Archiv verlassen und diese Seite im Standarddesign anzeigen : [AzBoxHD] Image online
kann mir wer die Ausgabe der Zeile posten:
blkid; fdisk -l; mount; cat /proc/cmdline; cat /proc/mtd
Thx ;)
Bootlogo und Spinner laufen schonmal
Das Image hängt leider noch in einer endlos Greenscreen schleife unmittelbar nach dem start (also noch vor der Erstinstallation)
Getestet auf meiner Premium
root@azboxhd:~# blkid; fdisk -l; mount; cat /proc/cmdline; cat /proc/mtd
/dev/mtdblock3: LABEL="YAMON_XRPC" TYPE="romfs"
/dev/hda1: UUID="68eec5e9-c937-4436-8f9a-f0fd7d48d4ee" TYPE="ext3"
/dev/hda3: UUID="829dde79-1957-4092-996a-0e26158c1e93" TYPE="swap"
/dev/hda2: UUID="8c9b5503-ffa5-44c4-addd-c4a656f9a5e8" TYPE="ext2"
/dev/hdb1: UUID="019a4661-ffbd-45b5-8fcb-2fe760aa2432" TYPE="ext2"
/dev/mtdblock/4: LABEL="MIPS_LINUX_XRPC" TYPE="romfs"
/dev/mtdblock/3: LABEL="YAMON_XRPC" TYPE="romfs"
/dev/mtdblock4: LABEL="MIPS_LINUX_XRPC" TYPE="romfs"
-sh: fdisk: not found
rootfs on / type rootfs (rw)
/dev/hda1 on / type ext3 (rw,relatime,errors=continue,barrier=1,data=ordere d)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
tmpfs on /media type tmpfs (rw,relatime,size=64k)
/dev/hdb1 on /media/usb type ext2 (rw,relatime,errors=continue)
tmpfs on /var/volatile type tmpfs (rw,relatime)
usbfs on /proc/bus/usb type usbfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,gid=5,mode=620)
mem=107m console=ttyS0,115200
dev: size erasesize name
mtd0: 00800000 00010000 "CS2: Physically mapped flash"
mtd1: 00020000 00010000 "CS2-Part1"
mtd2: 00020000 00010000 "CS2-Part2"
mtd3: 00040000 00010000 "CS2-Part3"
mtd4: 00680000 00010000 "CS2-Part4"
mtd5: 00100000 00010000 "CS2-Part5"
Auch meine Premium HD+ startet mit einer Bootschleife.
anstatt fdisk -l habe ich sfdisk -l eingegeben, da auf den Azboxen sfdisk verwendet wird.
root@azboxhd:~# [6nblkid; sfdisk -l; mount; cat /proc/cmdline; cat /proc/mtd
/dev/sda2: UUID="01CD7D362D3CAEB0" TYPE="ntfs"
/dev/hda3: UUID="9b6d341e-c815-488a-8682-8c958f62071b" TYPE="swap"
/dev/sda1: UUID="f32d1af5-2e13-e84f-15c6-da96271691b9" TYPE="ext3"
/dev/hda5: UUID="dd1cf8f2-5913-48fc-8f93-db2b5f860733" TYPE="ext3"
/dev/hda2: UUID="b74cb93f-d4cb-48f3-a735-84af160cefe2" TYPE="ext2"
/dev/mtdblock3: LABEL="YAMON_XRPC" TYPE="romfs"
/dev/mtdblock4: LABEL="MIPS_LINUX_XRPC" TYPE="romfs"
/dev/hda1: UUID="71cd7420-134a-4f27-ac4d-1752ff385b75" TYPE="ext3"
/dev/mtdblock/4: LABEL="MIPS_LINUX_XRPC" TYPE="romfs"
/dev/mtdblock/3: LABEL="YAMON_XRPC" TYPE="romfs"
Disk /dev/hda: 15538 cylinders, 16 heads, 63 sectors/track
Units = cylinders of 516096 bytes, blocks of 1024 bytes, counting from 0
Device Boot Start End #cyls #blocks Id System
/dev/hda1 0+ 371 372- 187487+ 83 Linux
/dev/hda2 372 380 9 4536 83 Linux
/dev/hda3 381 498 118 59472 82 Linux swap / Solaris
/dev/hda4 499 15537 15039 7579656 5 Extended
/dev/hda5 499+ 15537 15039- 7579655+ 83 Linux
Disk /dev/mtdblock0: 1 cylinders, 255 heads, 63 sectors/track
sfdisk: ERROR: sector 2006605284 does not have an msdos signature
sfdisk: /dev/mtdblock0: unrecognized partition table type
sfdisk: No partitions found
Disk /dev/mtdblock1: 0 cylinders, 255 heads, 63 sectors/track
sfdisk: ERROR: sector 2006605284 does not have an msdos signature
sfdisk: /dev/mtdblock1: unrecognized partition table type
sfdisk: No partitions found
Disk /dev/mtdblock2: 0 cylinders, 255 heads, 63 sectors/track
sfdisk: ERROR: sector 2006605284 does not have an msdos signature
sfdisk: /dev/mtdblock2: unrecognized partition table type
sfdisk: No partitions found
Disk /dev/mtdblock3: 0 cylinders, 255 heads, 63 sectors/track
sfdisk: ERROR: sector 2006605284 does not have an msdos signature
sfdisk: /dev/mtdblock3: unrecognized partition table type
sfdisk: No partitions found
Disk /dev/mtdblock4: 0 cylinders, 255 heads, 63 sectors/track
sfdisk: ERROR: sector 2006605284 does not have an msdos signature
sfdisk: /dev/mtdblock4: unrecognized partition table type
sfdisk: No partitions found
Disk /dev/mtdblock5: 0 cylinders, 255 heads, 63 sectors/track
sfdisk: ERROR: sector 2006605284 does not have an msdos signature
sfdisk: /dev/mtdblock5: unrecognized partition table type
sfdisk: No partitions found
Disk /dev/sda: 121601 cylinders, 255 heads, 63 sectors/track
Units = cylinders of 8225280 bytes, blocks of 1024 bytes, counting from 0
Device Boot Start End #cyls #blocks Id System
/dev/sda1 0+ 57859 57860- 464760418+ 83 Linux
/dev/sda2 57860 121600 63741 511999582+ 7 HPFS/NTFS/exFAT
/dev/sda3 0 - 0 0 0 Empty
/dev/sda4 0 - 0 0 0 Empty
rootfs on / type rootfs (rw)
/dev/hda1 on / type ext3 (rw,relatime,errors=continue,barrier=1,data=ordere d)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
tmpfs on /media type tmpfs (rw,relatime,size=64k)
/dev/sda1 on /media/usb type ext3 (rw,relatime,barrier=1,data=ordered)
devpts on /dev/pts type devpts (rw,relatime,gid=5,mode=620)
tmpfs on /var/volatile type tmpfs (rw,relatime)
usbfs on /proc/bus/usb type usbfs (rw,relatime)
/dev/hda5 on /media/DOMExtender type ext3 (rw,relatime,errors=continue,barrier=1,data=ordere d)
/dev/hda5 on /usr type ext3 (rw,relatime,errors=continue,barrier=1,data=ordere d)
mem=107m console=ttyS0,115200
dev: size erasesize name
mtd0: 00800000 00010000 "CS2: Physically mapped flash"
mtd1: 00020000 00010000 "CS2-Part1"
mtd2: 00020000 00010000 "CS2-Part2"
mtd3: 00040000 00010000 "CS2-Part3"
mtd4: 00680000 00010000 "CS2-Part4"
mtd5: 00100000 00010000 "CS2-Part5"
Das ging ja schnell mit dem Image.
Aber wenn ich die Kommentare dazu lese ,warte ich lieber noch.
Wie wird denn das Image installiert?
So wie alle anderen E2-Images. Mittels Azup 2.2.7 von deinem PC aus.
My Friends ... error loop white-crash ... tested on Ultra model:
crashlog
<?xml version="1.0" encoding="utf-8"?>
<HDMU>
<enigma2>
<crashdate>Fri Mar 8 11:20:49 2013</crashdate>
<compiledate>Nov 9 2013</compiledate>
<skin>skin.xml</skin>
<sourcedate>2013-11-09</sourcedate>
<rev>
<![CDATA[
-----====== HDMU 11705 enigma2 Git 796 ======-----
]]>
</rev>
<freespace>
<![CDATA[
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/hda1 181500 142872 29260 83% /
tmpfs 64 0 64 0% /media
tmpfs 51040 248 50792 0% /var/volatile
]]>
</freespace>
<freeram>
<![CDATA[
total used free shared buffers
Mem: 102080 100260 1820 0 7108
-/+ buffers: 93152 8928
Swap: 59388 0 59388
]]>
</freeram>
<version>3.0.0</version>
</enigma2>
<image>
<stbmodel>azboxhd</stbmodel>
<kernelversion>
<![CDATA[
Linux azboxhd 3.9.2-opensat #1 PREEMPT Sat Nov 9 02:51:06 CET 2013 mips GNU/Linux
]]>
</kernelversion>
<kernelcmdline>mem=107m console=ttyS0,115200</kernelcmdline>
<nimsockets>NIM Socket 0:</nimsockets>
<imageversion>
<!-- No such file or directory -->
</imageversion>
<imageissue>
<![CDATA[
mips 3.1 %h
]]>
</imageissue>
</image>
<crashlogs>
<enigma2crashlog>
<![CDATA[
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
+ (9) GFBDC
16352k video mem
- double buffering available!
9152kB available for acceleration surfaces.
resolution: 1280 x 720 x 32 (stride: 5120)
+ (9) gLCDDC
found OLED display!
lcd buffer 0x7e6280 8448 bytes, stride 132
LCD resolution: 132 x 64 x 8 (stride: 132)
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) UHF Modulator
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "dreambox advanced remote control (native)" is a remotecontrol
Found 1 input devices.
+ (22) Hdmi CEC driver
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
done, found 0 common interface slots
+ (35) CA handler
+ (36) Stream server
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryDVD
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
---- opening lame channel db
reading services (version 4)
loaded 6444 services
scanning for frontends..
opening frontend 0
close frontend 0
boxtype detection via /proc/stb/info not possible... use fallback via demux count!
found 1 adapter, 1 frontends(1 sim) and 3 demux, boxtype 1
Use valid Linux Time :) (RTC?)
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
Loading spinners...
[ePNG] couldn't open /usr/share/enigma2/skin_default/spinner/wait13.png
found 12 spinner!
setIoPrio best-effort level 3 ok
main thread is non-idle! display spinner!
Failed to open /dev/dbox/fp0
[Harddisk] enumerating block devices...
new Harddisk hda -> /dev/hda -> /dev/hda
[ePopen] command: ('sdparm', 'sdparm', '--set=SCT=0', '/dev/hda')
unable to load config ([Errno 2] No such file or directory: '/etc/enigma2/settings'), assuming defaults...
Reading satellites.xml
sec config cleared
setSlotInfo for dvb frontend 0 to slotid 0, descr STV090x Multistandard, need rotorworkaround No, enabled Yes, DVB-S2 Yes
slot: 0 configmode: simple
diseqcmode: diseqc_a_b
sec config completed
[InfoBar] Failed to load resumepoints: [Errno 2] No such file or directory: '/home/root/resumepoints.pkl'
loading bouquet... /etc/enigma2/bouquets.tv 1
loading bouquet... /etc/enigma2/userbouquet.mein_tv.tv 1
47 entries in Bouquet userbouquet.mein_tv.tv
loading bouquet... /etc/enigma2/userbouquet.hdtv.tv 48
36 entries in Bouquet userbouquet.hdtv.tv
loading bouquet... /etc/enigma2/userbouquet.sky_hdtv.tv 84
19 entries in Bouquet userbouquet.sky_hdtv.tv
loading bouquet... /etc/enigma2/userbouquet.sky_cinema.tv 103
10 entries in Bouquet userbouquet.sky_cinema.tv
loading bouquet... /etc/enigma2/userbouquet.sky__welt___extra.tv 113
35 entries in Bouquet userbouquet.sky__welt___extra.tv
loading bouquet... /etc/enigma2/userbouquet.sky_bundesliga.tv 148
21 entries in Bouquet userbouquet.sky_bundesliga.tv
loading bouquet... /etc/enigma2/userbouquet.sky_sport.tv 169
38 entries in Bouquet userbouquet.sky_sport.tv
loading bouquet... /etc/enigma2/userbouquet.austriasat.tv 207
13 entries in Bouquet userbouquet.austriasat.tv
loading bouquet... /etc/enigma2/userbouquet.kinder.tv 220
12 entries in Bouquet userbouquet.kinder.tv
loading bouquet... /etc/enigma2/userbouquet.musik.tv 232
16 entries in Bouquet userbouquet.musik.tv
loading bouquet... /etc/enigma2/userbouquet.oesterreich.tv 248
27 entries in Bouquet userbouquet.oesterreich.tv
loading bouquet... /etc/enigma2/userbouquet.italien.tv 275
89 entries in Bouquet userbouquet.italien.tv
loading bouquet... /etc/enigma2/userbouquet.schweiz.tv 364
20 entries in Bouquet userbouquet.schweiz.tv
loading bouquet... /etc/enigma2/userbouquet.holland.tv 384
23 entries in Bouquet userbouquet.holland.tv
loading bouquet... /etc/enigma2/userbouquet.sky_select.tv 407
14 entries in Bouquet userbouquet.sky_select.tv
loading bouquet... /etc/enigma2/userbouquet.xxx.tv 421
47 entries in Bouquet userbouquet.xxx.tv
loading bouquet... /etc/enigma2/userbouquet.favourites.tv 468
0 entries in Bouquet userbouquet.favourites.tv
17 entries in Bouquet bouquets.tv
loading bouquet... /etc/enigma2/bouquets.radio 1
loading bouquet... /etc/enigma2/userbouquet.deutsche.radio 1
19 entries in Bouquet userbouquet.deutsche.radio
loading bouquet... /etc/enigma2/userbouquet.favourites.radio 20
0 entries in Bouquet userbouquet.favourites.radio
2 entries in Bouquet bouquets.radio
[FONT] adding font /usr/share/fonts/nmsbd.ttf...OK (Regular)
[FONT] adding font /usr/share/fonts/andale.ttf...OK (Fixed)
[FONT] adding font /usr/share/fonts/goodtime.ttf...OK (Crs)
[FONT] adding font /usr/share/fonts/age.ttf...OK (Age)
[FONT] adding font /usr/share/fonts/tuxtxt.ttf...OK (Console)
[FONT] adding font /usr/share/fonts/time.ttf...OK (BMCTime)
[FONT] adding font /usr/share/fonts/ae_AlMateen.ttf...OK (Replacement)
[FONT] adding font /usr/share/fonts/md_khmurabi_10.ttf...OK (Regular)
[FONT] adding font /usr/share/fonts/valis_lcd.ttf...OK (Digital)
[FONT] adding font /usr/share/fonts/valis_enigma.ttf...OK (Subs)
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 25] Inappropriate ioctl for device >
Activating keymap: Default (US)
[ePopen] command: loadkmap < /usr/share/keymaps/default.kmap
Activating language English
[ePopen] command: ip -o addr show dev eth0
setLCDBrightness 25
[LCD] can't open /dev/dbox/fp0
setLCDBrightness 127
[LCD] can't open /dev/dbox/fp0
getModeList for port DVI-PC
remove DVI-PC because of not existing modes
getModeList for port YPbPr
getModeList for port Scart
getModeList for port DVI
hotplug on dvi
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
setMode - port: YPbPr mode: 720p rate: 50Hz
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
[NetworkBrowser] fallback to default translation for NetworkBrowser
[NetworkBrowser] fallback to default translation for Search for network shares
[NetworkBrowser] fallback to default translation for MountManager
[NetworkBrowser] fallback to default translation for Manage network shares
[NetworkBrowser] fallback to default translation for Mount again
[NetworkBrowser] fallback to default translation for Attempt to mount shares again
[WebInterface] set language to en
[WebInterface] set language to en
[WebInterface] fallback to default translation for Webinterface
[WebInterface] fallback to default translation for Configuration for the Webinterface
Media Center: Import evfd failed
loadSkin: Screen already defined elsewhere: HDMU_MainMenu
loadSkin: Screen already defined elsewhere: HDMU_SoftcamControl
loadSkin: Screen already defined elsewhere: HDMU_OverclockControl
loadSkin: Screen already defined elsewhere: HDMU_SystemControl
loadSkin: Screen already defined elsewhere: HDMU_TunerControl
loadSkin: Screen already defined elsewhere: HDMU_SystemInfos
loadSkin: Screen already defined elsewhere: HDMU_ufsup
loadSkin: Screen already defined elsewhere: HDMU_OSDControl
loadSkin: Screen already defined elsewhere: HDMU_VFDControl
loadSkin: Screen already defined elsewhere: HDMU_VideoControl
loadSkin: Screen already defined elsewhere: HDMU_DLNAServer
loadSkin: Screen already defined elsewhere: HDMU_OpenVPN
loadSkin: Screen already defined elsewhere: HDMU_SkinControl
HDMU Center: Import evfd failed
starting hotplug handler
wasTimerWakeup failed!
[SKIN] No skin to read...
[Toplevel.importExternalModules] Imported external module: Example
[HTTPRootResource}.__init__
[Webinterface] started on 0.0.0.0:80 auth=False ssl=False
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[HTTPRootResource}.__init__
[Webinterface] started on 0.0.0.0:443 auth=True ssl=True
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[EPGC] setCacheFile read/write epg data from/to '/hdd/epg.dat'
[EPGC] time updated.. start EPG Mainloop
[EPGC] /hdd/epg.dat not found, try /epg.dat
Reading ['/usr/lib/enigma2/python/Plugins/SystemPlugins/Videomode/videowizard.xml']
getStepWithID: start
result: nothing
('en_EN', ('English', 'en', 'EN'))
Screen <function VideoWizard at 0x13c1570>((), {}): <type 'exceptions.IOError'>
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 225, in create
return screen(self, *arguments, **kwargs)
File "/usr/lib/enigma2/python/Plugins/SystemPlugins/Videomode/plugin.py", line 230, in VideoWizard
File "/usr/lib/enigma2/python/Plugins/SystemPlugins/Videomode/VideoWizard.py", line 54, in __init__
File "/usr/lib/enigma2/python/Screens/Rc.py", line 26, in __init__
File "/usr/lib/enigma2/python/Screens/Rc.py", line 41, in readPositions
File "/usr/lib/python2.7/xml/etree/ElementTree.py", line 611, in __init__
File "/usr/lib/python2.7/xml/etree/ElementTree.py", line 646, in parse
IOError: [Errno 2] No such file or directory: '/usr/share/enigma2/rc_models/xpeedlx/rcpositions.xml'
open /dev/dbox/fp0 for wakeup timer clear failed!(No such file or directory)
EXCEPTION IN PYTHON STARTUP CODE:
------------------------------------------------------------
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 593, in <module>
runScreenTest()
File "/usr/lib/enigma2/python/mytest.py", line 477, in runScreenTest
runNextScreen(session, screensToRun)
File "/usr/lib/enigma2/python/mytest.py", line 471, in runNextScreen
session.openWithCallback(boundFunction(runNextScre en, session, screensToRun[1:]), screen, *args)
File "/usr/lib/enigma2/python/mytest.py", line 293, in openWithCallback
dlg = self.open(screen, *arguments, **kwargs)
File "/usr/lib/enigma2/python/mytest.py", line 304, in open
dlg.isTmp = True
AttributeError: 'NoneType' object has no attribute 'isTmp'
open /dev/dbox/fp0 for wakeup timer clear failed!(No such file or directory)
------------------------------------------------------------
(exit code 5)
getResolvedKey config.plugins.crashlogautosubmit.sendAnonCrashlog failed !! (Typo??)
getResolvedKey config.plugins.crashlogautosubmit.addNetwork failed !! (Typo??)
getResolvedKey config.plugins.crashlogautosubmit.addWlan failed !! (Typo??)
]]>
</enigma2crashlog>
</crashlogs>
</HDMU>
Ciao ... :)
Thx - kann man das Image auch via Stick flashen?
Nein Morly, geht nur via PC Tool.
thanks - hab mich gerade eingelesen :)
@Morly ...
For first time run ... resolve the wrong assign rcpositions xml path ... with this ... /usr/share/enigma2/rc_models/azboxhd/rcpositions.xml
Now ... the wizard is OK and run ! :)
56475648
Ciao ...
war dann doch schon zu spät , das Image davor ging noch lol
neues baut grad
@bonkel
Sorry ... but with new version HDMU_11706_AzboxHD_OE_796_Flash ... not resolve !
... new issue come on Enigma2 python side:
root@azboxhd:~# enigma2.sh
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
+ (9) GFBDC
16352k video mem
- double buffering available!
9152kB available for acceleration surfaces.
resolution: 1280 x 720 x 32 (stride: 5120)
+ (9) gLCDDC
found OLED display!
lcd buffer 0x7e65c0 8448 bytes, stride 132
LCD resolution: 132 x 64 x 8 (stride: 132)
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) UHF Modulator
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "dreambox advanced remote control (native)" is a remotecontrol
Found 1 input devices.
+ (22) Hdmi CEC driver
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
done, found 0 common interface slots
+ (35) CA handler
+ (36) Stream server
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryDVD
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
---- opening lame channel db
reading services (version 4)
loaded 6444 services
scanning for frontends..
opening frontend 0
close frontend 0
boxtype detection via /proc/stb/info not possible... use fallback via demux coun t!
found 1 adapter, 1 frontends(1 sim) and 3 demux, boxtype 1
Use valid Linux Time :) (RTC?)
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
Loading spinners...
[ePNG] couldn't open /usr/share/enigma2/skin_default/spinner/wait13.png
found 12 spinner!
executing main
setIoPrio best-effort level 3 ok
main thread is non-idle! display spinner!
Failed to open /dev/dbox/fp0
[Harddisk] enumerating block devices...
new Harddisk hda -> /dev/hda -> /dev/hda
[ePopen] command: ('sdparm', 'sdparm', '--set=SCT=0', '/dev/hda')
unable to load config ([Errno 2] No such file or directory: '/etc/enigma2/settin gs'), assuming defaults...
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 18, in <module>
from Screens import InfoBar
File "/usr/lib/enigma2/python/Screens/InfoBar.py", line 5, in <module>
File "/usr/lib/enigma2/python/Screens/MovieSelection.py", line 1, in <module>
File "/usr/lib/enigma2/python/Screens/Screen.py", line 4, in <module>
File "/usr/lib/enigma2/python/Components/GUISkin.py", line 1, in <module>
File "/usr/lib/enigma2/python/Components/GUIComponent.py", line 1, in <module>
File "/usr/lib/enigma2/python/skin.py", line 15, in <module>
File "/usr/lib/enigma2/python/Components/RcModel.py", line 81, in <module>
File "/usr/lib/enigma2/python/Components/RcModel.py", line 15, in __init__
File "/usr/lib/enigma2/python/Components/RcModel.py", line 32, in readRcTypeFr omProc
AttributeError: RcModel instance has no attribute 'RCTYPE_AZBOXHD'
---- saving lame channel db
saved 236 channels and 6444 services!
release cached channel (timer timeout)
set RTC to previous valid time
- (41) eServiceFactoryDVD
- (41) eServiceFactoryM2TS
- (41) eServiceFactoryMP3
- (41) eServiceFactoryFS
- (41) eServiceFactoryDVB
- (40) eServiceCenter
clear instance
- (36) Stream server
- (35) CI Slots
- (35) CA handler
- (30) eActionMap
- (22) Hdmi CEC driver
- (21) input device driver
- (20) DVB-CI UI
- (20) UHF Modulator
- (20) RC Input layer
- (20) misc options
- (20) AVSwitch Driver
- (15) eWindowStyleManager
- (10) gRC
waiting for gRC thread shutdown
gRC thread has finished
- (9) GFBDC
- (9) gLCDDC
- (9) Font Render Class
- (8) graphics acceleration manager
- (5) Tuxtxt
- (1) Background File Eraser
reached rl -1
root@azboxhd:~#
Ciao ...
@bonkel
Thanks for new 11707 ... but You are came back to first issue 11705 version :)
5651
The save path in your compile source system "by default" for files "rc.png" & "rcpositions.xml" is /usr/share/enigma2/rc_models/xpeedlx/ ... but of course this folder does not exist in the AZBox compiled system.
You must change in /usr/share/enigma2/rc_models/azboxhd/ ... and after all is OK ... with inizialize wizard setup !
I hope now it is clearer ... :)
Ciao ...
how fast are you ? lol
2 minutes after upload, i delete this Image, because of missing fix :D
there is a new on the way ^^
Das gleiche Fehlerbild habe ich auf meiner Premium HD+ mit 11707
Edit: Aha Bonkel hat es schon gesehen.
how fast are you ? lol
2 minutes after upload, i delete this Image, because of missing fix :D
there is a new on the way ^^
Ok ... i re-check :) Thanks
Mit 11708 auch die gleiche Fehlermeldung wie das Bild von Beitrag 15.
For me the 11708 version ... now is OK
P.S. But you chose the easy general way for rc_models ! :)
5652
Only one thing ... if you can make a little change on delay time for RCU control (interval between keys when repeating) ... by default 100 ms is too short ... better 300 ms ... for correct response in OSD menu system !
... we can go further with other tests! :)
Thank a lot ... @bonkel
zeini kannst nochmal neu laden, oder vielleicht falsche Datei geflashed?
ich seh jetzt kein fehler mehr
was ich noch fragen wollt, wenn ihr euren tv ohne overscan benutzt, ist bei euch das osd also die gui auch zu klein?
besonders gut im mediaportal zu sehen
das sind eigentlich alles Skins, die das ganze bild ausfüllen , so zumindest bei sh4,arm und anderen mips
denke das liegt an den treibern, wäre schön wenn das jemand the-ripper weiterleiten könnte
Ich habe bei mir den Pfad /usr/share/enigma2/rc_models/azboxhd auf /usr/share/enigma2/rc_models/xpeedlx geändert.
Nun funzt es bei mir.
Ich kann aber keine Aufnahmen abspielen. Weder von anderen Images, noch jene, die mit diesem Image aufgenommen wurden. Weder im Mediaplayer noch im Mediacenter. Wenn ich das Mediacenter verlassen will, habe ich Dauerspin, oder heißt es hier HDMU-Wackler. ;)
Ansonsten schaut es mal ganz gut aus.
aufnahmen hab ich nich getestet...(war da nich was mit kernel3.9.2?)
das mit mediacenter spinner beim verlassen hab ich auch :( (seh im log aber nich wo was stört)
Webradio geht aber....mediaportal streams gehen auch
This is my set default 1080i 50 ... with ASUS 23 LCD Full HD HDMI ... I do not think there are problems with the OSD skin!
5653
- A / V streams run with mediaportal
- HDMU Mediacenter ... same problem of zeini
- Network HDD CIFS mount not work with Network Browser ( I must test some TS record on AZBox Premium HDD)
yes in screenshots ist ok..but on tv, there is a black border
ravemaster
09.11.2013, 18:03
Was denkst du, soll an den Treibern geändert werden, damit das funktioniert? Das Problem mit zu kleinen Skins hatten wir glaub ich noch nicht.
Ich habs leider selber noch nicht testen können.
gute frage
da das tv bild passt, kanns ja nur irgendwas sein, was im bcm teil drin ist Linux/fb.cpp(.h)
bei manchen boxen kann man auch per Telnet im proc eintrag die gui vergrössern und verkleinern, vielleicht ist da auch schon was verkleinert, als vorsorge für overscan
Das Bild schaut auf meinem TV eigentlich normal aus. Ist eigentlich bei allen Receivern ähnlich.
Ich hänge mal ein F5654oto vom Mediaportal hier an.
Im Radiomodus habe ich keinen Ton.
Die Guidetaste ist eigentlich auch ungewohnt für den Aufruf des Mediaplayers. Hier wäre mE der grafische EPG besser aufgehoben.
overscan aktiv?
ich mach mal nen Foto gleoch
noch besser sieht mans wenn man media Center öffnet
dann is im Hintergrund tv bild noch zu sehen
yes in screenshots ist ok..but on tv, there is a black border
@bonkel ... but I don't see any Black border on screen !?!
56585659
What have you changed in 11709?
http://www.hdmedia-universe.com/board/pages.php?pageid=4&log=MIPSenigma2
Ja, Bonkel, das habe ich auch, wenn ich am TV es so einstelle. Aber beim normalen Bild - ohne OSD - sehe ich trotzdem alles bis zum Rand. Also ist das für mich so in Ordnung.
Beim Radioton, der nicht funzt meinte ich nicht das Webradio. Ich meinte die Radiosender am Sat. Bei diesen habe ich keinen Ton.
ravemaster
09.11.2013, 18:56
Zum Problem mit den Balken um die GUI herum. Das Problem hier ist, dass die SIGMA OSD Skalierung nicht besonders gut funktioniert. Darum sind bei manchen TV's Balken (TV-Bild) um die GUI herum. Bei einigen mehr, bei anderen weniger.
Die gewünschten Dateien hab ich gerade bekommen und hier angehängt.
5660
5661
perfekt
hab mal die sleeps geändert, das hab ich schon bei ufs912 und spark so gemacht, ergebniss war ein schnelleres zappen, kannst mal fragen ob er mir daraus mal fertige module bauen kann
ravemaster
09.11.2013, 20:46
Ich werd das gleich mal weiterleiten.
- - - Aktualisiert - - -
So das Modul ist fertig und angehängt. :36_2_35:
5664
interessantes ergebniss....wenn man ext4 im kernel aktiviert, startet die box nimmer und bleibt im boot hängen :D
ravemaster
09.11.2013, 21:10
Für ext4 sind glaub ich mehr Anpassungen notwendig. Da hat Fabry im Board von openRSI mehr Erfahrung. Er hat einen angepassten Kernel veröffentlicht, der ext4 aktiviert hat.
ext2 und ext3 sind deaktiviert. Die werden von ext4 verwaltet.
ich darf jetzt erstmal recovern :36_2_35::36_2_24:
ravemaster
09.11.2013, 21:20
Ja, so sind unsere AzenZicken. Einmal eine Kleinigkeit anders und schon liebt sie dich nicht mehr. :)
Ich habe mal die stv090x.co ausgetauscht, mit der hier im Beitrag 37 von Ravemaster angehängten getauscht, der ja von Bonkel beschleunit wurde. Mir kommt vor, dass die Box auch mit diesem Treiber ähnlich schnell umschaltet wie vorher. Ist aber immer schwer zu sagen, wenn man keinen direkten Vergleich nebeneinander hat.
Leopold75
11.11.2013, 23:04
Hallo!
Image für AzBox Elite - er hat diesen Fehler an sich
00:01:31.960 R2[emucworks]: ECM queue size = 32
*** glibc detected *** ./wicardd-mipsel: double free or corruption (top): 0x004c0420 ***
Aborted
Was soll damit werden?
Vielen Dank!
Hello Gentleman
I am new to this forum, I am glad I join it and ready to learn from you guys.
I have a Azbox P+ I installed the new image and it looks very nice, I am kind of limited regarding the satellites choices, I live in the WEST, I would like to ask if western satellite could be added to the list, KU AND C-BAND.
My performance of satellites would be form 58W TO 129W KU BAND AND C-BAND.
I have a satellite list and in the past I been able to added to the image. I try to access the files with DCC an MAX tools, but it does not let me, I think Telnet does not connect.
If there is another program I can use to add my satellite list, please provide me with this information.
And one last request, maybe is to much to ask, but, here in the WEST we do a lot of Blind Scanning, I noticed that Blind Scan is not a option under the service Menu, is this option going to be added later?
Best regards.
let's have some fun.
Chewie
did you enter he right Password?
Hello Bonkel
Thanks for your quick response, if you are referring to the MAZ program it was set to ID - AZBOX AND PW -ROOT, I never had to set the password on the RCC program, what should it be? is it the same as the MAZ program?
please let me know.
Regards.
Chewie
Thanks bonkel, I will try it out when I get home.
Another question, the Fan on the receiver stays on when the receiver is set to Standby, I was looking for the option to have the fan turn off while on the Standby, is there such an option on this image, I was not able to locate this option.
Please let me know.
Thanks in advance.
Regards
Chewie
it's a Alpha Image, there is no Option for that at the Moment, have other Problems with this box ^^
I hope you receive all the necessary support from Sasha ... because your distrubution has all the elements to be an excellent Enigma 2 distribution for old AZBox!
Congratulations @ bonkel and friends :)
Hello Bonkel
I was able to load my Sat list to this firm and it works very good so far, WiFi works good. I thank you for your help and thanks for this image.
Regards.
Chewie
papaluna
16.11.2013, 09:34
Because to install this image on usb, simpre which was started Dom, questions can only be installed in Dom and there is no possibility in usb. thanks
macmanolo
16.11.2013, 20:52
So. heute morgen habe ich meine AZBoxHD Premium repariert (hatte eine durchgebrannte Transistor in SMD-Format, in zur ersetzte war eine Zircus Arbeit), dan habe ich sofort der Firmware von HDMU geflash und hat alles funktioniert außer dem Tuner DVB-T, er wird ezwar erkant kan aber keine kanäle sehen auch nicht nach eine neue Suche, (0 kanäle gefunden), in sat alles ok.
Als Alpha-Version ist garnicht schlecht, ich freue mich son auf die folgenden Entwicklungen im diesen image.
Danke am alle betiligte für die gute arbeit.
mfg.
Hallo Bonkel, ist die Azbox wieder ok?
Ich würde mich sehr freuen über neue Image.
nein, treiber mag noch nicht
ravemaster
23.11.2013, 11:17
Hallo bonkel.
Wie siehts aus mit deiner Box? Können wir dir irgendwie behilflich sein?
ich arbeite mit win8..hab den treiber mittlerweile zum laufen kekommen....
bekomme aber keine ausgabe im putty
wenn ich die box an mach kommt, power on , booting und das wars
wie gesagt keine ausage im putty....
wenn du ne Idee hast wäre gut ^^
hat sich erledigt, hab jetzt ne ausgabe
irgendwie is tx und rx vertauscht , hab jetzt 4 mal geprüft und dachte schon bin bescheuert
When you do more things ... can happen :)
Are you able to go ahead with implementations?
Thanks for your time ...
Ciao
ravemaster
23.11.2013, 18:53
Das war bei mir gleich. War auch vertauscht. Ich hoffe du kriegst das Teil jetzt wieder zum Laufen. Ich hatte auch noch Probs mit dem TFTP-Server vom Paket. Hab mir dann die 64 Bit Version geladen. Mit dem gings.
wichtig ist neu zu flashen...online update könnte in die hose gehen
Super, dass sich da wieder was tut!
Neu geflasht mit HDMU_11850_AzboxHD_OE_834_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11850_AzboxHD_OE_834_Flash.zip).
Aufnahmen lassen sich aber leider immer noch nicht abspielen. edit: Funzt nach reboot
Im Radiomodus (Satradio nicht Webradio) werden die Kanäle etwa 1 Sekunde angespielt und dann ist der Ton weg.
Will man dann vom Radiomodus in den TV-Modus wechseln mit der TV/Radiotaste so funzt das nicht.
Das wären mal die wichtigsten Bugs, die gefixt werden sollten.
ich habe aufnahmen extra getestet
deswegen wollte ich ja ext4 haben.....
bei mir klappts....auch timeshift geht
Danke, stimmt!
Nach neuerlichem reboot funzt jetzt auch bei mir das Abspielen von Aufnahmen. Auch Timeshift.
As I asked for previous versions ... even if you add the cifs module and its management ... I could try recording on HDD ... installed on another az receiver !
Thank you
Ciao ...
I saw that you compiled a new version 11853 [oe 837]!
What's new changelog ?
On the previous version (oe 835) I've noticed that you've enabled the cifs ... but I always had problems with its mount!
Thanks ...
Ciao
I have installed now ... the new version 11853 [oe 837] ... but there is a problem at first boot (before started setup Wizard):
Enigma 2 white crashlog
<?xml version="1.0" encoding="utf-8"?>
<HDMU>
<enigma2>
<crashdate>Fri Mar 8 11:21:53 2013</crashdate>
<compiledate>Nov 24 2013</compiledate>
<skin>skin.xml</skin>
<sourcedate>2013-11-24</sourcedate>
<rev>
<=!=[=C=D=A=T=A=[
-----====== HDMU 11853 enigma2 Git 835 ======-----
]=]=>
</rev>
<freespace>
<=!=[=C=D=A=T=A=[
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/hda1 181500 142880 29252 83% /
tmpfs 64 0 64 0% /media
tmpfs 50980 248 50732 0% /var/volatile
/dev/sda1 3910152 1273040 2637112 33% /media/usb
]=]=>
</freespace>
<freeram>
<=!=[=C=D=A=T=A=[
total used free shared buffers
Mem: 101964 100248 1716 0 11696
-/+ buffers: 88552 13412
Swap: 59388 4 59384
]=]=>
</freeram>
<version>3.0.0</version>
</enigma2>
<image>
<stbmodel>azboxhd</stbmodel>
<kernelversion>
<=!=[=C=D=A=T=A=[
Linux azboxhd 3.9.2-opensat #1 PREEMPT Sun Nov 24 14:28:48 CET 2013 mips GNU/Linux
]=]=>
</kernelversion>
<kernelcmdline>mem=107m console=ttyS0,115200</kernelcmdline>
<nimsockets>NIM Socket 0:</nimsockets>
<imageversion>
<!-- No such file or directory -->
</imageversion>
<imageissue>
<=!=[=C=D=A=T=A=[
mips 3.1 %h
]=]=>
</imageissue>
</image>
<crashlogs>
<enigma2crashlog>
<=!=[=C=D=A=T=A=[
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
+ (9) GFBDC
16352k video mem
- double buffering available!
9152kB available for acceleration surfaces.
resolution: 1280 x 720 x 32 (stride: 5120)
+ (9) gLCDDC
found OLED display!
lcd buffer 0x7ea738 8448 bytes, stride 132
LCD resolution: 132 x 64 x 8 (stride: 132)
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) UHF Modulator
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "dreambox advanced remote control (native)" is a remotecontrol
Found 1 input devices.
+ (22) Hdmi CEC driver
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
done, found 0 common interface slots
+ (35) CA handler
+ (36) Stream server
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryDVD
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
---- opening lame channel db
reading services (version 4)
loaded 236 channels/transponders and 6444 services
scanning for frontends..
opening frontend 0
close frontend 0
boxtype detection via /proc/stb/info not possible... use fallback via demux count!
found 1 adapter, 1 frontends(1 sim) and 3 demux, boxtype 1
Use valid Linux Time :) (RTC?)
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
Loading spinners...
[ePNG] couldn't open /usr/share/enigma2/skin_default/spinner/wait13.png
found 12 spinner!
setIoPrio best-effort level 3 ok
main thread is non-idle! display spinner!
Failed to open /dev/dbox/fp0
[Harddisk] enumerating block devices...
new Harddisk hda -> /dev/hda -> /dev/hda
[ePopen] command: ('sdparm', 'sdparm', '--set=SCT=0', '/dev/hda')
new Harddisk sda -> /dev/sda -> /dev/sda
unable to load config ([Errno 2] No such file or directory: '/etc/enigma2/settings'), assuming defaults...
Reading satellites.xml
sec config cleared
setSlotInfo for dvb frontend 0 to slotid 0, descr STV090x Multistandard, need rotorworkaround No, enabled Yes, DVB-S2 Yes
slot: 0 configmode: simple
diseqcmode: diseqc_a_b
sec config completed
[InfoBar] Failed to load resumepoints: [Errno 2] No such file or directory: '/home/root/resumepoints.pkl'
[FONT] adding font /usr/share/fonts/nmsbd.ttf...OK (Regular)
[FONT] adding font /usr/share/fonts/andale.ttf...OK (Fixed)
[FONT] adding font /usr/share/fonts/goodtime.ttf...OK (Crs)
[FONT] adding font /usr/share/fonts/age.ttf...OK (Age)
[FONT] adding font /usr/share/fonts/tuxtxt.ttf...OK (Console)
[FONT] adding font /usr/share/fonts/time.ttf...OK (BMCTime)
[FONT] adding font /usr/share/fonts/ae_AlMateen.ttf...OK (Replacement)
[FONT] adding font /usr/share/fonts/md_khmurabi_10.ttf...OK (Regular)
[FONT] adding font /usr/share/fonts/valis_lcd.ttf...OK (Digital)
[FONT] adding font /usr/share/fonts/valis_enigma.ttf...OK (Subs)
[FONT] adding font /usr/share/fonts/nmsbd.ttf...OK (FdLcD)
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 25] Inappropriate ioctl for device >
[iInputDevices] setRepeat for device event0 to 150 ms
[iInputDevices] setDelay for device event0 to 700 ms
Activating keymap: Default (US)
[ePopen] command: loadkmap < /usr/share/keymaps/default.kmap
Activating language English
[ePopen] command: ip -o addr show dev eth0
setLCDBrightness 25
[LCD] can't open /dev/dbox/fp0
setLCDBrightness 127
[LCD] can't open /dev/dbox/fp0
[NetworkBrowser] fallback to default translation for NetworkBrowser
[NetworkBrowser] fallback to default translation for Search for network shares
[NetworkBrowser] fallback to default translation for MountManager
[NetworkBrowser] fallback to default translation for Manage network shares
[NetworkBrowser] fallback to default translation for Mount again
[NetworkBrowser] fallback to default translation for Attempt to mount shares again
getModeList for port DVI-PC
remove DVI-PC because of not existing modes
getModeList for port YPbPr
getModeList for port Scart
getModeList for port DVI
hotplug on dvi
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
setMode - port: YPbPr mode: 720p rate: 50Hz
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
Media Center: Import evfd failed
HDMU Center: Import evfd failed
[WebInterface] set language to en
[WebInterface] set language to en
[WebInterface] fallback to default translation for Webinterface
[WebInterface] fallback to default translation for Configuration for the Webinterface
starting hotplug handler
wasTimerWakeup failed!
setLCDBrightness 127
[LCD] can't open /dev/dbox/fp0
[NAVIGATION] USE DEEPSTAND-WORKAROUND FOR THIS BOXTYPE (azboxhd) !!
[SKIN] No skin to read...
[Toplevel.importExternalModules] Imported external module: Example
[HTTPRootResource}.__init__
[Webinterface] started on 0.0.0.0:80 auth=False ssl=False
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[HTTPRootResource}.__init__
[Webinterface] started on 0.0.0.0:443 auth=True ssl=True
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[EPGC] setCacheFile read/write epg data from/to '/hdd/epg.dat'
[EPGC] time updated.. start EPG Mainloop
[EPGC] /hdd/epg.dat not found, try /epg.dat
Reading ['/usr/lib/enigma2/python/Plugins/SystemPlugins/Videomode/videowizard.xml']
getStepWithID: start
result: nothing
('en_EN', ('English', 'en', 'EN'))
Screen <function VideoWizard at 0x149a7f0>((), {}): <type 'exceptions.IOError'>
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 227, in create
return screen(self, *arguments, **kwargs)
File "/usr/lib/enigma2/python/Plugins/SystemPlugins/Videomode/plugin.py", line 230, in VideoWizard
File "/usr/lib/enigma2/python/Plugins/SystemPlugins/Videomode/VideoWizard.py", line 54, in __init__
File "/usr/lib/enigma2/python/Screens/Rc.py", line 26, in __init__
File "/usr/lib/enigma2/python/Screens/Rc.py", line 41, in readPositions
File "/usr/lib/python2.7/xml/etree/ElementTree.py", line 611, in __init__
File "/usr/lib/python2.7/xml/etree/ElementTree.py", line 646, in parse
IOError: [Errno 2] No such file or directory: '/usr/share/enigma2/rc_models/vu/rcpositions.xml'
open /dev/dbox/fp0 for wakeup timer clear failed!(No such file or directory)
EXCEPTION IN PYTHON STARTUP CODE:
------------------------------------------------------------
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 648, in <module>
runScreenTest()
File "/usr/lib/enigma2/python/mytest.py", line 498, in runScreenTest
runNextScreen(session, screensToRun)
File "/usr/lib/enigma2/python/mytest.py", line 492, in runNextScreen
session.openWithCallback(boundFunction(runNextScre en, session, screensToRun[1:]), screen, *args)
File "/usr/lib/enigma2/python/mytest.py", line 295, in openWithCallback
dlg = self.open(screen, *arguments, **kwargs)
File "/usr/lib/enigma2/python/mytest.py", line 306, in open
dlg.isTmp = True
AttributeError: 'NoneType' object has no attribute 'isTmp'
open /dev/dbox/fp0 for wakeup timer clear failed!(No such file or directory)
------------------------------------------------------------
(exit code 5)
getResolvedKey config.plugins.crashlogautosubmit.sendAnonCrashlog failed !! (Typo??)
getResolvedKey config.plugins.crashlogautosubmit.addNetwork failed !! (Typo??)
getResolvedKey config.plugins.crashlogautosubmit.addWlan failed !! (Typo??)
]=]=>
</enigma2crashlog>
</crashlogs>
</HDMU>
please change path for "rcpositions.xml" file ... here there is a vu path (/usr/share/enigma2/rc_models/vu/) !
Another things : If you add the RtiSYS plugin system ... at least ... who has the AZPremium Plus can turn off the fan ... in standby !
Thanks ...
Ciao ...
Thanks @bonkel ... now the HDMU is ready to start ! :)
When you find the time to dedicate!
For you information ... your add RtiSYS system plugin is not good ... the plugin is not loaded !
Check the correct refer code of this python plugin ... inside python files there is your linux path /home/user ... instead of registration path on enigma2 plugin environment !
5784 5785 5786
Thanks ...
Ciao
Check the correct refer code of this python plugin ... inside python files there is your linux path /home/user ... instead of registration path on enigma2 plugin environment !
Thanks ...
Ciao
thats no Problem, ist ok
can you attach the rtisys plugin ?
thats no Problem, ist ok
can you attach the rtisys plugin ?
I have this version with the latest fix ntpdate update time ... 5790
https://github.com/OpenAZBox/RTi-SYS
Edit ... or there are custom versions of OpenRSi @Sattommy, OpenSPA, OpenATV @Captain or @Persian for oe-core ! You can ask them!
Ciao ...
Im Radiomodus (Satradio nicht Webradio) werden die Kanäle etwa 1 Sekunde angespielt und dann ist der Ton weg.
Will man vom Radiomodus in den TV-Modus wechseln mit der TV/Radiotaste so funzt das nicht.
Während einer Aufnahme sollte die rote LED an der Box leuchten.
Hallo und danke mal für dieses Image, läuft super !!!
Wäre es möglich für die AzBox und diesem Image ein NFS-Utils zu bauen?
Ich benötige noch den NFS-Server für meine AzBox.
Danke schon einmal vorab ...
opkg list *nfs* mal gemacht?
Image 11880:
Das Umschalten von TV auf Radio funzt nicht. Drückt man die TV/RADIO Taste tut sich nichts.
Image 11887:
Radiosender & TV/RADIO Taste geht nicht!
bonkel,geht das auf deiner Azbox?
@bonkel
Always ... when you have time !?! :rolleyes:
You must to control ... because the CIFS mount not goes fine (not green icon on net mount device) !
5919
With my others receivers with E2 OpenPLi (Alien 2+ & Mediabox HD LX-1) ... I don't have this problem !
Thanks & Ciao ...
So wie alle anderen E2-Images. Mittels Azup 2.2.7 von deinem PC aus.
Azup
Azup 2.2.7
@bonkel
HDMU 11904 oe 801 ... bugs:
-aio grab ... does not work ... (unknow stb type)
-HDMU info system ... does not work ... (E2 idle-spinner loop)
Ciao ...
@bonkel
HDMU 11904 oe 801 ... bugs:
-HDMU info system ... does not work ... (E2 idle-spinner loop)
Ciao ...
log?.....
aio-grab fixed
OK ... Thanks ;)
This is the UART log complete (AZBox Ultra): 5962
& when open the HDMU Center "Info System":
[Skin] Attribute not implemented: scrollbarMode value: showOnDemand
warning, skin is missing element label in <class 'Plugins.Extensions.HDMUCenter.HDMU_SystemInfos.HD MU_SystemInfos'>
[Skin] Attribute not implemented: scrollbarMode value: showOnDemand
[Skin] Attribute not implemented: scrollbarMode value: showOnDemand
main thread is non-idle! display spinner!
Ciao ...
sorry, using which version, finally??
sorry, using which version, finally??
Hi @morly
The before test refer to version 11904 oe 801 ...
If I have time ... I will test the new version 11906 oe 802 ... that from few time ... it's on server ! :)
Ciao ...
yeah - please test the new version - significant chances inside... ;)
yeah - please test the new version - significant chances inside... ;)
New version 11906 oe 802:
- aio grab (fixed) OK
Bug: Confirm issue on HDMU Center Info System !
GoodNight :cool:
Ciao ...
Hello.
First: it is very good and stable firmware, so thank You very much
second: how can I change back to TV mode from radio mode? How can I change audio track? (on other enigmas - yellow key)
third: there is a problem with ocasionally freezing screen for a half second - maybe it is kernel 3.9.2 or driver problem. This problem is the same in OpenATV image with 3.9.2 kernel.
Greetings,
marep
hallo
image ok tested:):):) azbox premium hd
openvpn is out ??
I installed manually CCcaminfo wrong 'on this image?
solutions?
Hola.la 11917 in system information discharge is 11906
macmanolo
23.12.2013, 18:36
HDMU 11917 oe 809 ... bug
-HDMU info system ... does not work ... (E2 idle-spinner loop), immer noch...
mfg
das Image gefällt mir sehr gut
THX
macmanolo
04.01.2014, 13:48
HDMU_11939_AzboxHD_OE_833_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11939_AzboxHD_OE_833_Flash.zip) instaliert und...
Das HDMU-Center hat in Menu Info system immer noch den gleichen fehler (E2 idle-spinner loop), da hilft nur hinten aus und an machen.
mfg
my internal hard drive no power off. always spins
macmanolo
04.01.2014, 17:31
The internal drive of my azbox if put into standby after 10 minutes of inactivity.
HDMU_11939_AzboxHD_OE_833_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11939_AzboxHD_OE_833_Flash.zip) instaliert und...
Das HDMU-Center hat in Menu Info system immer noch den gleichen fehler (E2 idle-spinner loop), da hilft nur hinten aus und an machen.
mfg
hast du das Image auf dem dom drauf ?
macmanolo
05.01.2014, 14:14
Jain, ich habe einem 8GB sdkarte in einen dom adapter.
Wird wie mit einen echten dom instaliert aber so als were einen cf karte gehandelt vileicht liegt es daran?
blueice_haller
06.01.2014, 11:33
Hallo,
ich habe gerade mit Azup das Image HDMU_11939_AzboxHD_OE_833_Flash (http://www.hdmedia-universe.com/board/pages.php?pageid=1&box=azboxhd) auf den 2GB DOM in der AZbox Premium HD Plus geflasht.
Es startet, im Display steht VFD READY! und über HDMI wird das Bootlogo (die Erde und in Brauntönen Gaswolken) angezeigt.
Aber der Einrichtungsassistent erscheint nicht.
Try to turn off the receiver by pressing the rear button ON/OFF ... and retry the boot for the first setup wizard !
blueice_haller
06.01.2014, 15:32
Funktioniert das HBBTV-Plugin (so wie im opena.tv-Image)?
probieren geht über studieren :)
Funktioniert das HBBTV-Plugin (so wie im opena.tv-Image)?
Da wirst du nicht viel Freude haben auf dieser Box mit HbbTV. So wie im OpenATV. Die Box ist einfach zu brustschwach dafür.
The internal drive of my azbox if put into standby after 10 minutes of inactivity.
The internal drive of my azbox if put standby in 10 minutes, not stop
I do not know if something is wrong because I have the image in usb.
but in all the image that I have in usb the internal drive standby after 10 minutes
macmanolo
11.01.2014, 12:24
HDMU_11939_AzboxHD_OE_833_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11939_AzboxHD_OE_833_Flash.zip) instaliert und...
Das HDMU-Center hat in Menu Info system immer noch den gleichen fehler (E2 idle-spinner loop), da hilft nur hinten aus und an machen.
mfg
Habe dem HDMU_11949_AzboxHD_OE_851_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11949_AzboxHD_OE_851_Flash.zip) geflash, keine settings engespielt alles rein sauber von null auf configuriert und der fehler besteht immer noch, dieses mal habe ich auch ( zum sicher sein) auch auf einen original DOM geflash und der resultat is der gleiche, ich kann nich sagen seit wan das pasiert aber am anfang, also mit der ersten versionen pasiete das nicht, eine idee woran das ligen kann?
mfg.
macmanolo
02.02.2014, 15:44
Habe heute mal herunprobiert mit de AZboxHD, und zur versuchen heraus zu finden warun der oben genante fehler aufkom, nun nach mehrere flash versuche mit versidene versionen bin auf folgendes gekommen:
Mit firm HDMU_11893_AzboxHD_OE_858_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11893_AzboxHD_OE_858_Flash.zip) funkzioniert alles... HDMU center - System Info OK, BonkelMediacenter OK, Wetter OK
Von firm HDMU_11906_AzboxHD_OE_802_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11906_AzboxHD_OE_802_Flash.zip) bis firm HDMU_11949_AzboxHD_OE_851_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11949_AzboxHD_OE_851_Flash.zip) HDMU Center - System Info nicht ok (kom dauer spinner), BonkelMediacenter WS, Wetter nicht ok (kom dauer spinner)
Habe Jetz 11893 in DOM gelassen da bei den alles gut leuft (auser den Cover in Mediacenter)
Lege log von WS bei.
mfg
macmanolo
13.02.2014, 21:49
Habe gerade gesehen das es neue image für den AZBoxHD gebt, möchte drauf aufmerksanmachen das es warseinlich was sief gegangen ist da die datei viel zu gross ist:
HDMU_12047_AzboxHD_OE_1206_Flash.zip
13-Feb-2014 20:42
123.27 MB
Ich kan das nicht probieren da ich an de AZ nur an wochenende dran komme, aber diesen wochenende bin ich auf eine reise und komme nicht dazu.
mfg
majid.209.mt
16.02.2014, 08:11
hi
for AZBOX ME please.
th@:ba226:
macmanolo
18.02.2014, 20:18
Bonkel, welchen Kernel benutz das image: HDMU_12047_AzboxHD_OE_1206_Flash.zip 13-Feb-2014 20:42 habe gelessen das diesen firm wieder zurück auf kernel 3.3.1 gegangen ist, ist das so, oder ist es bein kernel 3.9.2 geblieben?
mfg.
Dont work this soft = 123 MB ?????? file patch for Azbox verry BIG file
kernel 3.3.1 patch =49Mb
kernel 3.9.2 patch = 56 Mb
??????????= 123 Mb
Bonkel, welchen Kernel benutz das image: HDMU_12047_AzboxHD_OE_1206_Flash.zip 13-Feb-2014 20:42 habe gelessen das diesen firm wieder zurück auf kernel 3.3.1 gegangen ist, ist das so, oder ist es bein kernel 3.9.2 geblieben?
mfg.
ja zum test mal 3.3.1
Dont Arbeit dieser weichen = 123 MB??? Datei-Patch für Azbox verry BIG-Datei
Kernel-Patch 3.3.1 = 49MB
Kernel-Patch 3.9.2 = 56 Mb
????? = 123 Mb
macmanolo
19.02.2014, 21:45
Bonkel, etwas funkzioniert nicht mit der aufbau der images für de AZBoxHD, die images sind viel zur gross über 120MG, wie die leute hier http://www.hdmedia-universe.com/board/showthread.php?6012-image sagen können die nicht mit azup geflash werden, bitte wen du zeit hast werfe mal einen blick drauf.
Ich werde es am wochenende auch mal selber probieren aber wen es bei denen nicht funzioniert hat, denke ich wird es bei mir auch nicht funzen.
mfg
Haben wir schon gemerkt das da irgendwas faul ist,
Bonkel schaut sich die Sache an , wenner bissl Luft hat.
Ja, so ein großes Image läßt sich nicht mehr flashen. Genau dieses Problem hatte auch Captain von OpenATV Anfangs für das 4.0 Image mit dem 3.9.2 Kernel. Mit dem 3.3.1 Kernel funzte es dann aber.
OpenATV 4.0 kernel 3.3.1 AzboxHD=48.465 KB legal Image
http://images.mynonpublic.com/openatv/beta/index.php?open=azboxhd
ravemaster
21.02.2014, 12:48
@bonkel
Gibt es schon was neues wegen dem zu großen Image? :rolleyes:
Ich hab am WE mal eines der älteren Testen können und es hat mir bis auf die Keymap gut gefallen. Wäre super, wenn es auch ein funktionierendes 3.3.1er Kernelimage gäbe.
@ bonkel
Check the build environment ... on the cramfs there is an origin code of sources & include data of cross compiling system ! :)
Ciao ...
mh i see that captain use gcc 4.5.1??
or what is the problem, i dont see a mistake in image build, so i dont know why its so big,
we use gcc4.8.2 and i will not downgrade it to 4.5.1
firmware is BIG,dont work
hi! i have installed Hdmu firmware in pen usb , but driver pl2303 is not installed, : cat /proc/bus/usb/devices
T: Bus=01 Lev=03 Prnt=05 Port=01 Cnt=01 Dev#= 9 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=067b ProdID=2303 Rev= 3.00
S: Manufacturer=Prolific Technology Inc.
S: Product=USB-Serial Controller
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 10 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Help me ,what this is the way for install driver pl2303 in my image in pen ?
thanks for help and for this nice image
macmanolo
26.02.2014, 20:43
mh i see that captain use gcc 4.5.1??
or what is the problem, i dont see a mistake in image build, so i dont know why its so big,
we use gcc4.8.2 and i will not downgrade it to 4.5.1
¿Ist da was neuers mit der images für den AZBoxHD?
¿können wir dem nächts auf neue images hoffen?
¿Oder ist da iergend wie ein grosses problem aufgetauch?
mfg.
zu dem stand hat sich nix geändert...ich seh wie gesagt keinen fehler und ich werde das gcc nich downgraden
Gerade mal das HDMU_12049_AzboxHD_OE_1218_Flash.zip auf eine azbox hd premium geflasht.
opkg und vsftpd liefen nicht.
root@azboxhd:/# opkg update
Collected errors:
* opkg_conf_load: Could not create lock file /var/lib/opkg/lock: No such file o
r directory.
Lösung: mkdir /var/lib/opkg/
[R] Verbindung herstellen zu 192.168.0.161 -> IP=192.168.0.161 PORT=21
[R] Verbunden mit 192.168.0.161
[R] 500 OOPS: vsftpd: not found: directory given in 'secure_chroot_dir':/var/share/empty
[R] Verbindung fehlgeschlagen
Lösung: opkg install vsftpd
Kann da beim flashen etwas schief gelaufen sein oder liegts am image?
macmanolo
28.02.2014, 19:04
Ich glaube das kann nicht am firm liegen da man es wegen hiergend einen fehler in der grösse der fiele nicht flashen kann.
habe es geflasht :-) Aber ist meine erste azbox, kann mich auch nicht sonderlich mit den Kisten anfreunden *g*
ravemaster
28.02.2014, 19:06
Konntest Du das Image mit dieser Größe überhaupt flashen?
In der Fehlermeldung stand doch das Problem, denke mal Flash zu klein, steck einen USB Stick an und installier es darauf.
macmanolo
28.02.2014, 19:22
Wie du hier http://www.hdmedia-universe.com/board/showthread.php?5167-Image-online&p=70789&viewfull=1#post70789 sehen kanst, ich habe es versuch auf einen pendrive im USB zur flashen, aber die datei ist zur gross und bricht bein 69,5% ab, die probe habe ich vor einen viertelstunde gemacht :eek:
mfg
Don't make believe the wrong things ... to people! :mad:
Who has tried ... has installed on DOM more larger or pendrive with using scripts to change the size of the partitions for it working !
Iam not familar with this stbs, so calm down!
Image flashed but some things missing, e.g. opkg, vsftp, webinterface dont work. Some other stuff too i guess. But stb booted and operated.
Installed now HDMU_11949_AzboxHD_OE_851_Flash, work for me. Image has half the size than newer ones.
If youre the azbox expert please explain how to do, and stop spamming :-)
Gerade mal das HDMU_12049_AzboxHD_OE_1218_Flash.zip auf eine azbox hd premium geflasht.
opkg und vsftpd liefen nicht.
root@azboxhd:/# opkg update
Collected errors:
* opkg_conf_load: Could not create lock file /var/lib/opkg/lock: No such file o
r directory.
Lösung: mkdir /var/lib/opkg/
[R] Verbindung herstellen zu 192.168.0.161 -> IP=192.168.0.161 PORT=21
[R] Verbunden mit 192.168.0.161
[R] 500 OOPS: vsftpd: not found: directory given in 'secure_chroot_dir':/var/share/empty
[R] Verbindung fehlgeschlagen
Lösung: opkg install vsftpd
Kann da beim flashen etwas schief gelaufen sein oder liegts am image?
Iam not familar with this stbs, so calm down!
Image flashed but some things missing, e.g. opkg, vsftp, webinterface dont work. Some other stuff too i guess. But stb booted and operated.
Installed now HDMU_11949_AzboxHD_OE_851_Flash, work for me. Image has half the size than newer ones.
If youre the azbox expert please explain how to do, and stop spamming :-)
I do spamming?
My friend ... are years that are behind the AZBox's world ... and everything I've learned I sent to the community!
From your statements, users are thinking that the new versions (12047 and 12049) were you able to install them!
Only now I read that you're trying the 11949 version that can be installed by all of us!
Saluti ...
First, we are not friends.
Second, i installed the HDMU_12049_AzboxHD_OE_1218_Flash too, but with errors. Try yourself if you dont believe. Choose USB & hit update Kernel/E2, when the error Message appears (near 68%) klick ok and be patient, dont abort, azup will continue. Stb will reboot, be patient again, no bootlogo, nothing in vfd, after a few minutes spinner and after that start assistand will appear.
STB boot and basics are running fine, but as said, its corrupted. Could be fixed manually, but that dont make sense, the fault is somewhere else.
Sorry ... is correct ... we are not friends!
Good test with your AZBox ...
@redoom
... ist das Image im Flash danach noch voll ok ?
...hab da irgendwo gelesen..finde es aber leider nicht mehr...das es sich danach bzgl. der Bildeinstellungen usw. irgendwie "komisch" verhält..
Nein das 12049 ist nicht ok, azup bricht anscheinend ab bevor es komplett installiert ist. Reicht zum booten, hatte opkg und ftp gefixt, danach dann festgestellt das opkg keine installierten pakete, bzw nur die nach dem fix installieren auflistet. Danach dachte ich mir dann warum das leben schwer machen, ist nicht meine box. Also das 11949 geflasht und eingerichtet.
THX @redoom
..meine Frage bezog sich zwar auf das nachträgliche Verhalten eines schon im Flash befindlichen Image ..nachdem auf dem USB-Stick das aktuelle HDMU installiert wurde...aber ist nicht so wichtig...war eher ne theoretische Frage,da ich praktisch da eh nicht mitreden kann...
Im Flash war irgend ein Fremdimage, habe nach dem gebastel nicht wieder darauf zurück gegriffen. Stick rausgezogen und die Kiste ist mit der IP im Display stehen geblieben. dann das HDMU in den Flash gepappt und gut war.
Ein opkg-upgrade unter 11949 führt zu einer box die nicht mehr bootet da die installation von base-files - 3.0.14-r11958 - 3.0.14-r12052 hängen bleibt.
Wer trotzdem ein aktuelles image haben möchte kann mal den befehl per telnet absetzen:
Vorher opkg update
opkg install libav enigma2-plugin-extensions-mediascanner libcom-err2 tslib-conf libavformat53 liborc-test-0.4-0 openssl libavdevice53 dbus-1 modutils-initscripts libavutil51 enigma2-plugin-systemplugins-fastscan enigma2-plugin-systemplugins-hotplug libdbus-1-3 tzdata openssl-conf enigma2-plugin-systemplugins-cablescan libdvdread4 libts-1.0-0 dropbear curl enigma2-plugin-extensions-cutlisteditor enigma2-plugin-systemplugins-positionersetup enigma2-hdmu libavcodec53 enigma2-fonts base-passwd e2fsprogs-e2fsck kmod libdvdnav4 enigma2-plugin-systemplugins-videomode libswscale2 libext2fs2 enigma2-plugin-systemplugins-softwaremanager libavfilter2 tuxbox-common libsoup-2.4 libcurl4 enigma2 liborc-0.4-0 boxmodel enigma2-plugin-systemplugins-networkwizard file libglib-2.0-0 libtuxtxt32bpp0 libtasn1-6 netbase e2fsprogs-tune2fs enigma2-plugin-systemplugins-skinselector kernel-module-boxmodel zram e2fsprogs-mke2fs libpostproc52 aio-grab enigma2-plugin-extensions-graphmultiepg libtuxtxt0 libe2p2 enigma2-plugin-systemplugins-satfinder libfreetype6 enigma2-plugin-systemplugins-videotune
Ist es eigentlich normal das die Umschaltzeiten bei der Box so mies sind?
Was verstehst du unter mies?
Die schnellsten Boxen sind es nicht. Aber direkt als mies würde ich das auch nicht sehen.
[QUOTE=zeini;70814]Was verstehst du unter mies?/QUOTE]
3-5 Sekunden bei FTA
Nun 2-4 Sekunden habe ich auch. Mein nagelneuer 4K TV hat übrigens auch so lange Umschaltzeiten. :(
2-4 Sekunden ist nicht so schön.....und das bei FTA. :(
macmanolo
01.03.2014, 15:08
Mit HDMU 11893_856 Starten vom hinteren knopf bist image vom Sat mit Oscam erscheint 1 minute und 18 sekunden (mit starupvideo von HDMU), umschaltzeiten bei FTA sender in SD qualität etwa 1 sekunde bei HD qualität kappe 2 sekunde, versucht mit ARD/ZDF.
mfg
sofrenic
23.03.2014, 14:14
Ich kann meine WiFi-Treiber für AZBox HD nicht finden (HDMU 07.01.2014)
macmanolo
27.03.2014, 13:30
*Bonkel, wie geths mit den AZBoxHD, wierd es neuer images geben oder is diese leitung in standby?
mfg.
blueice_haller
18.04.2014, 00:07
Hallo,
ich habe einen 2 GB DOM und bei mir kommt bei HDMU_12049_AzboxHD_OE_1218_Flash (http://www.hdmedia-universe.com/board/pages.php?pageid=1&box=azboxhd) die Fehlermeldung dass das Image zu groß sei und ich USB nutzen soll.
Ich habe es gerade mit einem 2 GB USB Stick getestet. Erst Only Kernel und dann Device USB und dann kam could not write file und danach An error occured while copying the kernel 3 unsuccessful attempts oder ich soll einen anderen Stick verwenden weil er möglicherweise zu langsam ist.
Auf dem USB Stick wurden 4 Partitionen angelegt.
Ich habe nun mehrere Möglichkeiten:
a) Ich bitte um ein Image für DOM
b) Ich installiere ein anderes Image z.B. openATV mit Format Extended Partition, formatiere die Partitionen und installiere dann HDMU ohne dem Format Extended Partition. Ich erhoffe mir dass das Image dann in den DOM passt.
c) eine Anleitung wie ich die patch.e2 entpacken, anpassen und packen kann. Ich habe ein Tool gefunden: unpack_e2.c.zip
Flashe das HDMU 11949 Image (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11949_AzboxHD_OE_851_Flash.zip). Und mach dann ein Onlineupdate.
Die 12047 und 12049 dürften von der Größe her tatsächlich nicht passen. Da ist wohl was beim Bauen daneben gegangen.
blueice_haller
18.04.2014, 12:15
Danke. Und dann bin ich auf dem selben Stand? Beim ersten Versuch ist bei den base-files über eine halbe Stunde nichts passiert.
Das habe ich dann abgebrochen und nun kommt VFD READY! und im TV BOOTING.... Ich flashe nochmal und bleibe erstmal bei 11949.
Wo kann ich die Gelbe Taste auf Tonspur (anstatt Mediacenter) umstellen?
Und wo kann ich den Lüfter im Standby ausschalten?
enigma2-plugin-systemplugins-rtisys_git13+e368824-r16_azboxhd.ipk
enigma2-plugin-extensions-infopanel_3.0+git18107+753a705-r3_azboxhd.ipk
Warum geht meine HDD nicht in den Standby?
Ich weiß jetzt warum das Image so groß ist:
HDMU_12049_AzboxHD_OE_1218_Flash/cram.img/usr/src/kernel/ <-- Hier liegen viele Dateien
HDMU_11949_AzboxHD_OE_851_Flash/cram.img/usr/src/ <-- Dieses Verzeichnis ist leer
HDMU_12302 AzboxHD ist Top bis auf Radio.:sm49::sm49:
neustes image schon getestet?
neustes image schon getestet?
Yes ... it works [12316 oe 1344]!
I could not try everything on AZ Ultra HD version ... :)
I had some trouble finding the right combination for the frequency of the card reader with oscam8837 and TivuSat N3 card (the only combination that works is cardmhz = 368 mhz = 500) while other from feed:ymod not SC init, 3c ok (always) ... but the ecm time is up approximately 650 ms and occasionally produces video freeze!
The zap time (approximately):
crypt to crypt = 6 s
crypt to fta = 3 s
fta to fta = 2 s
- HDMU Media Center = OK [AVI-MKV-Mp3 simple file play test] and TS play from CIFS Net Mount VodafoneTV(DVB-T) recordings storage device !
Ciao & Thanks
macmanolo
23.04.2014, 15:41
Ja, heute kurzt image "HDMU_12302_AzboxHD_OE_1343_Flash" getestet und alles was ich normaleweise benutze leuft wie es sein sollte, für mich nach der "HDMU_11893_AzboxHD_OE_858_Flash" das beste image.
mfg.
PD. habe gesehen das es wieder eine neuer imege giebst werde es gleich mal einspielen und zur sehen wie dieses leuft.
PD2. Online update gemacht und alles leuft weiter so gut wie vorher...
sofrenic
23.04.2014, 21:24
HDMU_12316_AzboxHD_OE_1344_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_12316_AzboxHD_OE_1344_Flash.zip) WIfI NOT OK
HDMU_12302_AzboxHD_OE_1343_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_12302_AzboxHD_OE_1343_Flash.zip) WiFi not OK
Can't Connect to the Internet
nothing changed with wifi..
sofrenic
24.04.2014, 22:34
Could not connect to the router. Version 851 is ok. Keymap for audio subtitle fix is stil required, hooked him
blueice_haller
21.05.2014, 00:59
I was wondering that after installing RTi-SYS Plugin I can't control the fan of my premium+ (Open Webif > Receiver-Informationen > Modell).
I'm new in developing python plugins and studied the code from RTi-SYS https://github.com/OpenAZBox/RTi-SYS.
In lines 307, 431, 446 and 575 of https://github.com/OpenAZBox/RTi-SYS/blob/master/plugin.py it tries to determine and assign the model type. Example line 307:
hw_type = HardwareInfo().get_device_name()
if hw_type == "me" or hw_type == "minime" :
self.LEDtimeTimer.callback.append(self.updateLED)
if hw_type == "minime" :
self.RtiminimeTimer.callback.append(self.updateCR)
elif hw_type == 'elite' or hw_type == 'premium' or hw_type == 'premium+' or hw_type == 'ultra' :
self.LEDtimeTimer.callback.append(self.updateLEDHD )
if hw_type == 'ultra' or hw_type == 'premium+':
self.FANtimeTimer.callback.append(self.updateFAN)
This is later important to get the correct entries in Einstellungen > System > ...
def Plugins(**kwargs):
hw_type = HardwareInfo().get_device_name()
if hw_type == 'ultra' or hw_type == 'premium+':
return [
PluginDescriptor(name="FanCtrl", description="FAN Controll", where = PluginDescriptor.WHERE_MENU, fnc=startSetup),
PluginDescriptor(name="AVp_setup", description="scan mode & interlaced algo", where = PluginDescriptor.WHERE_MENU, fnc=startSetup2),
PluginDescriptor(where=[PluginDescriptor.WHERE_SESSIONSTART], fnc=sessionstart)
]
elif hw_type == 'minime':
return [
PluginDescriptor(name="CRClock_setup", description="CR set freq", where = PluginDescriptor.WHERE_MENU, fnc=startSetup1),
PluginDescriptor(name="AVp_setup", description="scan mode & interlaced algo", where = PluginDescriptor.WHERE_MENU, fnc=startSetup2),
PluginDescriptor(where=[PluginDescriptor.WHERE_SESSIONSTART], fnc=sessionstart)
]
else:
return [
PluginDescriptor(name="AVp_setup", description="scan mode & interlaced algo", where = PluginDescriptor.WHERE_MENU, fnc=startSetup2),
PluginDescriptor(where=[PluginDescriptor.WHERE_SESSIONSTART], fnc=sessionstart)
]
Because I only get the [A/V settings +] entry something went wrong: I think that it runs in the last else in line 588.
Because I dont't know where to find the missing function HardwareInfo(): hw_type = HardwareInfo().get_device_name() I easily assign it manually to hw_type = premium+ 4 times in the lines 307, 431, 446 and 575.
Does anybody know an alternative to determine this? Which function does Open Webif use to determines it?
And yes, if I change the code, delete the plugin.pyo and restart the box I have also the entry [Fan Set] in OSD and can change anything.
I have tested it and it works.
That what I heard then was the HDD (ST3500630AS) which goes in standby after some minutes with my init-script (http://www.hdmedia-universe.com/board/showthread.php?5167-Image-online&p=81053&viewfull=1#post81053).[/B]
Brauch kurze Hilfe,
das Image besteht aus cram.img und kernel.img
Wie können die auf welche Partition geflasht werden (via telnet)??
Wohl besser nicht via dd, oder?
macmanolo
12.06.2014, 21:48
Wird nomaleweise mit en eigenes program geflash "AzUp 2.2.7" ist ein windows program :-( früer gabs einen in java aber der funzioniert jetz nicht mehr?
mfg
hab ja das Ding entpackt und die beiden Files liegen, muss nur wissen welches mtd wofür ist (vermute kernel=mtd4 und rootfs=mtd0)
macmanolo
12.06.2014, 22:03
Morgen nachmitag komme ich an den az dran, dan kann ich ja nachsehen was du mir sagts.
mfg
Interessant wäre wo der Kernel sitzt und wo rootfs.
Dabei könnte helfen:
cat /proc/cmdline
Und eben wie die Dinger dann geflasht werden ;)
Die "alten" Azboxen (Premium HD, Premium HD+, Elite HD und Ultra HD) sind Zicken beim flashen. Ich rate davon ab, das mit deinem Tool zu flashen. Beim Neuflashen wurden schon viele Boxen in die ewigen Jagdgründe geschickt.
Derzeit gibt es nur ein Tool, Azup 2.2.7, mit welchem man alle Images flashen kann. Es gab sicher 5 verschiedene Vorprodukte dieses Flashtools. Und das wurde immer nur deshalb erneuert, weil mit einem neuen Image meist mit neuem Kernel, das vorige Tool nicht mehr funzte und die Box nur mehr mittels JTAG wiederbelebt werden konnte, falls man mit dem "alten" Flashtool flashte.
Nichts desto trotz aber mal deine gewünschte Abfrage
root@azboxhd:~# cat /proc/cmdline
mem=107m console=ttyS0,115200
Verstanden - Danke, dann lass ich das mal :)
Also Box kommt rein aber ohne Flash/Backup Support
macmanolo
13.06.2014, 10:12
Backup wurde aber schon eine gutte sache sein, da es keine utility dafür giebt.
Auch wen man das mit azup flashen müste
dann mach mir mal von jeder mtd einen dd dump (bitte einfach mtd0-mtdx benennen) und lad mir diese hoch, teste dann was...
macmanolo
13.06.2014, 12:52
dann mach mir mal von jeder mtd einen dd dump (bitte einfach mtd0-mtdx benennen) und lad mir diese hoch, teste dann was...
OK, jetz sietze ich vor den AzBoxHD wie sollte ich das was du meints machen?
Von Linux aus? von Telnet?, mit ftp programm?
mfg
blueice_haller
29.06.2014, 13:34
Hallo,
wo wird denn festgelegt wie die Festplatte gemountet wird? In /etc/fstab steht nichts davon:
rootfs / auto defaults 1 1
proc /proc proc defaults 0 0
devpts /dev/pts devpts mode=0620,gid=5 0 0
usbdevfs /proc/bus/usb usbdevfs noauto 0 0
tmpfs /var/volatile tmpfs defaults 0 0
Ausgabe von mount: /dev/hdb1 on /media/hdb1 type ext3 (rw,relatime,errors=continue,user_xattr,barrier=1, data=ordered)
Ausgabe von blkid:
/dev/hdb1: UUID="d0e57e92-dff5-407f-aca2-1f9fa5d69e53" TYPE="ext3"
/dev/hda2: UUID="482d897c-e88e-4ec4-a326-813ddff7de47" TYPE="ext2"
/dev/hda1: UUID="585544f9-7062-4e23-9002-2f83ee5e805d" TYPE="ext3"
/dev/hda3: UUID="6a6444b1-f689-4b06-a97a-2f7b54e79fed" TYPE="swap"
/dev/hda5: UUID="fb4bb225-89ff-4c8f-a527-b10832e16a88" TYPE="ext3"
/dev/mtdblock/4: LABEL="MIPS_LINUX_XRPC" TYPE="romfs"
/dev/mtdblock/3: LABEL="YAMON_XRPC" TYPE="romfs"
Ziel: Ich möchte dass der Symlink /media/hdd wieder funktioniert. Ich könnte das auch in einem Startskript hinterlegen.
Ich habe jetzt einen Eintrag in der /etc/fstab erstellt:
UUID=d0e57e92-dff5-407f-aca2-1f9fa5d69e53 /media/hdd ext3 defaults 0 0
Irgendwas stimmt mit dem nfsserver nicht:
/etc/init.d/nfsserver restart
stopping mountd: done
stopping nfsd: done
starting 8 nfsd kernel threads: rpc.nfsd: writing fd to kernel failed: errno 146 (Connection refused)
rpc.nfsd: unable to set any sockets for nfsd
opkg install --force-reinstall rpcbind
Downloading http://hdmu.de/mipsv2/azboxhd/mips32el/rpcbind_0.2.1-r0_mips32el.ipk.
Reinstalling rpcbind (0.2.1-r0) on root.
Stopping rpcbind daemon...
not running.
update-rc.d: /etc/init.d/rpcbind exists during rc.d purge (continuing)
Removing any system startup links for rpcbind ...
/etc/rc0.d/K60rpcbind
/etc/rc1.d/K60rpcbind
/etc/rc2.d/S12rpcbind
/etc/rc3.d/S12rpcbind
/etc/rc4.d/S12rpcbind
/etc/rc5.d/S12rpcbind
/etc/rc6.d/K60rpcbind
Running useradd commands...
NOTE: Performing useradd with [ --system --no-create-home --shell /bin/false --user-group rpc] and 10 times of retry
WARNING: user rpc already exists, not re-creating it
Configuring rpcbind.
Adding system startup for /etc/init.d/rpcbind.
Starting rpcbind daemon...rpcbind: fork failed: No such device
done.
macmanolo
29.06.2014, 19:50
Schau mal hier wegen die platte http://www.hdmedia-universe.com/board/showthread.php?2013-Festplatte-initialisieren-oder-wie-bekomme-ich-meine-HDD-eingebunden
mfg
blueice_haller
30.06.2014, 07:46
Hallo macmanolo,
es hat bereits geklappt mit dem einbinden über /etc/fstab aber der nfsserver startet nicht.
Ich habe in einem Forum gelesen dass es mit rpcbind_0.2.1-r4 wieder funktioniert aber das ist noch nicht auf dem Feed.
the problem with the internal hard drive with not go in standby Corrected?
blueice_haller
30.06.2014, 21:08
Hello kapios,
my solution for this problem:
1. create/edit file: /etc/init.d/hdparm
#!/bin/sh
ROOTHDD=/dev/hda
MOVIEHDD=/dev/hdb
ALLHDD="$ROOTHDD $MOVIEHDD"
STANDBYTIMEOUT=180 # 180 means 15 minutes
set -e
case "$1" in
start)
$0 setstandbytimeout
;;
setstandbytimeout)
hdparm -S $STANDBYTIMEOUT $MOVIEHDD
;;
status)
hdparm -C $ALLHDD
;;
nostandby)
hdparm -S 0 $MOVIEHDD
;;
*)
echo "Usage: $0 {status|setstandbytimeout|nostandby}"
exit 1
;;
esac
exit 0
2. Give execute rights
chmod +x /etc/init.d/hdparm
3. Create symlink to execute the script at boot time (I don't know if the runlevel 08 is optimal):
ln -s /etc/init.d/hdparm /etc/rcS.d/S08hdparm
4. For testing you can execute the script:
/etc/init.d/hdparm start
Hi
HDMU_12690_AzboxHD_OE_1595
... Few Test to keep the memory ...
- HDMU Media Center (Web Radio fixed)
- WiFi WLAN (not fixed)
- Switch TV/Radio channel list (not fixed)
Ciao ...
ravemaster
09.08.2014, 06:03
@bonkel
Könntest du dir bitte mal das Problem mit dem HDD-Standby ansehen? Die läuft immer durch. Ich nutze das Image auf meiner HD. Es ist um einiges speicherschonender als andere.
Es nervt aber, wenn die HDD immer durchläuft (Box im Schlafzimmer) :eek:
Achja und das Onlineupdate funktioniert nicht richtig.
7898
Besten Dank
Schau doch mal ob die Befehle sdparm und hdparm vorhanden sind und ob du damit die HDD schlafen legen kannst
wieso funktioniert das online update nicht richtig? die meldung ist absichtlich da
wenn was schief geht..........
und wie soll die hdd in den standby gehen, wenn das image drauf läuft?
@bonkel
Test on AZBultra HDMU 12823 OE 1642 ... default HDMU config and definition xml ... without any other plugins !
With the latest merge from OpenPLi (from last week at now) ... with last "T2-Auto scan" code changes ... after an automatic search with the DVB-T tuner USB dongle (Aver Volar Green HD "AF9035") ... the channel selection always returns a message "Tuner failed" on any digital terrestrial channels stored !
This does not happen by making a manual single DVB-T scan by frequency or channel number !
Make it known to the Team OpenPLi!
Thank you & Ciao ...
Welche Plugin, um den Lüfter zu steuern, weil ich versuchte, ein paar und keiner von ihnen zu arbeiten. Hat jemand überprüft.
ravemaster
09.08.2014, 22:50
Das mit dem Update ist nun klar, aber das Image läuft doch im Dom und nicht auf der HDD. Die geht doch auch bei anderen Images in Standby.
blueice_haller
10.08.2014, 11:01
@ravemaster: Hast Du meinen Beitrag mit Skript für HDD Standby (http://www.hdmedia-universe.com/board/showthread.php?5167-Image-online&p=81053&viewfull=1#post81053) nicht gelesen? Dein Satz in #174 (http://www.hdmedia-universe.com/board/showthread.php?5167-Image-online&p=83528&viewfull=1#post83528) wurde wahrscheinlich anders interpretiert: mit HD meinst Du nicht HDD sondern das Modell. Und es ist klar sobald etwas auf die HDD zugreift fährt sie wieder hoch.
@lucek: Did you read my reply about controlling the FAN e.g. off in standby (http://www.hdmedia-universe.com/board/showthread.php?5167-Image-online&p=78242&viewfull=1#post78242)?
Es wäre nett wenn diese einzug in das nächste Image halten würden. Danke.
ravemaster
10.08.2014, 21:14
OK. Ich meine eine PremiumHD ( die Box). Das die eingebaute Festplatte immer läuft, ist denk ich mal ein Imagefehler. Das machen ja auch andere Images nicht. Ich hab auch Deinen Beitrag gelesen. Das ist dann maximal ein Workaraound und keine Lösung des Problems. Nichts für ungut, ich mag dieses Image, aber die Festplatte sollte im normalen TV-Betrieb nicht immer laufen. Die ist für Timeshift, Aufnahmen und Wiedergabe gedacht.
du hast meine frage nicht beantwortet, deswegen jetzt noch mehr
ist sdparm und/oder hdparm auf der Box vorhanden?
kannst du per telnet die HDD damit zum schlafen bringen?
geht die HDD nie aus?
andere HDD mal getestet?
ravemaster
11.08.2014, 13:44
Sorry santa.
1.) hdparm ist vorhanden.
2.) Mit hdparm lässt sich HDD in Standby versetzen. (hdparm -y /dev/hdb1)
3.) Sobald die HDD mal erweckt wurde, geht sie nicht wieder aus.
4.) Test mit anderer HDD nicht durchgeführt. Die funktioniert super (auch mit anderen Images). :D
Ich hoffe, dass konnte helfen.
@blueice_haller (http://www.hdmedia-universe.com/board/member.php?6132-blueice_haller)
I used a plugin rtisys standby and works :)
Maybe in the next images will be repaired.
blueice_haller
12.08.2014, 23:21
Hallo ravemaster,
-y hält nur bis zum nächsten Zugriff.
-S setzt die Standby-Zeit des Gerätes. Nach der eingestellten Zeit fährt die Festplatte in den Ruhezustand (entspricht -y). Ein Wert von 0 schaltet diese Funktion aus, maximal bis 255. Die Einteilung ist nicht linear, man muss etwas probieren um auf die gewünschte Zeit zu kommen.
-y setzt das Laufwerk sofort in den Standby Modus, die Spindel stoppt dabei. Bei Zugriffen wacht es automatisch wieder auf.Die Standby-Zeit wird nach einem Neustart wieder zurckgesetzt, das heißt die HDD schaltet sich nicht aus. Aus diesem Grund habe ich ein init-Skript geschrieben welches beim booten die Standby-Zeit mit -S setzt.
ravemaster
13.08.2014, 04:07
@blueice_haller
Vielen Dank. Ich werde das Script als Workaround einsezten. Vielleicht wird das ja im Image auch noch behoben. :)
macmanolo
15.08.2014, 15:50
Habe heute OnlineUpdate gemacht und sehe das der platz im Flash völig voll benutz ist obwohl keine extra plugins instaliert sind, ist das normal?
7955
mfg
Neu flashen und nochmal.schauen. Hab paar Sachen geupdated
ravemaster
15.08.2014, 16:33
@bonkel
Hast du zufällig auch was beim Festplattenstandby geändert? :rolleyes:
Bin auch gerade am neu flashen, wegen Speichermangel nach dem Update, dann könnte ich das gleich testen. :)
ravemaster
15.08.2014, 16:44
Auch wenn das jetzt lästig erscheint, aber kommt da noch eine Änderung? Wäre super, wenn die HDD wieder in Standby gehen würde.
Im Moment hab ich andere Sorgen
ravemaster
15.08.2014, 17:02
Ok.
Mit dem letzten Image vom 14. lassen sich keine Plugins mehr installieren. Opkg update hat nichts gebracht.
7956
macmanolo
15.08.2014, 17:51
So,habe den platzmangel gelöscht aber glaube das ist kein general lössung.
Habe einen sd-adapter als DOM mit eine 8GB sd karte, die hate eine partition für images von 170MB (nehme an das ist der platz das der original DOM von 250 MB für das image bereitstellt, und das ist mitleweile zur benig.
Habe lätzters image mit azup228 im DOM neu instaliert mit "Format Extended Partition" angekreuzt und sehe da jetz habe ich eine partition von 325 MB und nur 53% besetz, das image benutz ohne plugins 173MB deswegen war ja kein platz mehr da.
Die lössung besteht entweder mann erweiter der DOM oder man instaliert das image im einen pendrive dan gehts.
mfg
macmanolo
18.08.2014, 13:13
Habe weitere tests gemacht, und bin auf folgendes gestossen, wen ich azup2.2.7 benutze dan wierd der platz im DOM sehr knap 7987 wie man sehen kann ist kein freie speicher mehr da, also man kan nicht mehr instalieren keine plugins etc...
Wen ich aber azup2.2.8 benutze dan habe ich doch eine menge freie speicher 7988
Auf einen USB-pendrive mit azup2.2.7 hat man doch noch platz 7989 sogar nach einen OnLineUpdate wie man sehen kann.
Und so habe ich beiden azup gehab2.2.7 7985 und 2.2.8 7986
Also bin ich zun abschluss gekommen das man azup2.2.8 benutzen sollte wen mann einen nicht original DOM hat, damit sollte man keine speicher probleme mehr haben, woran das liegt kann ich nicht sagen aber bei mir hats so geklapt.
mfg
ravemaster
19.08.2014, 04:33
AzUp 2.2.8 überprüft die größe des DOM's und teilt bei einem größeren als dem Standard (256MB) die Partitionen anders auf. Darum kann man so oder so 2.2.8 verwenden.
macmanolo
20.08.2014, 23:31
AzUp 2.2.8 überprüft die größe des DOM's und teilt bei einem größeren als dem Standard (256MB) die Partitionen anders auf. Darum kann man so oder so 2.2.8 verwenden.
Leider ist der AzUp 2.2.8 nicht so tool wie ich es mir gedach hatte .
Wen mann die AzUp 2.2.8 benutz hat man zwar mehr platz aber dafür kann man nicht mehr des multiboot benutzen :mad:
Eine idee warum das so ist?
mfg
ravemaster
21.08.2014, 04:27
Nein, leider nicht. Ich nutze kein Multiboot bei der PremiumHD. Der Boot über USB dauert mir einfach zu lange.
blueice_haller
30.08.2014, 12:17
Kann bitte jemand AzUp 2.2.8 in das UploadCenter (http://www.hdmedia-universe.com/board/UploadCenter.php) stellen? myazbox.de ist momentan nicht verfügbar.
Hat sich erledigt, hier ist es: AzUp 2.2.8 (http://www.hdmedia-universe.com/board/UploadCenter.php?do=download&downloadid=70)
Ich habe nun AzUp 2.2.8 HDMU_12927_AzboxHD_OE_1763_Flash geflasht.
Leider bekomme ich den nfsserver nicht zum laufen, siehe auch Post 168 (http://www.hdmedia-universe.com/board/showthread.php?5167-Image-online&p=80982&viewfull=1#post80982):
root@azboxhd:~# /etc/init.d/nfsserver restart
stopping mountd: done
stopping nfsd: done
starting 8 nfsd kernel threads: rpc.nfsd: writing fd to kernel failed: errno 146 (Connection refused)
rpc.nfsd: unable to set any sockets for nfsd
root@azboxhd:~# /etc/init.d/rpcbind start
Starting rpcbind daemon...done.
root@azboxhd:~# rpcbind: fork failed: No such device
root@azboxhd:~# opkg install portmap
Unknown package 'portmap'.
Collected errors:
* opkg_install_cmd: Cannot install package portmap.
root@azboxhd:~#
Folgende Pakete habe ich irgendwo gefunden: portmap-utils_6.0-r7_mips32el.ipk portmap_6.0-r7_mips32el.ipk
@bonkel: Kann es sein dass das NFS beim komplilieren des Kernel nicht ausgewählt ist? Kannst Du das bitte wieder einbauen? Oder verwendest Du den fertigen binären Kernel z.B. http://hdmu.de/mipsv2/azboxhd/azboxhd/kernel-image-3.3.1-opensat_3.3.1-r3.2_azboxhd.ipk und hast darauf keinen Einfluss?
An welchen Entwickler/Forum/Nutzer muss ich mich wenden?
blueice_haller
01.02.2015, 15:38
Hallo, ich wollte gerade das letzte Image HDMU_13668_AzboxHD_OE_1927_Flash (http://www.hdmedia-universe.com/board/pages.php?pageid=1&box=azboxhd) auf meinen 2GB DOM installieren, doch es kommt die Fehlermeldung: 14:32:35 > Image Size = 146 M -> Image too big
Hat das hiermit zu tun?
Dafür müste Bonkel der alte Gstreamer benutzen und ich glaube das wierd woll nicht sein.
mfg
Wenn ja wie groß muss der USB Stick sein?
macmanolo
01.02.2015, 15:45
Mit einen 1GB ist genug musst aber in multiboot instalieren und mit 2GB dom geht nicht ohne weiteres.
mfg.
blueice_haller
01.02.2015, 15:54
Ich habe nur einen USB Stick mit 8GB. Soll ich es dort installieren?
Ich habe es auf dem 8GB USB Stick installiert und es tritt das selbe Problem wie mit dem openATV Image auf:
Wenn man auf Radio schaltet dann dreht sich das HDMU-Logo links oben und man muss die Box neu starten.
Jemand hat dort einen Fix gebaut, bei welchem man enigma2 stoppt, /usr/bin/enigma2 austauscht und enigma2 wieder startet: Radio fix for openATV 4.2
No image azboxhd , azboxme , azboxminime. Was ist der grund?
http://www.hdmedia-universe.com/board/pages.php?pageid=1&box=azboxhd
Azbox Unterstützung wird fortgesetzt?
Ja. Baut im Moment nur nicht
..tja,der Frage schließe ich mich an.... baut das HDMU immer noch nicht? ...die "Iberer" und "Lateinamerikaner " laufen Euch sonst davon !!
...was ich so an diesem Forum "Liebe" sind die sehr oft "ausbleibenden Antworten" oder soll ich besser sagen "Das völlige ignorieren von Fragen "
:D
Sieht man docj das nichts baut. Steht ja nichts im tweet Feed und auxh ein Image ist nicht online. Also baut nicht
..ok THX !..
...dann empfehle ich erstmal als "Übergangslösung" für die User die auch ein Multiboot nutzen möchten das openSpa-Image....und für die,die ohne große "Eigenarbeit" auch das WLAN Nutzen wollen, daß letzte PBNIGMA für die Azbox-Premium+.....
..zumindest die HDMU-14700 (AzboxHD) hätte/könnte man ja zum Down bereitstellen...
... egal...I.Kant hatte schon recht mit seiner Kritik der Urteilskraft insbesondere mit "Kritik der praktischen Vernunft"...
..Sorry wieder mal etwas von "Sat-Thema" abgeschweift... aber muß auch mal sein ^^
Problem. Ist das Images gelöscht werden wenn man die build Umgebung löscht
Problem. Ist das Images gelöscht werden wenn man die build Umgebung löscht
Hi All ...
Here is the latest HDMU image version that works pretty well (dvb-t dongle included) ... but not for USB-storage device auto mount ... probably for not good features flags on kernel config ...
From my upload area [HDMU_14536_AzboxHD_OE_2430_Flash.zip]:
https://mega.nz/#!qA5WmR6Q!0NePhsBBgDj5R5aKd9Nsvapbw9NaKHUE6z-5Ev4f0_o
... many others would like that HDMU Team continue the project also on AZBox !!!
Ciao & Good Weekend ...
bitte neue images testen, mal sehen ob die wieder laufen
http://www.hdmedia-universe.com/board/showthread.php?9852-Hdmu-15079&p=111124#post111124
macmanolo
05.03.2016, 10:52
Hi morly Köntest du das für die folgende azboxhd images ändern?
Wen mann HDMU Images in Multi-Boot von OpenSpa instaliert, diese haben seit lange einen kleinen Fehler.
In der geänderte Datei "bootmisc.sh" gibt es eine "fi" zur viel, genau da wo es beginnt den Ordner für's multiboot zu montieren.
Damit nicht wierd der rest der datei nich ausgeführt, mann must nur der einen "fi" lössen damit alles wieder leuft.
Hier ein keinen teil wo der fehler auftrit
if test ! -L /tmp && test -d /var/tmp
then
rm -rf /tmp
ln -sf /var/tmp /tmp
fi
fi
if [ ! -d "/media/multiboot" ]; then
mkdir /media/multiboot
fi
# aqí se monta la carpeta hdd.
if [ ! -d "/media/hdd" ]; then
mkdir /media/hdd
fi
mfg,
...hatte heute etwas Zeit und hab mal das "überflüssige" fi bei mir händisch raus gelöscht....
... jetzt geht natürlich auch wieder das WebIF ...war ja vorher der Fehler "exceptions.OSError: [Errno 2] No such file or directory: '/media/multiboot' "
THX @macmanolo !
Im nächsten Image gefixed
HELLO
the team stop support azbox??
Tags-Images is empty
No only.have no time AT the.moment
dazulrich
01.09.2016, 21:07
glad to hear you haven't abandoned the Azbox (yet).....
hope you'll find some time soon.
dazulrich
10.09.2016, 10:00
Hallo Bonkel. Danke für die neuen Images.
Gsteamer wird als v1.8.2 angezeigt.
du hattest vor ein paar Wochen angekündigt 1.9.1 einzubauen, Kannst du kurz bestätigen welche gst version drin ist?
1.9.2 ist drin...keine ahnung warum falsch angezeigt wird
man kann ja in den paketen auch die version sehen
opkg list *gstreamer*
dazulrich
10.09.2016, 16:16
Danke. An "opkg list" hatte ich gar nicht gedacht.
Hi,
ich habe da mal ne Frage bezüglich eines Plugins im Mediaportal.
Es gibt da so ein Plugin das nennt sich "Seriesever".
Dieses Plugin funktioniert aber nicht auf diversen Images mit Gstreamer 1.8.1 bzw 1.9.0.
Laut dhwz liegt es am Gstreamer das dieses Plugin nicht funktioniert.
Jetzt sehe ich das ihr im HDMU den Gstreamer 1.9.2 eingebaut habt. Könnt ihr das mal bei euch testen ob mit diesen neuen Gstreamer Seriesever im Mediaportal funktionkert?
Bei Vuplus Receivern und VTI Image mit altem Gstreamer funktionkert dieses HD Serien Plugin.
Ich danke schon mal im voraus
"Könnt ihr das mal bei euch testen ob mit diesen neuen Gstreamer Seriesever im Mediaportal funktionkert?"
.... also ich hab leider derzeit sehr wenig Zeit und die Azbox gar nicht angeschlossen.... aber werden sich sicherlich andere finden,die Deine Bitte aufgreifen....
Es gibt auch ffmpeg. Den man als Player auswählen kann. Serviceapp unter Extensions installieren und auswählen.
Bei mir gestern mit GB Quad Plus ja nicht, @bonkel :confused:.
MfG
Das muss ja auch nicht mit dem ffmpeg (exteplayer3) getestet werden, sondern mit GST und der aktuellen Version.
....und bitte beim Thema bleiben.
Gruß
flac
Und von was hat bonkel geschrieben :rolleyes:?
Unter Serviceapp kann man nur zwischen exteplayer3 und gstplayer auswählen.
Und wie bonkel mir gestern per Skype schrieb ist exteplayer3 ffmpeg.
MfG
@humiboy, wie wäre es denn, wenn Du selber mal testet und die anderen am Ergebnis teilhaben lässt? Oder lässt Du Dir auch sonst immer alles auf dem Silbertablett servieren? So ein Board lebt vom mitmachen.
Laut flac zwar OT:rolleyes:
@humiboy, habe das 15888 Image von gestern auf der Box, aktuelles MP ist auch drauf.
Finde jetzt nicht "Seriesplugin" .
Wenn Du aber "Serienstream" meinst, das geht problemlos.
Getestet mit "Die Rosenheim-Cops".
In Serviceapp ist oben "Orginal" eingestellt, bei exteplayer3 geht's nicht.
Wenn Du was anderes meinst dann bitte genaue Bezeichnung.
MfG
Es geht um "Seriesever" wie ich oben geschrieben habe.
Ich nutze ja eigentlich das openATV Image. Bevor ich selbst das HDMU installiere und selbst teste, dachte ich mir halt ich frage einfach mal hier nach ob es bei denen läuft die das HDMU Image eh schon drauf haben.
Mit Serviceapp und Extplayer3 geht überhaupt nix mit (openATV Image).
Ich hab aber von anderen Usern erfahren das es funktionieren soll mit HDMU und neusten Gstreamer. Wenn ihr das noch bestätigen könnt, brauche ich jetzt nicht extra das HDMU flashen um es heraus zu finden.
Wo finde ich das, unter Grauzone nicht.
MfG
Doch es ist unter Grauzone genau zwischen Serienstream und ShareDir
Weiterhin OT.
Mein Fehler, freilich ist es da, habe irgendwie nach "Serienserver" gesucht ;-)
"Seriesever" funktioniert ebenfalls.
Getestet mit "Dr.House".
MfG
Alles klar vielen Dank Anskar für deine Rückmeldung.
Jetzt weiss ich also das es am Gstreamer doch liegt.
Es hat nicht zufällig noch jemand das HDMU mit alten Gstreamer auf der Box der es auch noch mal kurz gegen testen kann?
...so nun wissen wir das es bei uns funktioniert.
...hier kann wieder über die AzBoxHD diskutiert werden und nicht über irgendwelche Plugins im Mediaportal.
...diese Fragen hätte man im Mediaportal Thread stellen können.
Gruß
flac
Auch wenn es nicht direkt zur Azbox hier gehört.
Das Seriesever in einigen Images nicht funzt liegt nicht beim Mediaportal. Im OpenHDF funzt es nun auch mit GStreamer 1.8.1 nachdem Koivo da was nachgebessert hat.
dazulrich
11.09.2016, 18:52
@Bonkel und Team, welches Azbox dvbmediasink benutzt Ihr? https://github.com/dazulrich/gstreamer1.0-plugin-multibox-dvbmediasink oder nen anderes?
Azbox Me
Image- HDMU_15888_AzboxMe_OE_2651
telnet doesn't work :(((
applet not found
Connection to host lost.
Powered by vBulletin® Version 4.2.5 Copyright ©2024 Adduco Digital e.K. und vBulletin Solutions, Inc. Alle Rechte vorbehalten.