perryair
05.09.2013, 19:33
Moin Moin,
was mach ich denn flasch beim loggen komme immer nur bis dahin dann kommt nix mehr :(
Hab das jetzt mit Morlys Tool gemacht nach Anleitung aus dem Forum bricht aber nach dem Boot leider ab...
#Log file from Morlys SH4 STB Admin Tool from: Do Sep 5 2013, 19:26:11
Board: STx7105-PDK [32-bit mode]
U-Boot 1.3.1 (Jun 19 2012 - 17:10:44) - stm23_0051 - YW_1.1.005 overclock
DRAM: 256 MiB
Panel: VFD
NAND: Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
512 MiB
SPI: info: found S25FL016K (2MiB) device (page=256,erase=65536)
warning: SPI device may be write-protected (status=0x9c)
In: serial
Out: serial
Err: serial
Ident ic exist
Ident ic get stb id
IdentID : 0c 00 07 00 00 32 45
Hit ESC to stop autoboot: 3 2 1 0
Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
Image Name: Linux-2.6.32.59_stm24_0211
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2534827 Bytes = 2.4 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.59_stm24_0211
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2534827 Bytes = 2.4 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
stmac_phy_get_addr(): id1 = 0xffff, id2 = 0xffff
found phy at addres = 2
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = c07003245
Starting kernel console=ttyAS1,115200 rw root=/dev/mtdblock6 rootfstype=jffs2 init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 ip=172.100.100.249:172.100.100.174:172.100.100.174 :255.255.0.0:Enigma2:eth0:off stmmaceth=msglvl:0,phyaddr:2,watchdog:5000 bigphysarea=6000 nwhwconf=device:eth0,hwaddr:30:00:07:00:32:45 Manufacture=Spark-Project STB_ID=0C:00:07:00:00:32:45 - 0x00000000 - 0 ...
Enigma2 Log
#Log file from Morlys SH4 STB Admin Tool from: Do Sep 5 2013, 20:22:25
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
STMFB accel interface available
+ (9) GFBDC
15360k total video mem
7260k usable video mem
5640kB available for acceleration surfaces.
resolution: 720 x 576 x 32 (stride: 2880)
+ (9) gLCDDC
eDBoxLCD::eDBoxLCD >
Error loading config file!
LCD resolution: -1 x -1 x -727913224 (stride: 1701601889)
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "fulan front panel buttons" is a remotecontrol
Input device "TDT RC event driver" is a remotecontrol
failed to open /dev/input/event2
Input device "" is a keyboard
failed to open /dev/input/event3
Input device "" is a remotecontrol
Found 4 input devices.
+ (22) Hdmi CEC driver
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
done, found 0 common interface slots
+ (35) CA handler
+ (36) Stream server
[SERVERSOCKET] ERROR on bind() (Address already in use)
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryDVD
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
---- opening lame channel db
reading services (version 4)
loaded 6963 services
scanning for frontends..
opening frontend 0
close frontend 0
opening frontend 1
close frontend 1
opening frontend 2
close frontend 2
found 1 adapter, 3 frontends(3 sim) and 4 demux, boxtype 29
Use valid Linux Time :) (RTC?)
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
Loading spinners...
[ePNG] couldn't open /usr/local/share/enigma2/skin_default/spinner/wait13.png
found 12 spinner!
executing main
setIoPrio best-effort level 3 ok
main thread is non-idle! display spinner!
Failed to open /dev/dbox/fp0
[Harddisk] enumerating block devices...
new Harddisk sda -> /dev/sda -> /dev/sda
Reading satellites.xml
Reading cables.xml
sec config cleared
setSlotInfo for dvb frontend 0 to slotid 0, descr Tuner3-C(T/C), need rotorworkaround No, enabled No, DVB-S2 No
setSlotInfo for dvb frontend 1 to slotid 1, descr Tuner1-Sat, need rotorworkaround No, enabled Yes, DVB-S2 Yes
setSlotInfo for dvb frontend 2 to slotid 2, descr Tuner2-Sat, need rotorworkaround No, enabled No, DVB-S2 Yes
slot: 1 configmode: advanced
add 192 to 6
slot: 2 configmode: nothing
sec config completed
loading bouquet... /etc/enigma2/bouquets.tv 1
loading bouquet... /etc/enigma2/userbouquet.mein_tv.tv 1
45 entries in Bouquet userbouquet.mein_tv.tv
loading bouquet... /etc/enigma2/userbouquet.hdtv_sky_hd.tv 46
34 entries in Bouquet userbouquet.hdtv_sky_hd.tv
loading bouquet... /etc/enigma2/userbouquet.sky_hdtv.tv 80
24 entries in Bouquet userbouquet.sky_hdtv.tv
loading bouquet... /etc/enigma2/userbouquet.sky_cinema.tv 104
10 entries in Bouquet userbouquet.sky_cinema.tv
loading bouquet... /etc/enigma2/userbouquet.sky__welt___extra.tv 114
37 entries in Bouquet userbouquet.sky__welt___extra.tv
loading bouquet... /etc/enigma2/userbouquet.sky_sport.tv 151
32 entries in Bouquet userbouquet.sky_sport.tv
loading bouquet... /etc/enigma2/userbouquet.austriasat.tv 183
13 entries in Bouquet userbouquet.austriasat.tv
loading bouquet... /etc/enigma2/userbouquet.kinder.tv 196
12 entries in Bouquet userbouquet.kinder.tv
loading bouquet... /etc/enigma2/userbouquet.musik.tv 208
16 entries in Bouquet userbouquet.musik.tv
loading bouquet... /etc/enigma2/userbouquet.oesterreich.tv 224
26 entries in Bouquet userbouquet.oesterreich.tv
loading bouquet... /etc/enigma2/userbouquet.schweiz.tv 250
14 entries in Bouquet userbouquet.schweiz.tv
loading bouquet... /etc/enigma2/userbouquet.italia_tv.tv 264
89 entries in Bouquet userbouquet.italia_tv.tv
loading bouquet... /etc/enigma2/userbouquet.holland.tv 353
23 entries in Bouquet userbouquet.holland.tv
loading bouquet... /etc/enigma2/userbouquet.sky_select.tv 376
14 entries in Bouquet userbouquet.sky_select.tv
loading bouquet... /etc/enigma2/userbouquet.xxx.tv 390
47 entries in Bouquet userbouquet.xxx.tv
loading bouquet... /etc/enigma2/userbouquet.favourites.tv 437
0 entries in Bouquet userbouquet.favourites.tv
loading bouquet... /etc/enigma2/userbouquet.LastScanned.tv 437
1621 entries in Bouquet userbouquet.LastScanned.tv
17 entries in Bouquet bouquets.tv
loading bouquet... /etc/enigma2/bouquets.radio 1
loading bouquet... /etc/enigma2/userbouquet.deutsche.radio 1
19 entries in Bouquet userbouquet.deutsche.radio
loading bouquet... /etc/enigma2/userbouquet.favourites.radio 20
0 entries in Bouquet userbouquet.favourites.radio
2 entries in Bouquet bouquets.radio
[FONT] adding font /usr/local/share/fonts/nmsbd.ttf...OK (Regular)
[FONT] adding font /usr/local/share/fonts/andale.ttf...OK (Fixed)
[FONT] adding font /usr/local/share/fonts/goodtime.ttf...OK (Crs)
[FONT] adding font /usr/local/share/fonts/age.ttf...OK (Age)
[FONT] adding font /usr/local/share/fonts/tuxtxt.ttf...OK (Console)
[FONT] adding font /usr/local/share/fonts/time.ttf...OK (BMCTime)
[FONT] adding font /usr/local/share/fonts/ae_AlMateen.ttf...OK (Replacement)
3660kB available for acceleration surfaces.
resolution: 1280 x 720 x 32 (stride: 5120)
[FONT] adding font /usr/share/fonts/md_khmurabi_10.ttf...OK (Regular)
[FONT] adding font /usr/share/fonts/valis_lcd.ttf...OK (Digital)
[FONT] adding font /usr/local/share/fonts/valis_enigma.ttf...OK (Subs)
[FONT] adding font /usr/local/share/fonts/nmsbd.ttf...OK (FdLcD)
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse3' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse2' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse1' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse0' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/event3' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/event2' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 22] Invalid argument >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 22] Invalid argument >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 25] Inappropriate ioctl for device >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js3' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js2' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js1' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js0' >
Selected keymap does not exist!
Activating language Deutsch
[ePopen] command: ip -o addr show dev eth0
eDBoxLCD::getInstance
loadSkin: Screen already defined elsewhere: HDMU_MainMenu
loadSkin: Screen already defined elsewhere: HDMU_SoftcamControl
loadSkin: Screen already defined elsewhere: HDMU_OverclockControl
loadSkin: Screen already defined elsewhere: HDMU_SystemControl
loadSkin: Screen already defined elsewhere: HDMU_SystemInfos
loadSkin: Screen already defined elsewhere: HDMU_ufsup
loadSkin: Screen already defined elsewhere: HDMU_OSDControl
loadSkin: Screen already defined elsewhere: HDMU_VFDControl
loadSkin: Screen already defined elsewhere: HDMU_VideoControl
loadSkin: Screen already defined elsewhere: HDMU_DLNAServer
loadSkin: Screen already defined elsewhere: HDMU_OpenVPN
loadSkin: Screen already defined elsewhere: HDMU_SkinControl
[WebInterface] set language to de
[WebInterface] set language to de
[WebInterface] fallback to default translation for Webinterface
[WebInterface] fallback to default translation for Configuration for the Webinterface
[eSocketMMIHandler] created successfully
getModeList for port Component
getModeList for port Scart
getModeList for port HDMI
getModeList for port HDMI-PC
hotplug on dvi
-> setting aspect, policy, policy2, wss any bestfit policy auto
-> setting aspect, policy, policy2, wss any bestfit policy auto
-> setting aspect, policy, policy2, wss any bestfit policy auto
-> setting aspect, policy, policy2, wss any bestfit policy auto
setMode - port: HDMI mode: 1080p rate: 50Hz
-> setting aspect, policy, policy2, wss any bestfit policy auto
updateColor: HDMI
LINE # automatically generated by enigma 2
LINE
[AutoMount.py] self.automounts without mounts {}
[NetworkBrowser] fallback to default translation for NetworkBrowser
[NetworkBrowser] fallback to default translation for Search for network shares
[NetworkBrowser] fallback to default translation for MountManager
[NetworkBrowser] fallback to default translation for Manage network shares
starting hotplug handler
adding Resource DiseqcTester
resources: {'DiseqcTester': <function DiseqcTesterMain at 0x15d7064>}
[Toplevel.importExternalModules] Imported external module: Example
[HTTPRootResource}.__init__
[Webinterface] started on 0.0.0.0:80 auth=False ssl=False
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[HTTPRootResource}.__init__
[Webinterface] started on 0.0.0.0:443 auth=True ssl=True
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[EPGC] setCacheFile read/write epg data from/to '/hdd/epg.dat'
[EPGC] time updated.. start EPG Mainloop
[SKIN] Parsing embedded skin <embedded-in-'Screensaver'>
[EPGC] 6631 events read from /hdd/epg.dat
[Skin] Attribute not implemented: scrollbarMode value: showOnDemand
warning, skin is missing element boquet in <class 'Screens.ChannelSelection.ChannelSelection'>
fp_control: SW Version 1.03
Model: spark7162
vBoxType: 11
Selected Model: Edision Spark frontpanel control utility
Spark_init
checkConfig
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S
, WAKEUPDECREMENT 300
18
warning, skin is missing element RassLogo in <class 'Screens.RdsDisplay.RdsInfoDisplay'>
[SKIN] No skin to read...
warning, skin is missing element UnhandledKeyPixmap in <class 'Screens.UnhandledKey.UnhandledKey'>
warning, skin is missing element From in <class 'Screens.Dish.Dish'>
warning, skin is missing element Goto in <class 'Screens.Dish.Dish'>
warning, skin is missing element posGoto in <class 'Screens.Dish.Dish'>
warning, skin is missing element posFrom in <class 'Screens.Dish.Dish'>
warning, skin is missing element turnTime in <class 'Screens.Dish.Dish'>
RemovePopup, id = ZapError
setValue 50
Setvolume: 50 50 (raw)
Setvolume: 32 32 (-1db)
playing 1:0:1:6DCA:44D:1:C00000:0:0:0:
[__evStart]
[__evSeekableStatusChanged]
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
RemovePopup, id = ZapError
allocate channel.. 044d:0001
opening frontend 1
(1)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 0 Freq 11836500 Pol 0 SR 27500000 INV 2 FEC 3 orbpos 192 system 0 modulation 1 pilot 2, rolloff 0
tuning to 1236 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:1:6DCA:44D:1:C00000:0:0:0:
allocate demux
child has terminated
pipes closed
[ePopen] command: route -n | grep eth0
poll: unhandled POLLERR/HUP/NVAL for fd 30(16)
set sequence pos 3
set sequence pos 4
[SEC] setVoltage 2
[SEC] sleep 200ms
child has terminated
pipes closed
192.168
0.0.0.0
nameservers: [[192, 168, 10, 1]]
read configured interface: {'lo': {'dhcp': False}, 'wlan0': {'dhcp': True}, 'eth0': {'dhcp': True}}
self.ifaces after loading: {'eth0': {'preup': False, 'predown': False, 'ip': [192, 168, 10, 34], 'up': True, 'mac': '30:00:07:00:32:45', 'dhcp': True, 'bcast': [192, 168, 10, 255], 'netmask': [255, 255, 255, 0], 'gateway': [192, 168, 10, 1]}}
poll: unhandled POLLERR/HUP/NVAL for fd 37(16)
[SEC] invalidate current switch params
[SEC] sendDiseqc: e00000(DiSEqC reset)
[SEC] sleep 50ms
[SEC] sendDiseqc: e00003(DiSEqC peripherial power on)
[SEC] sleep 150ms
[SEC] sendDiseqc: e01039f5(?)
[SEC] sleep 50ms
set sequence pos 3
[SEC] setTone 1
[SEC] sleep 10ms
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 1
(1)fe event: status 0, inversion off, m_tuning 1
[SEC] sleep 500ms
(1)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x194a8d8 running
[eEPGCache] channel 0x194a8d8 running
[EPGC] next update in 2 sec
stop release channel timer
ok ... now we start!!
eventNewProgramInfo 0 0
have 1 video stream(s) (0065), and 1 audio stream(s) (0066), and the pcr pid is 0065, and the text pid is 0068
allocate demux
TuxTxt cache cleared
decoder state: play, vpid=101, apid=102
DMX_SET_PES_FILTER(0x65) - pcr - ok
DMX_SET_PES_FILTER(0x66) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 0 - ok
DMX_SET_PES_FILTER(0x65) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x68) - ttx - ok
TuxTxt cache cleared
TuxTxt: initialized
TuxTxt service started 68
TuxTxt running thread...(068)
VIDEO_CONTINUE - ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
AUDIO_CHANNEL_SELECT(0) - ok
disable teletext subtitles
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Das Erste
[showCrypted]
[showDolby]
[showMp3]
[eDVBCAService] new service 1:0:1:6DCA:44D:1:C00000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:1:6DCA:44D:1:C00000:0:0:0:
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
RemovePopup, id = ZapError
PATready
use pmtpid 0064 for service_id 6dca
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
eventNewProgramInfo 0 0
have 1 video stream(s) (0065), and 3 audio stream(s) (0066, 0067, 006a), and the pcr pid is 0065, and the text pid is 0068
decoder state: play, vpid=101, apid=102
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Das Erste
[showCrypted]
[showDolby]
[showMp3]
[eDVBCIInterfaces] gotPMT
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 5
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Das Erste
[showCrypted]
[showDolby]
[showMp3]
[__evUpdatedEventInfo]
[EPGC] start caching events(1378405216)
[eDVBLocalTimerHandler] diff is 0
[eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
[eDVBLocalTimerHandler] not changed
AITready
sdt update done!
[EPGC] abort non avail schedule other reading
[EPGC] abort non avail netmed schedule reading
[EPGC] abort non avail netmed schedule other reading
[EPGC] abort non avail FreeSat schedule_other reading
[EPGC] abort non avail viasat reading
OCready
[EPGC] nownext finished(1378405224)
[EPGC] schedule finished(1378405245)
[EPGC] stop caching events(1378405245)
[EPGC] next update in 60 min
not enough diskspace for timeshift! (less than 200MB)
warning, skin is missing element FullDescription in <class 'Screens.EventView.EventViewEPGSelect'>
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 12
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 12
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - failed (Value too large for defined data type)
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 12
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 12
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 12
not enough diskspace for timeshift! (less than 200MB)
not enough diskspace for timeshift! (less than 200MB)
playing 1:0:1:6D66:437:1:C00000:0:0:0:
[eDVBCAService] free slot 0 demux 0 for service 1:0:1:6DCA:44D:1:C00000:0:0:0:
[eDVBCAService] free service 1:0:1:6DCA:44D:1:C00000:0:0:0:
decoder state: play, vpid=-1, apid=-1
DEMUX_STOP - pcr - ok
DEMUX_STOP - video - ok
VIDEO_STOP - ok
AUDIO_STOP - ok
DEMUX_STOP - audio - ok
AUDIO_CONTINUE - ok
DEMUX_STOP - ttx - ok
TuxTxt stopped service 68
cleaning up
TuxTxt cache cleared
start release channel timer
[__evStart]
[__evSeekableStatusChanged]
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
RemovePopup, id = ZapError
[eDVBLocalTimerHandler] remove channel 0x194a8d8
[eEPGCache] remove channel 0x194a8d8
allocate channel.. 0437:0001
(1)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 0 Freq 11953500 Pol 0 SR 27500000 INV 2 FEC 3 orbpos 192 system 0 modulation 1 pilot 2, rolloff 0
tuning to 1353 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:1:6D66:437:1:C00000:0:0:0:
allocate demux
set sequence pos 3
set sequence pos 3
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 1
(1)fe event: status 0, inversion off, m_tuning 1
(1)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x19d8470 running
[eEPGCache] channel 0x19d8470 running
[EPGC] next update in 2 sec
stop release channel timer
ok ... now we start!!
eventNewProgramInfo 0 0
have 1 video stream(s) (006e), and 1 audio stream(s) (0078), and the pcr pid is 006e, and the text pid is 0082
allocate demux
TuxTxt cache cleared
decoder state: play, vpid=110, apid=120
DMX_SET_PES_FILTER(0x6e) - pcr - ok
DMX_SET_PES_FILTER(0x78) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 0 - ok
DMX_SET_PES_FILTER(0x6e) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x82) - ttx - ok
TuxTxt cache cleared
TuxTxt: initialized
TuxTxt service started 82
TuxTxt running thread...(082)
VIDEO_CONTINUE - ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
disable teletext subtitles
[__evUpdatedInfo]
[writeChannelName]
vfd display text: ZDF
[showCrypted]
[showDolby]
[showMp3]
[eDVBCAService] new service 1:0:1:6D66:437:1:C00000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:1:6D66:437:1:C00000:0:0:0:
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
RemovePopup, id = ZapError
[SEC] sleep 500ms
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
[__evUpdatedInfo]
[writeChannelName]
vfd display text: ZDF
[showCrypted]
[showDolby]
[showMp3]
PATready
use pmtpid 0064 for service_id 6d66
eventNewProgramInfo 0 0
have 1 video stream(s) (006e), and 4 audio stream(s) (0078, 0079, 007a, 007d), and the pcr pid is 006e, and the text pid is 0082
decoder state: play, vpid=110, apid=120
[__evUpdatedInfo]
[writeChannelName]
vfd display text: ZDF
[showCrypted]
[showDolby]
[showMp3]
[eDVBCIInterfaces] gotPMT
sdt update done!
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 5
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
[__evUpdatedEventInfo]
AITready
[EPGC] start caching events(1378405289)
not enough diskspace for timeshift! (less than 200MB)
playing 1:0:1:6DCA:44D:1:C00000:0:0:0:
[eDVBCAService] free slot 0 demux 0 for service 1:0:1:6D66:437:1:C00000:0:0:0:
[eDVBCAService] free service 1:0:1:6D66:437:1:C00000:0:0:0:
decoder state: play, vpid=-1, apid=-1
DEMUX_STOP - pcr - ok
DEMUX_STOP - video - ok
VIDEO_STOP - ok
AUDIO_STOP - ok
DEMUX_STOP - audio - ok
AUDIO_CONTINUE - ok
DEMUX_STOP - ttx - ok
TuxTxt stopped service 82
cleaning up
TuxTxt cache cleared
start release channel timer
[__evStart]
[__evSeekableStatusChanged]
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
RemovePopup, id = ZapError
[eDVBLocalTimerHandler] remove channel 0x19d8470
[eEPGCache] remove channel 0x19d8470
[EPGC] abort caching events !!
allocate channel.. 044d:0001
(1)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 0 Freq 11836500 Pol 0 SR 27500000 INV 2 FEC 3 orbpos 192 system 0 modulation 1 pilot 2, rolloff 0
tuning to 1236 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:1:6DCA:44D:1:C00000:0:0:0:
allocate demux
set sequence pos 3
set sequence pos 3
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 1
(1)fe event: status 0, inversion off, m_tuning 1
(1)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x19d8470 running
[eEPGCache] channel 0x19d8470 running
[EPGC] next update in 59 min
stop release channel timer
ok ... now we start!!
eventNewProgramInfo 0 0
have 1 video stream(s) (0065), and 1 audio stream(s) (0066), and the pcr pid is 0065, and the text pid is 0068
allocate demux
TuxTxt cache cleared
decoder state: play, vpid=101, apid=102
DMX_SET_PES_FILTER(0x65) - pcr - ok
DMX_SET_PES_FILTER(0x66) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 0 - ok
DMX_SET_PES_FILTER(0x65) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x68) - ttx - ok
TuxTxt cache cleared
TuxTxt: initialized
TuxTxt service started 68
VIDEO_CONTINUE - TuxTxt running thread...(068)
ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
disable teletext subtitles
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Das Erste
[showCrypted]
[showDolby]
[showMp3]
[eDVBCAService] new service 1:0:1:6DCA:44D:1:C00000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:1:6DCA:44D:1:C00000:0:0:0:
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
RemovePopup, id = ZapError
[SEC] sleep 500ms
[eDVBLocalTimerHandler] diff is -1
[eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
[eDVBLocalTimerHandler] update RTC
[eDVBLocalTimerHandler] time update to 20:21:31
[eDVBLocalTimerHandler] m_time_difference is -1
[eDVBLocalTimerHandler] set Linux Time
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
PATready
use pmtpid 0064 for service_id 6dca
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 5
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
eventNewProgramInfo 0 0
have 1 video stream(s) (0065), and 3 audio stream(s) (0066, 0067, 006a), and the pcr pid is 0065, and the text pid is 0068
decoder state: play, vpid=101, apid=102
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Das Erste
[showCrypted]
[showDolby]
[showMp3]
[eDVBCIInterfaces] gotPMT
[eDVBCAService] don't build/send the same CA PMT twice
sdt update done!
[__evUpdatedEventInfo]
AITready
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Das Erste
[showCrypted]
[showDolby]
[showMp3]
OCready
DMESG
BusyBox v1.21.0 (2013-07-01 22:06:01 CEST) built-in shell (ash)Enter 'help' for a list of built-in commands.
SPARK7162:~# dmesg
0
stop sh 10000, pid 18, pt 76
Reference = 0
start dmx 868c038c, sh 10000, pid 18, t 1, pt 76
SlotHandle = 20000
stop sh 10000, pid 18, pt 76
Reference = 0
start dmx 868c038c, sh 10000, pid 18, t 1, pt 76
SlotHandle = 20000
stop sh 10000, pid 18, pt 76
Reference = 0
stop sh 10000, pid 5000, pt 1447305293
Reference = 0
start dmx 868c038c, sh 10000, pid 5000, t 1, pt 1447305293
SlotHandle = 20000
stop sh 10000, pid 5000, pt 1447305293
Reference = 0
stop sh 10000, pid 3842, pt 0
Reference = 0
stop sh 10000, pid 3003, pt 808988721
Reference = 0
stop sh 10000, pid 57, pt 6578533
Reference = 0
pti_buffer_free(875b1cd0, 770048) - delta 0x a8204, thr 0x1
freeBuffer(): free = 3
SetSource(868c038c, 1)
pti_hal_set_source(): 0, 33
[nim_vz7903_status tuner_id = 0]
[nim_vz7903_status tuner_id = 0]
p->frequency is 1236500
freq is 1236
sym is 27500
NIM_CHIP_ID_M3501B ########### d3501_Search
[d3501_Search][5016]
[d3501_Search][5018]
[d3501_Search][5024]
[d3501_Search][5026]
[d3501_Search][5043]
[d3501_Search][5045]
[d3501_Search][5049]
[d3501_Search][5051]freq = 1236
[d3501_Search][5053]
[d3501_Search][5057]
param.frequency = 1236
param.u.qpsk.symbol_rate = 27500
p->frequency = 1236, p->u.qpsk.symbol_rate = 27500
[tuner vz7903]beta=250 alpha=77000 M=77250 A=4 N=16 sd=40000
i_data1 = 2 XtalFreqKHz=16000
[d3501_Search][5064]
[d3501_Search][5070]
[d3501_Search][5078]
[nim_vz7903_status tuner_id = 0]
[d3501_Search][5086]
[d3501_Search][5094]
[d3501_Search][5097]
[d3501_Search][5101]
[d3501_Search][5109]
[d3501_Search][5116]
[d3501_Search][5121]
nim_s3501_set_RS NIM_CHIP_ID_M3501B
1111111ooooooooooooo ver_data = 0x35
1111111ooooooooooooo ver_data = 0xff
nim_s3501_set_RS CR3F rs = 0xff, ver_data = 0xff
2222222ooooooooooooo ver_data = 0xdb
nim_s3501_set_RS CR40 rs = 0xdb, ver_data = 0xdb
nim_s3501_set_RS CR41 rs = 0x0, ver_data = 0x0
[d3501_Search][5128]
[d3501_Search][5134]
[d3501_Search][5139]
[d3501_Search][5151]
[d3501_Search][5157]
[d3501_Search][5161]
[d3501_Search][5167]
[d3501_Search][5189]
[d3501_Search][5236]
###########R02_IERR intdata = 0x0
###########R02_IERR intdata = 0x0
###########R02_IERR intdata = 0x0
###########R02_IERR intdata = 0x0
###########R02_IERR intdata = 0x0
###########R02_IERR intdata = 0x2
symrate ==== 0xdbfe
*sym_rate is 0x6b6b
Enter Fuction nim_s3501_reg_get_work_mode
nim_s3501_reg_get_work_mode data = 0x0
*$$$$$$$$$$$$$$$$$$work_mode = 0
lock chanel
[nim_vz7903_status tuner_id = 0]
reset_tsm: 1 numRunningFeeds: 0 => calling stm_tsm_init(1)
[TSM] reinit stream routing...
Bypass ci
reinit
TsinMode = Parallel *st-merger*
TsinMode = Parallel *st-merger*
TsinMode = Parallel *st-merger*
TsinMode = Parallel *st-merger*
start dmx 868c038c, sh 10000, pid 20, t 1, pt 45156
SlotHandle = 20000
getBuffer(): free = 3
pti_buffer_get(770048) => 875b1cd0
start dmx 868c038c, sh 10000, pid 102, t 0, pt 0
SlotHandle = 20001
(da 0, 1)linking slot 20001 to descrambler 40000, session = 10000 type=0
Find spdif_bypass control at 87550b80
Codec_MmeBase_c::SetModuleParameters - Setting selected transformer to 0
HavanaStream_c::Init: Selecting transformer 0 for stream 1
Manifestor_Base_c::SetModuleParameters - Setting buffer configuration
Mixer_Mme_c::InitializeMMETransformer: Found MME_TRANSFORMER_TYPE_AUDIO_MIXER transformer (version 70105)
Codec: Found AUDIO_DECODER transformer (version 90228)
Codec: Initializing MPEG layer I/II audio decoder
HavanaStream_c::SetId: DemuxId = 0, Id = 0x66
Demultiplexor_Base_c::AddStream - 86611000, 102.
HavanaStream_c::SetOption: 4, 1
SetPolicy - 865eba00 86611000 PolicyAVDSynchronization 1
HavanaStream_c::ChannelSelect: Channel 0
HavanaStream_c::ChannelSelect: Selecting channel 0 for stream 1
HavanaStream_c::Enable: Manifest = 1
Mixer_Mme_c::SetManifestorEmergencyMuteState: Set mute state to false (was false)
start dmx 868c038c, sh 10000, pid 101, t 0, pt 1
SlotHandle = 20002
(da 0, 2)linking slot 20002 to descrambler 40000, session = 10000 type=1
Codec_MmeBase_c::SetModuleParameters - Setting selected transformer to 0
HavanaStream_c::Init: Selecting transformer 0 for stream 2
Player:GetDisplayInfo: PlaneList 3, Plane 2, Flags 25
Player:GetDisplayInfo: Device c11e2e8c, DisplayPlaneId 2, OutputId 0, Pipeline 0
cpp_install_e2_procs: stb/video/plane/psi_brightness
cpp_install_e2_procs: stb/video/plane/psi_saturation
cpp_install_e2_procs: stb/video/plane/psi_contrast
Codec: Initializing MPEG layer I/II audio decoder
cpp_install_e2_procs: stb/video/plane/psi_tint
Sync In - 1 - 000000146df53cbd 000000146df53cbd
Sync out1 - 1 - 000000146df53cbd 000000000a01f9fc - 0000000009ffc788 ( 0)
ksound: Set parameters for hw:0,2 to 2 x 48000hz with period 1536 (of 4608)
ksound: Set parameters for hw:0,1 to 2 x 48000hz with period 1536 (of 4608)
ksound: Set parameters for hw:0,0 to 2 x 48000hz with period 1536 (of 4608)
Manifestor_Base_c::SetModuleParameters - Setting buffer configuration
Codec: Found MPEG2_TRANSFORMER0 transformer (version 0)
MME Transformer 'MPEG2_TRANSFORMER' capabilities are :-
StructSize = 0 bytes
MPEG1Capability = -2147483648
SupportedFrameChromaFormat = 1256968192
SupportedFieldChromaFormat = 56
MaximumFieldDecodingLatency90KHz = 0
SetPolicy - 865eba00 86a2b000 PolicyManifestFirstFrameEarly 1
SetPolicy - 865eba00 86a2b000 PolicyVideoBlankOnShutdown 1
HavanaStream_c::Init: Window is 1920x1080 at 0,0
HavanaStream_c::Init: Disabling Decimation
SetPolicy - 865eba00 86a2b000 PolicyDecimateDecoderOutput 0
HavanaStream_c::SetId: DemuxId = 0, Id = 0x65
Demultiplexor_Base_c::AddStream - 86a2b000, 101.
HavanaStream_c::SetOption: e, 1
SetPolicy - 865eba00 86a2b000 PolicyDisplayFormat 1
HavanaStream_c::SetOption: d, 1
SetPolicy - 865eba00 86a2b000 PolicyDisplayAspectRatio 1
HavanaStream_c::RegisterEventSignalCallback:
start dmx 868c038c, sh 10000, pid 104, t 0, pt 2
SlotHandle = 20003
start dmx 868c038c, sh 10000, pid 104, t 0, pt 20
(da 0, 3)linking slot 20003 to descrambler 40000, session = 10000 type = 20
pid 104 already collecting. references 2
start dmx 868c038c, sh 10000, pid 104, t 0, pt 20
(da 0, 3)linking slot 20003 to descrambler 40000, session = 10000 type = 20
pid 104 already collecting. references 3
***** Error-Interocitor 0: FrameParser_VideoMpeg2_c::ReadPictureHeader - Appropriate sequence header not found.
***** Error-Interocitor 0: FrameParser_VideoMpeg2_c::ReadPictureHeader - Appropriate sequence header not found.
***** Error-Interocitor 0: FrameParser_VideoMpeg2_c::ReadPictureHeader - Appropriate sequence header not found.
***** Error-Interocitor 0: FrameParser_VideoMpeg2_c::ReadPictureHeader - Appropriate sequence header not found.
***** Error-Interocitor 0: FrameParser_VideoMpeg2_c::ReadPictureHeader - Appropriate sequence header not found.
***** Error-Interocitor 0: FrameParser_VideoMpeg2_c::ReadPictureHeader - Appropriate sequence header not found.
***** Error-Interocitor 0: FrameParser_VideoMpeg2_c::ReadPictureHeader - Appropriate sequence header not found.
***** Error-Interocitor 0: FrameParser_VideoMpeg2_c::ReadPictureHeader - Appropriate sequence header not found.
start dmx 868c038c, sh 10000, pid 0, t 1, pt 131090
SlotHandle = 20004
Incoming Source 720x576 @ 0,0
Display Size 1920x1080 @ 0,0
Interlaced Content, FrameRate 25.00, PixelAspectRatio 1.422222
start dmx 868c038c, sh 10000, pid 18, t 1, pt 76
SlotHandle = 20005
DeduceFrameRateFromPresentationTime - Framerate = 25.000000
Sync In - 2 - 000000146e0086f9 000000146dfeb239
Sync out0 - 2 - 000000146df65537 000000000a031276 (326566)
Incoming Source 720x576 @ 0,0
Display Size 1920x1080 @ 0,0
Interlaced Content, FrameRate 25.00, PixelAspectRatio 1.422222
stop sh 10000, pid 0, pt 131090
Reference = 0
start dmx 868c038c, sh 10000, pid 0, t 1, pt 131090
SlotHandle = 20004
[nim_vz7903_status tuner_id = 0]
[nim_vz7903_status tuner_id = 0]
*snr = 48768
*snr = 49419
*strength = 19507
stop sh 10000, pid 20, pt 45156
Reference = 0
stop sh 10000, pid 0, pt 131090
Reference = 0
start dmx 868c038c, sh 10000, pid 0, t 1, pt 131090
SlotHandle = 20000
start dmx 868c038c, sh 10000, pid 100, t 1, pt 45156
SlotHandle = 20004
stop sh 10000, pid 0, pt 131090
Reference = 0
start dmx 868c038c, sh 10000, pid 0, t 1, pt 131090
SlotHandle = 20000
stop sh 10000, pid 0, pt 131090
Reference = 0
start dmx 868c038c, sh 10000, pid 0, t 1, pt 131090
SlotHandle = 20000
HavanaStream_c::SetOption: e, 1
SetPolicy - 865eba00 86a2b000 PolicyDisplayFormat 1
HavanaStream_c::SetOption: d, 1
SetPolicy - 865eba00 86a2b000 PolicyDisplayAspectRatio 1
stop sh 10000, pid 100, pt 45156
Reference = 0
start dmx 868c038c, sh 10000, pid 100, t 1, pt 45156
SlotHandle = 20004
start dmx 868c038c, sh 10000, pid 17, t 1, pt 874538355
SlotHandle = 20006
stop sh 10000, pid 100, pt 45156
Reference = 0
start dmx 868c038c, sh 10000, pid 100, t 1, pt 45156
SlotHandle = 20004
start dmx 868c038c, sh 10000, pid 200, t 1, pt 0
SlotHandle = 20007
stop sh 10000, pid 100, pt 45156
Reference = 0
start dmx 868c038c, sh 10000, pid 2070, t 1, pt 45156
SlotHandle = 20004
stop sh 10000, pid 2070, pt 45156
Reference = 0
start dmx 868c038c, sh 10000, pid 2070, t 1, pt 45156
SlotHandle = 20004
start dmx 868c038c, sh 10000, pid 100, t 1, pt 808988721
SlotHandle = 20008
stop sh 10000, pid 17, pt 874538355
Reference = 0
stop sh 10000, pid 200, pt 0
Reference = 0
stop sh 10000, pid 18, pt 76
Reference = 0
start dmx 868c038c, sh 10000, pid 18, t 1, pt 76
SlotHandle = 20005
[nim_vz7903_status tuner_id = 0]
[nim_vz7903_status tuner_id = 0]
*snr = 48768
*snr = 48768
*strength = 19507
Codec_MmeVideoMpeg2_c::CheckCodecReturnParameters - MPEG2_DECODER_ERROR_RECOVERED cafe0002
stop sh 10000, pid 2070, pt 45156
Reference = 0
start dmx 868c038c, sh 10000, pid 2171, t 1, pt 45156
SlotHandle = 20004
[nim_vz7903_status tuner_id = 0]
[nim_vz7903_status tuner_id = 0]
*snr = 11704
*snr = 11704
*strength = 19507
***** Error-pti_task: MPEG audio frame parser: Invalid start code 4dc00000
***** Error-Player Aud Mixer: Manifestor_AudioKsound_c::FillOutInputBuffer: Mixer has starved - injecting silence (sta:0x6001)
Codec_MmeVideoMpeg2_c::CheckCodecReturnParameters - MPEG2_DECODER_ERROR_RECOVERED cafe0002
***** Error-pti_task: MPEG audio frame parser: Invalid start code d6a00000
***** Error-Player Aud 0: Audio frame parser: Unexpected change in playback time. Expected 87746966333us, got 87747206333us (deltas: exp. 24000 got 264000 )
***** Error-Player Aud 0: Audio frame parser: Unexpected change in playback time. Expected 87747374333us, got 87747398333us (deltas: exp. 24000 got 48000 )
[nim_vz7903_status tuner_id = 0]
[nim_vz7903_status tuner_id = 0]
*snr = 11704
*snr = 11704
*strength = 19507
***** Error-pti_task: MPEG audio frame parser: Invalid start code f3e00000
Codec_MmeVideoMpeg2_c::CheckCodecReturnParameters - MPEG2_DECODER_ERROR_RECOVERED cafe0002
***** Error-Player Aud Mixer: Manifestor_AudioKsound_c::FillOutInputBuffer: Mixer has starved - injecting silence (sta:0x6001)
***** Error-pti_task: MPEG audio frame parser: Invalid start code 0
***** Error-pti_task: MPEG audio frame parser: Invalid bit rate, fffffffc, 0, 0
***** Error-pti_task: MPEG audio frame parser: Invalid bit rate, fffffcc4, 0, 0
***** Error-pti_task: MPEG audio frame parser: Invalid start code c4e00000
***** Error-Player Aud 0: Audio frame parser: Unexpected change in playback time. Expected 87748118333us, got 87748358333us (deltas: exp. 24000 got 264000 )
***** Error-Player Aud 0: Audio frame parser: Unexpected change in playback time. Expected 87748526333us, got 87748550333us (deltas: exp. 24000 got 48000 )
AVDsync Correction Video - -6762 us
stop sh 10000, pid 2171, pt 45156
Reference = 0
[nim_vz7903_status tuner_id = 0]
[nim_vz7903_status tuner_id = 0]
[nim_vz7903_status tuner_id = 0]
Spotted a delta(Video) -120000
Initiating a Jump(Video)
***** Error-Player Aud 2: OutputCoordinator_Base_c::HandlePlaybackTimeDeltas (Audio) - Stream failed to match previous jump in playback times
Sync In - 1 - 0000001478b7e03d 0000001478b7827d
Sync In - 2 - 0000001478b6d639 0000001478b639f9
***** Error-Player Aud Mixer: Manifestor_AudioKsound_c::FillOutInputBuffer: Mixer has starved - injecting silence (sta:0x6001)
ManifestorVideo_c::GetNextQueuedManifestationTime: 2 - NextTimeSlot 348474834, TimeSlotOnDisplay 348314834 Buff.TimeOnDisplay 348315948 Estimate 348475948, Now 348352244 diff 123704
{0 0000000000000000, 0000000000000001}
{0 00000000000f4240, 0000000000000032}
Sync out1 - 2 - 0000001478b6d639 0000000014c5522c - 0000000014c3cac2 ( 0)
Sync out1 - 1 - 0000001478b7e03d 0000000014c65c30 - 0000000014c3eadb ( 68100)
[nim_vz7903_status tuner_id = 0]
***** Error-pti_task: MPEG audio frame parser: Invalid start code 71800000
***** Error-pti_task: MPEG audio frame parser: Invalid start code 0
***** Error-pti_task: MPEG audio frame parser: Invalid bit rate, fffffffc, 0, 0
***** Error-pti_task: MPEG audio frame parser: Invalid bit rate, fffffcc4, 0, 0
***** Error-Player Aud Mixer: Manifestor_AudioKsound_c::FillOutInputBuffer: Mixer has starved - injecting silence (sta:0x6001)
***** Error-pti_task: MPEG audio frame parser: Invalid start code 30600000
***** Error-Player Aud 0: Audio frame parser: Unexpected change in playback time. Expected 87984254333us, got 87984518333us (deltas: exp. 24000 got 288000 )
Spotted a delta(Video) -120000
Initiating a Jump(Video)
***** Error-Player Aud 0: Audio frame parser: Unexpected change in playback time. Expected 87984686333us, got 87984710333us (deltas: exp. 24000 got 48000 )
***** Error-Player Aud 2: OutputCoordinator_Base_c::HandlePlaybackTimeDeltas (Audio) - Stream failed to match previous jump in playback times
Sync In - 1 - 000000147c4d3bfd 000000147c4cde3d
Sync In - 2 - 000000147c4c31f9 000000147c4b95b9
***** Error-Player Aud Mixer: Manifestor_AudioKsound_c::FillOutInputBuffer: Mixer has starved - injecting silence (sta:0x6001)
ManifestorVideo_c::GetNextQueuedManifestationTime: 2 - NextTimeSlot 408715949, TimeSlotOnDisplay 408555949 Buff.TimeOnDisplay 408554824 Estimate 408714824, Now 408592826 diff 121998
{0 0000000000000000, 0000000000000001}
{0 00000000000f4240, 0000000000000032}
Sync out1 - 2 - 000000147c4c31f9 00000000185c7e48 - 00000000185afe13 ( 0)
Sync out1 - 1 - 000000147c4d3bfd 00000000185d884c - 00000000185b214b ( 68100)
[nim_vz7903_status tuner_id = 0]
[nim_vz7903_status tuner_id = 0]
***** Error-pti_task: MPEG audio frame parser: Invalid start code 92e00000
***** Error-pti_task: MPEG audio frame parser: Invalid start code 1e600000
***** Error-Player Aud 0: Audio frame parser: Unexpected change in playback time. Expected 88104278333us, got 88104518333us (deltas: exp. 24000 got 264000 )
***** Error-Player Aud Mixer: Manifestor_AudioKsound_c::FillOutInputBuffer: Mixer has starved - injecting silence (sta:0x6001)
***** Error-Player Aud 0: Audio frame parser: Unexpected change in playback time. Expected 88104686333us, got 88104710333us (deltas: exp. 24000 got 48000 )
Codec_MmeVideoMpeg2_c::CheckCodecReturnParameters - MPEG2_DECODER_ERROR_RECOVERED cafe0002
***** Error-Player Aud Mixer: Manifestor_AudioKsound_c::FillOutInputBuffer: Mixer has starved - injecting silence (sta:0x6001)
also doch ein [tuner vz7903]
Powered by vBulletin® Version 4.2.5 Copyright ©2024 Adduco Digital e.K. und vBulletin Solutions, Inc. Alle Rechte vorbehalten.