Archiv verlassen und diese Seite im Standarddesign anzeigen : HDMU_1233_E2_ipbox900_209_git_4781_nodebug_nolcd_D iff3_ffm_USB.tar.gz
hi
this is my 1st visit im not sure if i am posting in the right place and i dont speak german so please bear with me.
i have installed the image on my 900hd ipbox on a 16gb usb stick and i am finding my way through it.
i dont have a great knowledge of e2 but can load images and ftp etc.
i was trying to install neutrino keymap for ipbox 900 from the plugins menu but i cant find where to install it.
it tells me that is is downloaded ok but i cannot find it.
also i have an external e-sata hdd connected but i am not sure how to get this working.
the hdd info only reads the usb stick
if anyone could help on these 2 problems i would be greatful
thanks
h
If you install the neutrino keymap, you have only to reboot the box.
After that, you can switch the programs with up/down without using the channellist.
Your HDD must have the label RECORD, formated in ext(2,3 or4) and there a directory movie.
If you don't know how, please post the output of these in telnet:
blkid
fdisk -l
thanks for the reply santa
i can see the channels change up/down but i had thought the plugin was a function to modify the behaviour of the buttons as in other images, i.e green button assigned to stop/start emu etc, but maybe that is somewhere else or not part of this image yet?
the telnet output reads
BusyBox v1.20.2 (2012-10-13 08:45:32 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
IPBOX900:~# blkid
/dev/sda1: LABEL="ext2" UUID="bcbd209f-c621-4ec1-9ffc-54b29a6d64e7" TYPE="ext2"
IPBOX900:~# fdisk -l
Disk /dev/sda: 16.0 GB, 16008609792 bytes
255 heads, 63 sectors/track, 1946 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 1947 15633392 c Win95 FAT32 (LBA)
IPBOX900:~#
which to me says it is reading the usb stick
i have an e-sata hdd which i wanted to use for recordings but maybe ths is not possible and as i say i have a limited knowledge.
thanks
h
ps sorry 1 other quick question - does the scart out work at the same time as hdim output as i want to send picture to 2nd tv.
Oh, images with the p209 kernel don't find sata hdds.
You need to install a p211 image, but this isn't in git a this time.
You can try to install an ipbox910 image, then post the output here, if this image will boot.
Emu you can only start/stop in hdmu center, softcam.
Hdmi and scary isn't really possible.
Only if you use 576p in Hdmi, but who wants that.
Jule_666
04.11.2012, 11:16
Vielleicht kann bpanther p211 ja noch für die 900er und 91 basteln. Läuft mit der 910 perfekt und die 9000er ja anscheinend auch...
das habe ich ihn vor längeren schonmal gefragt, hat er noch nicht geschafft, werde ihn aber nochmal damit nerven.
sorry guys Ich spreche kein Deutsch.
sorry i didnt mean in any way to be rude guys
Sorry, but we only talk about how to fix your problem.
Have you try to install an ip910 image?
yes im sorry i have install neutrinino 910 image and it booted ok but i couldnt get it to read disecq config for the 2 sats that i have 19.2e & 28.2e.
i was then going to try HDMU 910 image but i cannot get the usb stick formatted.
byy the way i forgot to mention that i have a 500gb usb hdd - is there any way i can use this to run the image and act as pvr hdd?
thx
h
usb hdd isn´t a problem.
if you boot a flash image, you must format your stick with,
mkfs.ext2 -I 128 -b 4096 /dev/sda1
with fdisk /dev/sda
you have the possible to create more partitions, so you can faster and easier test images.
with p211 images, your sata drive must work.
thanks santa but i dont have a clue about partitions etc.
i cant get my usb stick to work now here is the output from telnet
[SifTeam]$ cd /tmp
[SifTeam]$ mount #
rootfs on / type rootfs (rw)
/dev/root on / type squashfs (ro)
none on /tmp type tmpfs (rw)
none on /dev type tmpfs (rw)
none on /mnt type tmpfs (rw)
/dev/mtdblock4 on /var type jffs2 (rw)
none on /tmp/mqueue type mqueue (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
tmpfs on /dev/shm type tmpfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
[SifTeam]$ umount /dev/sda1
umount: can't umount /dev/sda1: Invalid argument
[SifTeam]$
ps i have dgs image
in flash and it is stable and is good as a fallback up to experimenting with e2/neutrino images
Danke schön
ok, let´s try to create partitions.
download this tool: here (http://www.hdmedia-universe.com/board/showthread.php?1044-Partinionieren-von-HDD-und-USB-Sticks&p=12717&viewfull=1#post12717)
stick into your pc, start create mini
choose your stick, format
boot dgs and mount and install images to sda2, sda3 or sda4.
if you want to install later a new one, format the part with:
mkfs.ext2 -I 128 -b 4096 -L MINI2 /dev/sda2
maybe you have to change your bootargs:
fw_setenv menu_1 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:2 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda2 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA2-USB;boot'fw_setenv menu_2 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:3 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda3 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA3-USB;boot'
fw_setenv menu_3 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:4 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda4 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA4-USB;boot'
fw_setenv menu_4 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:2 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sdb2 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDB2-USB;boot'
fw_setenv menu_5 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:3 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sdb3 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDB3-USB;boot'
fw_setenv menu_6 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:4 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sdb4 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDB4-USB;boot'
then you have press 1 to get image from sda2
2-->sda3
3-->sda4
later if you test with sata drive, you have to press:
4-->sda2
5-->sda3
6-->sda4
hi
i cant get the partition tool to see the usb stick
i have tried re-booting my pc and used another stick but the dropdown list is always blank.
i can see and access both sticks in windows explorer tree
h
there is no option to run as administrator wnen right clicking on the createmini.exe file.
i am logged in with an administrator account.
h
then you must create it with telnet:
fdisk /dev/sda
d for delete, enter
n for new
p for primary
1 first part
1 first cylinder
500 last cylinder
n
p
2
enter
1000
n
p
3
enter
1500
n
p
4
enter
enter
w to write table to disk and exit
then:
mkfs.ext2 -I 128 -b 4096 -L MINI2 /dev/sda2
mkfs.ext2 -I 128 -b 4096 -L MINI3 /dev/sda3
mkfs.ext2 -I 128 -b 4096 -L MINI4 /dev/sda4
mount and install image.
when you have start an hdmu image, then:
mkswap -L SWAPPART /dev/sda1
ok thanks santa sorry for being so slow i have partititioned the stick as per your instruction ( i think) but am stuck at the mkfs stage.
i get the following with telnet
[SifTeam]$ mkfs.ext2 -I 128 -b 4096 -L MINI2 /dev/sda2
mke2fs 1.38 (30-Jun-2005)
mkfs.ext2: /dev/sda2 is mounted !
mkfs.ext2: it's not safe to run badblocks!
[SifTeam]$
tried that i get
[SifTeam]$ umount /dev/sda2
umount: can't umount /mnt/usb: Device or resource busy
[SifTeam]$
[SifTeam]$ mount
rootfs on / type rootfs (rw)
/dev/root on / type squashfs (ro)
none on /tmp type tmpfs (rw)
none on /dev type tmpfs (rw)
none on /mnt type tmpfs (rw)
/dev/mtdblock4 on /var type jffs2 (rw)
none on /tmp/mqueue type mqueue (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
tmpfs on /dev/shm type tmpfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
/dev/sda2 on /mnt/usb type ext2 (rw)
/dev/sda1 on /mnt/usb/usb0 type msdos (rw,sync,fmask=0022,dmask=0022,codepage=cp437)
/dev/sda3 on /mnt/usb/usb2 type ext2 (rw,sync)
/dev/sda4 on /mnt/usb/usb3 type ext2 (rw,sync)
[SifTeam]$ blkid
/dev/sda4: LABEL="MINI4" UUID="2a3fc62b-bdb4-4a85-8e4a-8e04eb65dc5a" TYPE="ext2"
/dev/sda3: LABEL="MINI3" UUID="16ca575a-5874-4fcd-add6-a47ac7c5199a" TYPE="ext2"
/dev/sda2: LABEL="MINI2" UUID="06057718-480f-4f41-8da7-e5c7009b3306" TYPE="ext2"
/dev/sda1: UUID="6004-2803" TYPE="vfat"
[SifTeam]$
install your image to /mnt/usb/usb3
so it is on sda4.
then try to boot from it.
im not sure how to install image to a separate partition.
previously i was using this guide to install images to single partition. i tried and it tarred the image to mnt/usb/usb3 but it wouldnt boot.
cd /tmp
mount # you will see mounted usb dev/sda1 or sdb1
umount /dev/sda1
mkfs.ext2 /dev/sda1 -L ext2
mount /dev/sda1 /mnt/usb #if you see mounted usb0 than mount /dev/sda1 /mnt/usb/usb0
#with ftp put your E2 in mnt/usb or mnt/usb/usb0
cd /mnt/usb # or cd /mnt/usb/usb0
ls -aln
tar xzvf yourE2.tar.gz
sync
sync
mkfs.ext2 -I128 -b4096 -L MINI1 /dev/sda1
use this
im sorry for being a real newbie but i cant get the image to boot from the partitioned stick.
i have used mkfs.ext2 -I128 -b4096 -L MINI1 /dev/sda1
and was able to install the image to /mnt/usb.
the message i get on screen is 'e2-sda1-usb' but does not boot
i also tried boot from sda2, sda3 & sda4.
when i reboot from dgs flash i can see in ftp the image is installed in /mnt/usb/usb0 so i dont know where i went wrong.
h
do you have the external SATA on your Box?
If yes, you have to boot from sdb1-USB
try to make a serial log.
i dont have the external sata connected just usb stick
try to make a serial log?
please post:
fw_printenv
baudrate=115200
menu_timeout=echo booting...;front_puts "booting";boot
menu_serialbreak=echo entering boot loader console.;front_puts "console"
menu_upgusb=setenv stdout vga;setenv stderr vga;if usbupg; then reset; else echo
Oops...; echo You can debug through serial port.; fi
menu_upgserial=setenv stdout vga;setenv stderr vga;serial_upgrade;reset
menu_set2set=setenv stdout vga;setenv stderr vga;serial_set2set;reset
menu_hddfmt=setenv bootargs $bootargs format_hdd=1;front_puts "format hdd";boot
menu_debugmode=setenv bootargs $bootargs debug debug_app=1;front_puts "debug shell";boo
t
menu_upgnet=setenv bootargs $bootargs factory_update=1;front_puts "net upg";boot
menu_tvmode=set_tvmode;boot
serial#=cuberevo debugging
board=relook511s_27
monitor_base=0xA0000000
monitor_len=0x00040000
monitor_sec=1:0
load_addr=0x84000000
unprot=protect off $monitor_sec
update=erase $monitor_sec;cp.b $load_addr $monitor_base $monitor_len;protect on
$monitor_sec
nfsroot=/home/ipbox/rootfs
boothdd=run bootargshdd;ide reset;ext2load ide 0:5 a5ff0000 boot/uImage;bootm a5ff0000
bootide=run bootargside;ide reset;ext2load ide 0:5 a5ff0000 boot/uImage;bootm a5
ff0000
preboot=if edb toenv ethaddr; then echo "Setup mac address."; else echo "Use def
ault mac address."; fi; bootmenu
menu_upgusbhost=setenv stdout vga;setenv stderr vga;if usbupghost; then reset; e
lse echo Oops...; echo You can debug through serial port.; fi
menu_0=front_puts "SET0-CRI-FLASH";setenv bootargs "console=ttyAS1,115200 panic=
3 root=/dev/mtdblock3 bigphysarea=1500 ip=$ipaddr:$serverip:$gateway:$netmask quiet";setenv bootcmd "fro
nt_puts CRI-FLASH; bootm a0060000";saveenv;boot
menu_1=front_puts "SET1-CRI-SDA1-USB";setenv bootusb "run bootargsusb;usb reset;
ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs panic=3 console=ttyAS1,115200 bigphys
area=1500 rootdelay=10 root=/dev/sda1 rw rootdelay=10 quiet";setenv bootcmd "fro
nt_puts CRI-SDA1-USB; run bootusb";saveenv;boot
menu_2=front_puts "SET2-CRI-SDA2-USB";setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:2 a5ff0000 boot/uImage;bootm a5f
f0000";setenv bootargsusb "setenv bootargs panic=3 console=ttyAS1,115200 bigphys
area=1500 rootdelay=10 root=/dev/sda2 rw rootdelay=10 quiet";setenv bootcmd "fro
nt_puts CRI-SDA2-USB; run bootusb";saveenv;boot
menu_9=front_puts "SET9-CRI-SDA4-USB";setenv bootusb "run bootargsusb;usb reset;
ext2load usb 0:4 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv
bootargs panic=3 console=ttyAS1,115200 bigphysarea=1500 rootdelay=10 root=/dev/sda4 rw rootdelay=10 quiet";setenv bootcmd "front_puts CRI-SDA4
-USB; run bootusb";saveenv;boot
menu_3=front_puts "SET3-CRI-SDA3-USB";setenv bootusb "run bootargsusb;usb reset;
ext2load usb 0:3 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs panic=3 console=ttyAS1,115200 bigphysarea=1500 rootde
lay=10 root=/dev/sda3 rw rootdelay=10 quiet";setenv bootcmd "front_puts CRI-SDA3
-USB; run bootusb";saveenv;boot
bootargshdd=setenv bootargs printk=1 console=ttyAS1,115200 panic=3 root=/dev/sda5 rw rootdelay=10 init=/bin/devinit ip=192.168.1.8:192.168.1.1:
192.168.1.1:255.255.255.0 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000
bootargside=setenv bootargs printk=1 console=ttyAS1,115200 panic=3 root=/dev/sda
5 rw rootdelay=10 init=/bin/devinit mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000
menu_4=front_puts "SET4-E2-FLASH";setenv bootargs "printk=1 console=ttyAS1,11520
0 panic=3 root=/dev/mtdblock3 rw mem=128m coprocessor_mem=4m@0x10000000,4m@0x104
00000";setenv bootcmd "front_puts E2-FLASH; bootm a0060000";saveenv;boot
menu_6=front_puts "SET6-E2-SDA2-USB";setenv bootusb "run bootargsusb;usb reset;e
xt2load usb 0:2 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv
bootargs printk=1 console=ttyAS1,115200 panic=3 root=/dev/sda2 rw rootdelay=10 init=/bin/devinit ip=$ipaddr:$serverip:$gatew
ay:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000";setenv bootcmd
"front_puts E2-SDA2-USB; run bootusb";saveenv;boot
menu_7=front_puts "SET7-E2-SDA3-USB";setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:3 a5ff0000 boot/uImage;bootm
a5ff0000";setenv bootargsusb "setenv bootargs printk=1 console=ttyAS1,115200 pan
ic=3 root=/dev/sda3 rw rootdelay=10 init=/bin/devinit ip=$ipaddr:$serverip:$gate
way:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000";setenv bootcmd "front_puts E2
-SDA3-USB; run bootusb";saveenv;boot
menu_5=front_puts "SET5-E2-SDA1-USB";setenv bootusb "run bootargsusb;usb reset;e
xt2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs printk=1 console=ttyAS1,115200 panic=3 root=/dev/
sda1 rw rootdelay=10 init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask me
m=128m coprocessor_mem=4m@0x10000000,4m@0x10400000";setenv bootcmd "front_puts E
2-SDA1-USB; run bootusb";saveenv;boot
menu_8=front_puts "SET8-E2-SDA4-USB";setenv bootusb "run bootargsusb;usb reset;e
xt2load usb 0:4 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv
bootargs printk=1 console=ttyAS1,115200 panic=3 root=/dev/sda4 rw rootdelay=10 init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask mem=128m coproces
sor_mem=4m@0x10000000,4m@0x10400000";setenv bootcmd "front_puts E2-SDA4-USB; run
bootusb";saveenv;boot
bootusb=run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000
bootargsusb=setenv bootargs printk=1 console=ttyAS1,115200 panic=3 root=/dev/sda
1 rw rootdelay=10 init=/bin/devinit ip=::: mem=128m coprocessor_mem=4m@0x1000000
0,4m@0x10400000
stdin=serial
stdout=serial
stderr=serial
ethaddr=00:13:18:02:6C:25
bootargs=console=ttyAS1,115200 panic=3 root=/dev/mtdblock3 bigphysarea=1500 ip=:
:: quiet
bootcmd=front_puts CRI-FLASH; bootm a0060000
[SifTeam]$
ok, you have install to sda1, and you have try boot with button 5?
still no luck loading from sda1.
i have tried several times.
the multiboot option is definitely no.5
i have the following partitions set up
mount
rootfs on / type rootfs (rw)
/dev/root on / type squashfs (ro)
none on /tmp type tmpfs (rw)
none on /dev type tmpfs (rw)
none on /mnt type tmpfs (rw)
/dev/mtdblock4 on /var type jffs2 (rw)
none on /tmp/mqueue type mqueue (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
tmpfs on /dev/shm type tmpfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
/dev/sda2 on /mnt/usb type ext2 (rw)
/dev/sda1 on /mnt/usb/usb0 type ext2 (rw,sync)
/dev/sda2 on /mnt/usb/usb1 type ext2 (rw)
/dev/sda3 on /mnt/usb/usb2 type ext2 (rw,sync)
[SifTeam]$
i have installed the image on mnt/usb/usb0 and can see all the image files when viewing from ftp
i just cant get the e2 image to boot.
it looks like i will just have to stick to 1 image on the stick
h
try to make a serial log.
ok i found a serial lead and tried to boot twice from sda1 then loaded from flash .
here is the logfile from putty
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
that´s the problem, i think.
try this:
fw_setenv menu_1 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda1 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA1-USB;boot'
fw_setenv menu_2 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 1:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda1 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA1-USB;boot'
then, boot with 1 or 2, please a with serial log again.
still wont boot from 1 or 2 front panel says 'sda1 usb' each time
here is log
Bad Magic Number
this is the problem if you format the part with mkfs.ext2 /dev/sda1 withou -I128...
please try to umount and format new
umount /dev/sda1
mkfs.ext2 -L MINI1 -I128 -b4096 /dev/sda1
mount /dev/sda1 ...
ftp
cd /mnt...
tar xvzf HDMU*.tar.gz
ok i have tried that and still wont boot from sda1 it just keeps trying.
i dont know what is wrong
thx
h
ok,the stick is now ok, the kernel was load and started, but not the image, please try this bootarg.
fw_setenv menu_1 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sdb1 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDB1-USB;boot'
the last test was button 1?
I have changed the code above then try to boot from 2 = sda1 usb then 1= sdb1 usb then 5 = e2 sda1 usb but still the same.
i tried several times deleting and re-partitioning the usb and tried another usb but no luck
h
which image do you try to install?
I see only a P207 Image, try an other Image, p209 for IP900 or p211 for IP910
I have been able to load pkt e2 p211 image I will get it set up then I assume I can install 2 other images to usb1 & usb2 to see which one I like best I would like to get my external e-data hdd working if possible along with scart had. I may be able to use my 500gb usb drive to be partitioned for images and recordings?
Thanks for the help
H
yes, my images are installed on my sata hdd.
ok sorry to be a nuisance but i think my best option is to partition my 500gb usb hdd and use it to have several images on and also act as a hdd for recordings.
i am having a bit of trouble formatting it maybe you could give me these steps then i should be able to partition and load images as before on 16gb usb stick.
this is the mount info
SifTeam]$ mount
rootfs on / type rootfs (rw)
/dev/root on / type squashfs (ro)
none on /tmp type tmpfs (rw)
none on /dev type tmpfs (rw)
none on /mnt type tmpfs (rw)
/dev/mtdblock4 on /var type jffs2 (rw)
none on /tmp/mqueue type mqueue (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
tmpfs on /dev/shm type tmpfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
/dev/sda2 on /var/media type ext3 (rw,data=writeback)
[SifTeam]$
thanks
h
Disk /dev/sda: 500.0 GB, 500074283008 bytes
255 heads, 63 sectors/track, 60797 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 32 257008+ 83 Linux
/dev/sda2 33 60797 488094862+ 83 Linux
[SifTeam]$
fdisk /dev/sda
delete 2
delete 1
n for create new part,
p primary
1
start 1
stop 60647
n
p
2
enter
60697
n
p
3
enter
60747
n
p
4
enter
enter
w write to exit
reboot
mkfs.ext2 -L RECORD /dev/sda1
mkfs.ext2 -L MINI2 -I128 -b4096 /dev/sda2
mkfs.ext2 -L MINI3 -I128 -b4096 /dev/sda3
mkfs.ext2 -L MINI4 -I128 -b4096 /dev/sda4
reboot
ftp image to one MINI Part(2,3 or4)
cd /mnt...
tar xvzf *.*
fw_setenv menu_1 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:2 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda2 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA2-USB;boot'
fw_setenv menu_2 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:3 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda3 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA3-USB;boot'
fw_setenv menu_3 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:4 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda4 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA4-USB;boot'
Last cylinder or +size or +sizeM or +sizeK (1-60797, default 60797):
here you have to fill in 60647
im having trouble getting the device to write the new allocation table.
after following all the steps is says error 16 the device or resource is busy and on reboot the new partitions are not set?
Last cylinder or +size or +sizeM or +sizeK (1-60797, default 60797):
here you have to fill in 60647
sorry i realised that mistake and edited the post
this f*** image!
put this stick in your pc and format.
so your box doesn´t mount it.
you can also test to unmount with:
umount /dev/sda2
im sorry friend it sounds like you are a bit upset. i would understand this as i have probably taken up too much of your time
i tried to format the stick in pc but it isnt allocated a drive letter but shows in device manager as working ok
it´s ok, i'am happy if it´s works.
please try it again.
post
mount
blkid
if you don´t can unmount
ive got this
rootfs on / type rootfs (rw)
/dev/root on / type squashfs (ro)
none on /tmp type tmpfs (rw)
none on /dev type tmpfs (rw)
none on /mnt type tmpfs (rw)
/dev/mtdblock4 on /var type jffs2 (rw)
none on /tmp/mqueue type mqueue (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
tmpfs on /dev/shm type tmpfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
/dev/sda2 on /var/media type ext2 (rw)
[SifTeam]$ blkid
/dev/sda4: LABEL="MINI4" UUID="e8499ac6-ecb5-4846-95fd-206af403d56c" TYPE="ext2"
/dev/sda3: LABEL="MINI3" UUID="639814e2-fab5-4cb2-b516-3bf306cd00e7" TYPE="ext2"
/dev/sda2: LABEL="MINI2" UUID="2c2a4b66-e650-4975-bec6-3835d69cfea9" TYPE="ext2"
/dev/sda1: LABEL="RECORD" UUID="4743f7ed-93ce-42bd-915f-3db1be5c613c" TYPE="ext2"
[SifTeam]$
but i cant see the partitions in /mnt/usb when i connect to ftp
if i disconnect and re-connect the drive then re-connect it then connect to ftp i see usb0,usb1,usb2,usb3 in /mnt/usb
then i get this from telnet
rootfs on / type rootfs (rw)
/dev/root on / type squashfs (ro)
none on /tmp type tmpfs (rw)
none on /dev type tmpfs (rw)
none on /mnt type tmpfs (rw)
/dev/mtdblock4 on /var type jffs2 (rw)
none on /tmp/mqueue type mqueue (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
tmpfs on /dev/shm type tmpfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
/dev/sda2 on /var/media type ext2 (rw)
/dev/sdb1 on /mnt/usb/usb0 type ext2 (rw,sync)
/dev/sdb2 on /mnt/usb/usb1 type ext2 (rw,sync)
/dev/sdb3 on /mnt/usb/usb2 type ext2 (rw,sync)
/dev/sdb4 on /mnt/usb/usb3 type ext2 (rw,sync)
[SifTeam]$ blkid
/dev/sdb4: LABEL="MINI4" UUID="e8499ac6-ecb5-4846-95fd-206af403d56c" TYPE="ext2"
/dev/sdb3: LABEL="MINI3" UUID="639814e2-fab5-4cb2-b516-3bf306cd00e7" TYPE="ext2"
/dev/sdb2: LABEL="MINI2" UUID="2c2a4b66-e650-4975-bec6-3835d69cfea9" TYPE="ext2"
/dev/sdb1: LABEL="RECORD" UUID="4743f7ed-93ce-42bd-915f-3db1be5c613c" TYPE="ext2"
i dont know where it is going wrong it sounds like the drive isnt being detected at boot but then adds it as second drive (sdb) when disconnecting and re-connecting after the box has booted
i could ftp to sdb2,3 & 4 but dont have the boot options to start from them.
sorry again for burdening you with this and thank you for your patience
h
try the bootargs from sda, log
the problem seems to be that the disk isnt being mounted in /mnt/usb upon reboot.
when it is disconnected and re-connected it appears as
/dev/sdb1 on /mnt/usb/usb0 type ext2 (rw,sync)
/dev/sdb2 on /mnt/usb/usb1 type ext2 (rw,sync)
/dev/sdb3 on /mnt/usb/usb2 type ext2 (rw,sync)
/dev/sdb4 on /mnt/usb/usb3 type ext2 (rw,sync)
i think the partitions are fine as per this readout from disk utility tool.
here is also serial bootlog
thanks
h22592258
i think i am sorted now
i booted the box without usb so it wasnt being seen as sda2.
when i then connected it it was correctly recognised as sda1,sda2,sda3 &sda4 in mnt/usb/usb0, mnt/usb/usb1,mnt/usb/usb2 & mnt/usb/usb3.
i then installed
pkt svn 1843 to sda2
bpanther neutrino 4536 to sda3
hdmu 1233 to sda4
so i am now goint to see which one is best foe epg and recording function and also which has option for scart out to 2nd tv
many thanks to santa for helping me get this far
h
Powered by vBulletin® Version 4.2.5 Copyright ©2024 Adduco Digital e.K. und vBulletin Solutions, Inc. Alle Rechte vorbehalten.