs
Starting autofs
/etc/init.d/autofs: line 56: /usr/sbin/automount: not found
/etc/init.d/autofs: line 56: /usr/sbin/automount: not found
[mountall] Mounting local filesystems...
mkdir: can't create directory '/var/lock': No such file or directory
mkdir: can't create directory '/var/lock/subsys': No such file or directory
mkdir: can't create directory '/var/log': No such file or directory
mkdir: can't create directory '/var/lib': No such file or directory
mkdir: can't create directory '/var/lib/urandom': No such file or directory
mkdir: can't create directory '/var/run': No such file or directory
ln: /var/tmp: No such file or directory
Cleaning /tmp.
Hostname: TOPF.
init stmfb
Segmentation fault
LOADING MODULES
load firmware
copLoadFile (file /boot/audio.elf)
ustslave: Kernel Version: 24
base_address 0x10400000
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x10000000
init embx
init AVS
insmod: can't insert '/lib/modules/p2div64.ko': invalid module format
insmod: can't insert '/lib/modules/pseudocard.ko': unknown symbol in module, or unknown parameter
insmod: can't insert '/lib/modules/stm_monitor.ko': unknown symbol in module, or unknown parameter
insmod: can't insert '/lib/modules/stmdvb.ko': unknown symbol in module, or unknown parameter
insmod: can't insert '/lib/modules/player2.ko': unknown symbol in module, or unknown parameter
insmod: can't insert '/lib/modules/sth264pp.ko': unknown symbol in module, or unknown parameter
insmod: can't insert '/lib/modules/stmalloc.ko': unknown symbol in module, or unknown parameter
insmod: can't insert '/lib/modules/platform.ko': invalid module format
insmod: /lib/modules/smartcard.ko: module not found
cat: write error: Input/output error
/etc/init.d/rcS: line 667: /usr/sbin/inetd: not found
showSinglePic /boot/bootlogo.mvi
VIDEO_SET_FORMAT failed (Bad file descriptor)
[mountall] Mounting local filesystems...
Deconfiguring network interfaces... ifdown: interface lo not configured
ifdown: interface eth0 not configured
ifdown: interface eth1 not configured
ifdown: interface wlan0 not configured
done.
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... ip: RTNETLINK answers: File exists
ifup: can't open '/var/run/ifstate.new': No such file or directory
done.
mkdir: can't create directory '/var/lock': No such file or directory
mkdir: can't create directory '/var/lock/subsys': No such file or directory
mkdir: can't create directory '/var/log': No such file or directory
mkdir: can't create directory '/var/lib': No such file or directory
mkdir: can't create directory '/var/lib/urandom': No such file or directory
mkdir: can't create directory '/var/run': No such file or directory
ln: /var/tmp: No such file or directory
Cleaning.
/usr/bin/amixer: error while loading shared libraries: libasound.so.2: cannot open shared object file: No such file or directory
/etc/init.d/rcS: line 667: /usr/sbin/mount.sh: not found
/usr/bin/amixer: error while loading shared libraries: libasound.so.2: cannot open shared object file: No such file or directory
/usr/bin/amixer: error while loading shared libraries: libasound.so.2: cannot open shared object file: No such file or directory
[set_was_timer_wakeup] error reading /etc/enigma2/timers.xml
[set_was_timer_wakeup] no timer aktiv
starting e2->
/etc/init.d/rcS: line 667: /usr/local/bin/enigma2: not found
e2 ended <- RTV: 127
*

INIT: Switching to runlevel: 6starting e2->



INIT: Sending processes the TERM signal

Sending all processes the TERM signal...done.
Sending all processes the KILL signal...done.
Deactivating swap...umount: tmpfs busy - remounted read-only
done.
Unmounting local filesystems...umount: tmpfs busy - remounted read-only
done.
Rebooting... ToFiÿ
<<< Loader L23231>>>
“ToFi"Z¿Š¿Z[!p

Board: TF7700 [29-bit mode]



U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043

DRAM: 128 MiB
NOR: 8 MiB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 1 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading uImage


** Unable to read "uImage" from usb 0:1 **
## Booting image at 85000000 ...
Bad Magic Number
## Booting image at 80060000 ...
Image Name: Linux-2.6.32.71_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1961528 Bytes = 1.9 MiB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:::255.255.255.0:tf7700:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:3e:9e:53:7d:9e - 0x00000000 - 0 ...


INIT: version 2.88 booting

init frontpanel
fsck.jfs: error while loading shared libraries: libuuid.so.1: cannot open shared object file: No such file or directory
[mountvirtfs] Mount /dev in tmpfs
[mountvirtfs] Copying device nodes to /dev
Starting portmap daemon....
Loading autofs
Starting autofs
/etc/init.d/autofs: line 56: /usr/sbin/automount: not found
/etc/init.d/autofs: line 56: /usr/sbin/automount: not found
[mountall] Mounting local filesystems...
mkdir: can't create directory '/var/lock': No such file or directory
mkdir: can't create directory '/var/lock/subsys': No such file or directory
mkdir: can't create directory '/var/log': No such file or directory
mkdir: can't create directory '/var/lib': No such file or directory
mkdir: can't create directory '/var/lib/urandom': No such file or directory
mkdir: can't create directory '/var/run': No such file or directory
ln: /var/tmp: No such file or directory
Cleaning /tmp.
Hostname: TOPF.
init stmfb
Segmentation fault
LOADING MODULES
load firmware
copLoadFile (file /boot/audio.elf)
ustslave: Kernel Version: 24
base_address 0x10400000
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x10000000
init embx
init AVS
insmod: can't insert '/lib/modules/p2div64.ko': invalid module format
insmod: can't insert '/lib/modules/pseudocard.ko': unknown symbol in module, or unknown parameter
insmod: can't insert '/lib/modules/stm_monitor.ko': unknown symbol in module, or unknown parameter

[Alex23]

Hi,
bei der Triplex fehlt der Eintrag "SoftCam / CI" unter Einstellungen im Menü.
Unter System fehlen:
- "A/V-Einstellungen"
- "Fernbedienung-Einstellungen"
- "Skin"
- "Testbilder"

Wenn man versucht per Admintool drauf zuzugreifen, friert das Bild ein und nur Strom aus hilft weiter.
Falls hierzu ein Log gewünscht wird, bitte ich um Nachricht, da ich für das serielle Log etwas Aufwand bei der Box habe.

[morly]

updated

[biomus]

@morly, was war eigentlich mit der Tuner los, also der 12V Bug. Gab dieseer Fehler immer 'Tune failed'? Wenn so, ist das auch bei der Spark behoben?

[morly]

genauen Fehler kenn ich nicht, findest die Infos im letzten ipbox Thread

Fix war nur für ipbox & co

[biomus]

Wäre wohl schön zu wissen. Mein Spark hat immer diesen Fehler. Kann ja auch elektronisch sein, Brauch ich das Teil nicht auf zu schrauben :rolleyes: . Habe gestern schon mein Fernseher repariert. Eine reicht! Demnächst kann ich auch wieder testen. Habe mein Netzwerk wieder im griff. Scheiß Quallcom/Atheros WiFi!
.

[FrankBB2702]

Also ich habe jetzt das Image 17311 auf der einen UFS913 auf der anderen ist noch 16594. Bisher läuft alles sehr gut. Im Menü ist noch eine Doppelzeile. Ich konnte bisher nur einen Tunnig -Fehler feststellen jedoch nur bei einem Sender. Ich denke daher, dass es eine falsche Einstellung bei mir ist - der Fehler ist nur bei ZDF-neo HD. Danke

[technomate]

Hello ,Thanks for last image 17313 ,tried in IPBOX910 .
What I cannot see is the menu for setting up the record path .
In the past images we had the chance to set up the path ,currently not .
Can you improve this ?
Thanks .

[mumbi]

Also ich habe jetzt das Image 17311 auf der einen UFS913 [...] Im Menü ist noch eine Doppelzeile.

Die Doppelzeile ist bei der 17313 weg.

[morly]

Hello ,Thanks for last image 17313 ,tried in IPBOX910 .
What I cannot see is the menu for setting up the record path .
In the past images we had the chance to set up the path ,currently not .
Can you improve this ?
Thanks .

did u switch to expert settings (menu)?

[zakn]

Hi Morly, very nice to contact you regarding your ingenuity for development of apps.

I have a receiver called Truman it is Spark sti7162 sh4.
When I connect LAN cable and USB wifi stick the WiFi shows green, however, does not pickup IP
and I will have a network connection. When I remove the cable the network does not work!
I configured the wlan to rt5370sta. Why the test of USB WiFi stick shows that the driver is rt2870?
If I try wlan rt2870 it does not recognize the WiFi. Thank you for your assistance.

The following are the specs and output from Telnet:

Description: 802.11n Wireless LAN Card (Ralink 802.11n WLAN)
Device Type: Vendor Specific
Protocal Version: USB 2.00
Current Speed: High Speed
Max Current: 450mA
USB Device ID: VID = 148F PID = 5370
Serial Number: 1.0
Device Vendor: Ralink
Device Name: 802.11n WLAN
Device Revision: 0101
Controller Vendor: Ralink
Controller Part Number: RT5370

cat / proc / bus / usb / devices :

T: Bus = 04 Lev = 00 Prnt = 00 Port = 00 Cnt = 00 Dev # = 1 Spd = 12 MxCh = 1
B: Alloc = 0/900 us (0%), # Int = 0, # Iso = 0
D: Ver = 1.10 Cls = 09 (hub) Sub = 00 Prot = 00 MxPS = 64 # Cfgs = 1
P: Vendor = 1d6b ProdID = 0001 Rev = 2.06
S: Manufacturer = Linux 2.6.32.71_stm24_0217 ohci_hcd
S: Product = STMicroelectronics OHCI Host Controller
S: SerialNumber = stm-ohci.1
C: * # Ifs = 1 Cfg # = 1 Atr = e0 MxPwr = 0mA
I: * If # = 0 Alt = 0 # EPs = 1 Cls = 09 (hub) Sub = 00 Prot = 00 Driver = stroke
E: Ad = 81 (I) Atr = 03 (Int.) MxPS = 2 Ivl = 255ms

T: Bus = 03 Lev = 00 Prnt = 00 Port = 00 Cnt = 00 Dev # = 1 Spd = 480 MxCh = 1
B: Alloc = 0 / 800 μs (0%), # Int = 0, # Iso = 0
D: Ver = 2.00 Cls = 09 (hub) Sub = 00 Prot = 00 MxPS = 64 # Cfgs = 1
P: Vendor = 1d6b ProdID = 0002 Rev = 2.06
S: Manufacturer = Linux 2.6.32.71_stm24_0217 ehci_hcd
S: Product = STMicroelectronics EHCI Host Controller
S: SerialNumber = stm-ehci.1
C: * # Ifs = 1 Cfg # = 1 Atr = e0 MxPwr = 0mA
I: * If # = 0 Alt = 0 # EPs = 1 Cls = 09 (hub) Sub = 00 Prot = 00 Driver = Stroke
E: Ad = 81 (I) Atr = 03 (Int.) MxPS = 4 Ivl = 256ms

T: Bus = 03 Lev = 01 Prnt = 01 Port = 00 Cnt = 01 Dev # = 2 Spd = 480 MxCh = 0
D: Ver = 2.00 Cls = 00 (> ifc) Sub = 00 Prot = 00 MxPS = 64 # Cfgs = 1
P: Vendor = abcd ProdID = 1234 Rev = 1.00
S: Manufacturer = General
S: Product =
S: SerialNumber = Р ‰
C: * # Ifs = 1 Cfg # = 1 Atr = 80 MxPwr = 100mA
I: * If # = 0 Alt = 0 # EPs = 2 Cls = 08 (stor.) Sub = 06 Prot = 50 Driver = usb-storage
E: Ad = 01 (O) Atr = 02 (Bulk) MxPS = 512 Ivl = 0ms
E: Ad = 81 (I) Atr = 02 (bulk) MxPS = 512 Ivl = 0ms

T: Bus = 02 Lev = 00 Prnt = 00 port = 00 Cnt = 00 Dev # = 1 Spd = 12 MxCh = 1
B: Alloc = 0/900 μs (0%), # Int = 0, # Iso = 0
D : Ver = 1.10 Cls = 09 (hub) Sub = 00 Prot = 00 MxPS = 64 # Cfgs = 1
P: Vendor = 1d6b ProdID = 0001 Rev = 2.06
S: Manufacturer = Linux 2.6.32.71_stm24_0217 ohci_hcd
S: Product = STMicroelectronics OHCI Host Controller
S: SerialNumber = stm-ohci.0
C: * # Ifs = 1 Cfg # = 1 Atr = e0 MxPwr = 0mA
I: * If # = 0 Alt = 0 # EPs = 1 Cls = 09 (hub) Sub = 00 Prot = 00 Driver = stroke
E: Ad = 81 (I) Atr = 03 (Int.) MxPS = 2 Ivl = 255ms

T: Bus = 01 Lev = 00 Prnt = 00 Port = 00 Cnt = 00 Dev # = 1 Spd = 480 MxCh = 1
B: Alloc = 0/800 μs (0%), # Int = 0, # Iso = 0
D: Ver = 2.00 Cls = 09 (hub) Sub = 00 Prot = 00 MxPS = 64 # Cfgs = 1
P: Vendor = 1d6b ProdID = 0002 Rev = 2.06
S: Manufacturer = Linux 2.6.32.71_stm24_0217 ehci_hcd
S: Product = STMicroelectronics EHCI Host Controller
S: SerialNumber = stm-ehci.0
C: * #Ifs = 1 Cfg # = 1 Atr = e0 MxPwr = 0mA
I: * If # = 0 Alt = 0 # EPs = 1 Cls = 09 (hub) Sub = 00 Prot = 00 Driver = stroke
E: Ad = 81 (I) Atr = 03 (Int.) MxPS = 4 Ivl = 256ms

T: Bus = 01 Lev = 01 Prnt = 01 Port = 00 Cnt = 01 Dev # = 2 Spd = 480 MxCh = 0
D: Ver = 2.00 Cls = 00 (> ifc) Sub = 00 Prot = 00 MxPS = 64 #Cfgs = 1
P: Vendor = 148f ProdID = 5370 Rev = 1.01
S: Manufacturer = Ralink
S: Product =
802.11n WLAN S: SerialNumber = 1.0
C: * # Ifs = 1 Cfg # = 1 Atr = 80 MxPwr = 450mA
I: * If # = 0 Alt = 0 # EPs = 7 Cls = ff (vend.) Sub = ff Prot = ff Driver = rt2870
E: Ad = 81 (I) Atr = 02 (Bulk) MxPS = 512 Ivl = 0ms
E: Ad = 01 (O) Atr = 02 (Bulk) MxPS = 512 Ivl = 0ms
E: Ad = 02 (O) Atr = 02 (Bulk) MxPS = 512 Ivl = 0ms
E: Ad = 03 (O) Atr = 02 (Bulk) MxPS = 512 Ivl = 0ms
E: Ad = 04 (O) Atr = 02 (Bulk) MxPS = 512 Ivl = 0ms
E: Ad = 05 (O) Atr = 02 (Bulk) MxPS = 512 Ivl = 0ms
E: Ad = 06 (O) Atr = 02 (Bulk) MxPS = 512 Ivl = 0ms
lsusb:
Bus 001 Device 001: ID 1d6b: 0002
Bus 002 Device 001: ID 1d6b: 0001
Bus 003 Device 001: ID 1d6b: 0002
Bus 004 Device 001: ID 1d6b: 0001
Bus 001 Device 002: ID 148f: 5370
Bus 003 Device 004: ID abcd: 1234