PDA

Archiv verlassen und diese Seite im Standarddesign anzeigen : [AzBoxHD] Image online



bonkel
09.11.2013, 05:52
have fun
5646

morly
09.11.2013, 10:13
kann mir wer die Ausgabe der Zeile posten:

blkid; fdisk -l; mount; cat /proc/cmdline; cat /proc/mtd
Thx ;)

colla
09.11.2013, 11:01
Bootlogo und Spinner laufen schonmal

Das Image hängt leider noch in einer endlos Greenscreen schleife unmittelbar nach dem start (also noch vor der Erstinstallation)
Getestet auf meiner Premium



root@azboxhd:~# blkid; fdisk -l; mount; cat /proc/cmdline; cat /proc/mtd
/dev/mtdblock3: LABEL="YAMON_XRPC" TYPE="romfs"
/dev/hda1: UUID="68eec5e9-c937-4436-8f9a-f0fd7d48d4ee" TYPE="ext3"
/dev/hda3: UUID="829dde79-1957-4092-996a-0e26158c1e93" TYPE="swap"
/dev/hda2: UUID="8c9b5503-ffa5-44c4-addd-c4a656f9a5e8" TYPE="ext2"
/dev/hdb1: UUID="019a4661-ffbd-45b5-8fcb-2fe760aa2432" TYPE="ext2"
/dev/mtdblock/4: LABEL="MIPS_LINUX_XRPC" TYPE="romfs"
/dev/mtdblock/3: LABEL="YAMON_XRPC" TYPE="romfs"
/dev/mtdblock4: LABEL="MIPS_LINUX_XRPC" TYPE="romfs"
-sh: fdisk: not found
rootfs on / type rootfs (rw)
/dev/hda1 on / type ext3 (rw,relatime,errors=continue,barrier=1,data=ordere d)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
tmpfs on /media type tmpfs (rw,relatime,size=64k)
/dev/hdb1 on /media/usb type ext2 (rw,relatime,errors=continue)
tmpfs on /var/volatile type tmpfs (rw,relatime)
usbfs on /proc/bus/usb type usbfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,gid=5,mode=620)
mem=107m console=ttyS0,115200
dev: size erasesize name
mtd0: 00800000 00010000 "CS2: Physically mapped flash"
mtd1: 00020000 00010000 "CS2-Part1"
mtd2: 00020000 00010000 "CS2-Part2"
mtd3: 00040000 00010000 "CS2-Part3"
mtd4: 00680000 00010000 "CS2-Part4"
mtd5: 00100000 00010000 "CS2-Part5"

zeini
09.11.2013, 11:37
Auch meine Premium HD+ startet mit einer Bootschleife.
anstatt fdisk -l habe ich sfdisk -l eingegeben, da auf den Azboxen sfdisk verwendet wird.


root@azboxhd:~# blkid; sfdisk -l; mount; cat /proc/cmdline; cat /proc/mtd
/dev/sda2: UUID="01CD7D362D3CAEB0" TYPE="ntfs"
/dev/hda3: UUID="9b6d341e-c815-488a-8682-8c958f62071b" TYPE="swap"
/dev/sda1: UUID="f32d1af5-2e13-e84f-15c6-da96271691b9" TYPE="ext3"
/dev/hda5: UUID="dd1cf8f2-5913-48fc-8f93-db2b5f860733" TYPE="ext3"
/dev/hda2: UUID="b74cb93f-d4cb-48f3-a735-84af160cefe2" TYPE="ext2"
/dev/mtdblock3: LABEL="YAMON_XRPC" TYPE="romfs"
/dev/mtdblock4: LABEL="MIPS_LINUX_XRPC" TYPE="romfs"
/dev/hda1: UUID="71cd7420-134a-4f27-ac4d-1752ff385b75" TYPE="ext3"
/dev/mtdblock/4: LABEL="MIPS_LINUX_XRPC" TYPE="romfs"
/dev/mtdblock/3: LABEL="YAMON_XRPC" TYPE="romfs"

Disk /dev/hda: 15538 cylinders, 16 heads, 63 sectors/track
Units = cylinders of 516096 bytes, blocks of 1024 bytes, counting from 0

Device Boot Start End #cyls #blocks Id System
/dev/hda1 0+ 371 372- 187487+ 83 Linux
/dev/hda2 372 380 9 4536 83 Linux
/dev/hda3 381 498 118 59472 82 Linux swap / Solaris
/dev/hda4 499 15537 15039 7579656 5 Extended
/dev/hda5 499+ 15537 15039- 7579655+ 83 Linux

Disk /dev/mtdblock0: 1 cylinders, 255 heads, 63 sectors/track

sfdisk: ERROR: sector 2006605284 does not have an msdos signature
sfdisk: /dev/mtdblock0: unrecognized partition table type

sfdisk: No partitions found


Disk /dev/mtdblock1: 0 cylinders, 255 heads, 63 sectors/track

sfdisk: ERROR: sector 2006605284 does not have an msdos signature
sfdisk: /dev/mtdblock1: unrecognized partition table type

sfdisk: No partitions found


Disk /dev/mtdblock2: 0 cylinders, 255 heads, 63 sectors/track

sfdisk: ERROR: sector 2006605284 does not have an msdos signature
sfdisk: /dev/mtdblock2: unrecognized partition table type

sfdisk: No partitions found


Disk /dev/mtdblock3: 0 cylinders, 255 heads, 63 sectors/track

sfdisk: ERROR: sector 2006605284 does not have an msdos signature
sfdisk: /dev/mtdblock3: unrecognized partition table type

sfdisk: No partitions found


Disk /dev/mtdblock4: 0 cylinders, 255 heads, 63 sectors/track

sfdisk: ERROR: sector 2006605284 does not have an msdos signature
sfdisk: /dev/mtdblock4: unrecognized partition table type

sfdisk: No partitions found


Disk /dev/mtdblock5: 0 cylinders, 255 heads, 63 sectors/track

sfdisk: ERROR: sector 2006605284 does not have an msdos signature
sfdisk: /dev/mtdblock5: unrecognized partition table type

sfdisk: No partitions found


Disk /dev/sda: 121601 cylinders, 255 heads, 63 sectors/track
Units = cylinders of 8225280 bytes, blocks of 1024 bytes, counting from 0

Device Boot Start End #cyls #blocks Id System
/dev/sda1 0+ 57859 57860- 464760418+ 83 Linux
/dev/sda2 57860 121600 63741 511999582+ 7 HPFS/NTFS/exFAT
/dev/sda3 0 - 0 0 0 Empty
/dev/sda4 0 - 0 0 0 Empty
rootfs on / type rootfs (rw)
/dev/hda1 on / type ext3 (rw,relatime,errors=continue,barrier=1,data=ordere d)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
tmpfs on /media type tmpfs (rw,relatime,size=64k)
/dev/sda1 on /media/usb type ext3 (rw,relatime,barrier=1,data=ordered)
devpts on /dev/pts type devpts (rw,relatime,gid=5,mode=620)
tmpfs on /var/volatile type tmpfs (rw,relatime)
usbfs on /proc/bus/usb type usbfs (rw,relatime)
/dev/hda5 on /media/DOMExtender type ext3 (rw,relatime,errors=continue,barrier=1,data=ordere d)
/dev/hda5 on /usr type ext3 (rw,relatime,errors=continue,barrier=1,data=ordere d)
mem=107m console=ttyS0,115200
dev: size erasesize name
mtd0: 00800000 00010000 "CS2: Physically mapped flash"
mtd1: 00020000 00010000 "CS2-Part1"
mtd2: 00020000 00010000 "CS2-Part2"
mtd3: 00040000 00010000 "CS2-Part3"
mtd4: 00680000 00010000 "CS2-Part4"
mtd5: 00100000 00010000 "CS2-Part5"

jteetz
09.11.2013, 11:52
Das ging ja schnell mit dem Image.
Aber wenn ich die Kommentare dazu lese ,warte ich lieber noch.
Wie wird denn das Image installiert?

zeini
09.11.2013, 12:05
So wie alle anderen E2-Images. Mittels Azup 2.2.7 von deinem PC aus.

arci
09.11.2013, 12:26
My Friends ... error loop white-crash ... tested on Ultra model:

crashlog


<?xml version="1.0" encoding="utf-8"?>
<HDMU>
<enigma2>
<crashdate>Fri Mar 8 11:20:49 2013</crashdate>
<compiledate>Nov 9 2013</compiledate>
<skin>skin.xml</skin>
<sourcedate>2013-11-09</sourcedate>
<rev>
<![CDATA[
-----====== HDMU 11705 enigma2 Git 796 ======-----
]]>
</rev>
<freespace>
<![CDATA[
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/hda1 181500 142872 29260 83% /
tmpfs 64 0 64 0% /media
tmpfs 51040 248 50792 0% /var/volatile
]]>
</freespace>
<freeram>
<![CDATA[
total used free shared buffers
Mem: 102080 100260 1820 0 7108
-/+ buffers: 93152 8928
Swap: 59388 0 59388
]]>
</freeram>
<version>3.0.0</version>
</enigma2>
<image>
<stbmodel>azboxhd</stbmodel>
<kernelversion>
<![CDATA[
Linux azboxhd 3.9.2-opensat #1 PREEMPT Sat Nov 9 02:51:06 CET 2013 mips GNU/Linux
]]>
</kernelversion>
<kernelcmdline>mem=107m console=ttyS0,115200</kernelcmdline>
<nimsockets>NIM Socket 0:</nimsockets>
<imageversion>
<!-- No such file or directory -->
</imageversion>
<imageissue>
<![CDATA[
mips 3.1 %h

]]>
</imageissue>
</image>
<crashlogs>
<enigma2crashlog>
<![CDATA[
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
+ (9) GFBDC
16352k video mem
- double buffering available!
9152kB available for acceleration surfaces.
resolution: 1280 x 720 x 32 (stride: 5120)
+ (9) gLCDDC
found OLED display!
lcd buffer 0x7e6280 8448 bytes, stride 132
LCD resolution: 132 x 64 x 8 (stride: 132)
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) UHF Modulator
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "dreambox advanced remote control (native)" is a remotecontrol
Found 1 input devices.
+ (22) Hdmi CEC driver
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
done, found 0 common interface slots
+ (35) CA handler
+ (36) Stream server
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryDVD
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
---- opening lame channel db
reading services (version 4)
loaded 6444 services
scanning for frontends..
opening frontend 0
close frontend 0
boxtype detection via /proc/stb/info not possible... use fallback via demux count!

found 1 adapter, 1 frontends(1 sim) and 3 demux, boxtype 1
Use valid Linux Time :) (RTC?)
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
Loading spinners...
[ePNG] couldn't open /usr/share/enigma2/skin_default/spinner/wait13.png
found 12 spinner!

setIoPrio best-effort level 3 ok
main thread is non-idle! display spinner!
Failed to open /dev/dbox/fp0
[Harddisk] enumerating block devices...
new Harddisk hda -> /dev/hda -> /dev/hda
[ePopen] command: ('sdparm', 'sdparm', '--set=SCT=0', '/dev/hda')
unable to load config ([Errno 2] No such file or directory: '/etc/enigma2/settings'), assuming defaults...
Reading satellites.xml
sec config cleared
setSlotInfo for dvb frontend 0 to slotid 0, descr STV090x Multistandard, need rotorworkaround No, enabled Yes, DVB-S2 Yes
slot: 0 configmode: simple
diseqcmode: diseqc_a_b
sec config completed
[InfoBar] Failed to load resumepoints: [Errno 2] No such file or directory: '/home/root/resumepoints.pkl'
loading bouquet... /etc/enigma2/bouquets.tv 1
loading bouquet... /etc/enigma2/userbouquet.mein_tv.tv 1
47 entries in Bouquet userbouquet.mein_tv.tv
loading bouquet... /etc/enigma2/userbouquet.hdtv.tv 48
36 entries in Bouquet userbouquet.hdtv.tv
loading bouquet... /etc/enigma2/userbouquet.sky_hdtv.tv 84
19 entries in Bouquet userbouquet.sky_hdtv.tv
loading bouquet... /etc/enigma2/userbouquet.sky_cinema.tv 103
10 entries in Bouquet userbouquet.sky_cinema.tv
loading bouquet... /etc/enigma2/userbouquet.sky__welt___extra.tv 113
35 entries in Bouquet userbouquet.sky__welt___extra.tv
loading bouquet... /etc/enigma2/userbouquet.sky_bundesliga.tv 148
21 entries in Bouquet userbouquet.sky_bundesliga.tv
loading bouquet... /etc/enigma2/userbouquet.sky_sport.tv 169
38 entries in Bouquet userbouquet.sky_sport.tv
loading bouquet... /etc/enigma2/userbouquet.austriasat.tv 207
13 entries in Bouquet userbouquet.austriasat.tv
loading bouquet... /etc/enigma2/userbouquet.kinder.tv 220
12 entries in Bouquet userbouquet.kinder.tv
loading bouquet... /etc/enigma2/userbouquet.musik.tv 232
16 entries in Bouquet userbouquet.musik.tv
loading bouquet... /etc/enigma2/userbouquet.oesterreich.tv 248
27 entries in Bouquet userbouquet.oesterreich.tv
loading bouquet... /etc/enigma2/userbouquet.italien.tv 275
89 entries in Bouquet userbouquet.italien.tv
loading bouquet... /etc/enigma2/userbouquet.schweiz.tv 364
20 entries in Bouquet userbouquet.schweiz.tv
loading bouquet... /etc/enigma2/userbouquet.holland.tv 384
23 entries in Bouquet userbouquet.holland.tv
loading bouquet... /etc/enigma2/userbouquet.sky_select.tv 407
14 entries in Bouquet userbouquet.sky_select.tv
loading bouquet... /etc/enigma2/userbouquet.xxx.tv 421
47 entries in Bouquet userbouquet.xxx.tv
loading bouquet... /etc/enigma2/userbouquet.favourites.tv 468
0 entries in Bouquet userbouquet.favourites.tv
17 entries in Bouquet bouquets.tv
loading bouquet... /etc/enigma2/bouquets.radio 1
loading bouquet... /etc/enigma2/userbouquet.deutsche.radio 1
19 entries in Bouquet userbouquet.deutsche.radio
loading bouquet... /etc/enigma2/userbouquet.favourites.radio 20
0 entries in Bouquet userbouquet.favourites.radio
2 entries in Bouquet bouquets.radio
[FONT] adding font /usr/share/fonts/nmsbd.ttf...OK (Regular)
[FONT] adding font /usr/share/fonts/andale.ttf...OK (Fixed)
[FONT] adding font /usr/share/fonts/goodtime.ttf...OK (Crs)
[FONT] adding font /usr/share/fonts/age.ttf...OK (Age)
[FONT] adding font /usr/share/fonts/tuxtxt.ttf...OK (Console)
[FONT] adding font /usr/share/fonts/time.ttf...OK (BMCTime)
[FONT] adding font /usr/share/fonts/ae_AlMateen.ttf...OK (Replacement)
[FONT] adding font /usr/share/fonts/md_khmurabi_10.ttf...OK (Regular)
[FONT] adding font /usr/share/fonts/valis_lcd.ttf...OK (Digital)
[FONT] adding font /usr/share/fonts/valis_enigma.ttf...OK (Subs)
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 25] Inappropriate ioctl for device >
Activating keymap: Default (US)
[ePopen] command: loadkmap < /usr/share/keymaps/default.kmap
Activating language English
[ePopen] command: ip -o addr show dev eth0
setLCDBrightness 25
[LCD] can't open /dev/dbox/fp0
setLCDBrightness 127
[LCD] can't open /dev/dbox/fp0
getModeList for port DVI-PC
remove DVI-PC because of not existing modes
getModeList for port YPbPr
getModeList for port Scart
getModeList for port DVI
hotplug on dvi
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
setMode - port: YPbPr mode: 720p rate: 50Hz
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
[NetworkBrowser] fallback to default translation for NetworkBrowser
[NetworkBrowser] fallback to default translation for Search for network shares
[NetworkBrowser] fallback to default translation for MountManager
[NetworkBrowser] fallback to default translation for Manage network shares
[NetworkBrowser] fallback to default translation for Mount again
[NetworkBrowser] fallback to default translation for Attempt to mount shares again
[WebInterface] set language to en
[WebInterface] set language to en
[WebInterface] fallback to default translation for Webinterface
[WebInterface] fallback to default translation for Configuration for the Webinterface
Media Center: Import evfd failed
loadSkin: Screen already defined elsewhere: HDMU_MainMenu
loadSkin: Screen already defined elsewhere: HDMU_SoftcamControl
loadSkin: Screen already defined elsewhere: HDMU_OverclockControl
loadSkin: Screen already defined elsewhere: HDMU_SystemControl
loadSkin: Screen already defined elsewhere: HDMU_TunerControl
loadSkin: Screen already defined elsewhere: HDMU_SystemInfos
loadSkin: Screen already defined elsewhere: HDMU_ufsup
loadSkin: Screen already defined elsewhere: HDMU_OSDControl
loadSkin: Screen already defined elsewhere: HDMU_VFDControl
loadSkin: Screen already defined elsewhere: HDMU_VideoControl
loadSkin: Screen already defined elsewhere: HDMU_DLNAServer
loadSkin: Screen already defined elsewhere: HDMU_OpenVPN
loadSkin: Screen already defined elsewhere: HDMU_SkinControl
HDMU Center: Import evfd failed
starting hotplug handler
wasTimerWakeup failed!
[SKIN] No skin to read...
[Toplevel.importExternalModules] Imported external module: Example
[HTTPRootResource}.__init__
[Webinterface] started on 0.0.0.0:80 auth=False ssl=False
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[HTTPRootResource}.__init__
[Webinterface] started on 0.0.0.0:443 auth=True ssl=True
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[EPGC] setCacheFile read/write epg data from/to '/hdd/epg.dat'
[EPGC] time updated.. start EPG Mainloop
[EPGC] /hdd/epg.dat not found, try /epg.dat
Reading ['/usr/lib/enigma2/python/Plugins/SystemPlugins/Videomode/videowizard.xml']
getStepWithID: start
result: nothing
('en_EN', ('English', 'en', 'EN'))
Screen <function VideoWizard at 0x13c1570>((), {}): <type 'exceptions.IOError'>
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 225, in create
return screen(self, *arguments, **kwargs)
File "/usr/lib/enigma2/python/Plugins/SystemPlugins/Videomode/plugin.py", line 230, in VideoWizard
File "/usr/lib/enigma2/python/Plugins/SystemPlugins/Videomode/VideoWizard.py", line 54, in __init__
File "/usr/lib/enigma2/python/Screens/Rc.py", line 26, in __init__
File "/usr/lib/enigma2/python/Screens/Rc.py", line 41, in readPositions
File "/usr/lib/python2.7/xml/etree/ElementTree.py", line 611, in __init__
File "/usr/lib/python2.7/xml/etree/ElementTree.py", line 646, in parse
IOError: [Errno 2] No such file or directory: '/usr/share/enigma2/rc_models/xpeedlx/rcpositions.xml'
open /dev/dbox/fp0 for wakeup timer clear failed!(No such file or directory)
EXCEPTION IN PYTHON STARTUP CODE:
------------------------------------------------------------
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 593, in <module>
runScreenTest()
File "/usr/lib/enigma2/python/mytest.py", line 477, in runScreenTest
runNextScreen(session, screensToRun)
File "/usr/lib/enigma2/python/mytest.py", line 471, in runNextScreen
session.openWithCallback(boundFunction(runNextScre en, session, screensToRun[1:]), screen, *args)
File "/usr/lib/enigma2/python/mytest.py", line 293, in openWithCallback
dlg = self.open(screen, *arguments, **kwargs)
File "/usr/lib/enigma2/python/mytest.py", line 304, in open
dlg.isTmp = True
AttributeError: 'NoneType' object has no attribute 'isTmp'
open /dev/dbox/fp0 for wakeup timer clear failed!(No such file or directory)
------------------------------------------------------------
(exit code 5)
getResolvedKey config.plugins.crashlogautosubmit.sendAnonCrashlog failed !! (Typo??)
getResolvedKey config.plugins.crashlogautosubmit.addNetwork failed !! (Typo??)
getResolvedKey config.plugins.crashlogautosubmit.addWlan failed !! (Typo??)
]]>
</enigma2crashlog>
</crashlogs>
</HDMU>


Ciao ... :)

morly
09.11.2013, 12:39
Thx - kann man das Image auch via Stick flashen?

TheChip
09.11.2013, 12:50
Nein Morly, geht nur via PC Tool.

morly
09.11.2013, 13:01
thanks - hab mich gerade eingelesen :)

arci
09.11.2013, 13:16
@Morly ...

For first time run ... resolve the wrong assign rcpositions xml path ... with this ... /usr/share/enigma2/rc_models/azboxhd/rcpositions.xml

Now ... the wizard is OK and run ! :)

56475648

Ciao ...

bonkel
09.11.2013, 14:51
war dann doch schon zu spät , das Image davor ging noch lol

neues baut grad

arci
09.11.2013, 15:59
@bonkel

Sorry ... but with new version HDMU_11706_AzboxHD_OE_796_Flash ... not resolve !

... new issue come on Enigma2 python side:



root@azboxhd:~# enigma2.sh
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
+ (9) GFBDC
16352k video mem
- double buffering available!
9152kB available for acceleration surfaces.
resolution: 1280 x 720 x 32 (stride: 5120)
+ (9) gLCDDC
found OLED display!
lcd buffer 0x7e65c0 8448 bytes, stride 132
LCD resolution: 132 x 64 x 8 (stride: 132)
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) UHF Modulator
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "dreambox advanced remote control (native)" is a remotecontrol
Found 1 input devices.
+ (22) Hdmi CEC driver
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
done, found 0 common interface slots
+ (35) CA handler
+ (36) Stream server
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryDVD
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
---- opening lame channel db
reading services (version 4)
loaded 6444 services
scanning for frontends..
opening frontend 0
close frontend 0
boxtype detection via /proc/stb/info not possible... use fallback via demux coun t!

found 1 adapter, 1 frontends(1 sim) and 3 demux, boxtype 1
Use valid Linux Time :) (RTC?)
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
Loading spinners...
[ePNG] couldn't open /usr/share/enigma2/skin_default/spinner/wait13.png
found 12 spinner!

executing main
setIoPrio best-effort level 3 ok
main thread is non-idle! display spinner!
Failed to open /dev/dbox/fp0
[Harddisk] enumerating block devices...
new Harddisk hda -> /dev/hda -> /dev/hda
[ePopen] command: ('sdparm', 'sdparm', '--set=SCT=0', '/dev/hda')
unable to load config ([Errno 2] No such file or directory: '/etc/enigma2/settin gs'), assuming defaults...
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 18, in <module>
from Screens import InfoBar
File "/usr/lib/enigma2/python/Screens/InfoBar.py", line 5, in <module>
File "/usr/lib/enigma2/python/Screens/MovieSelection.py", line 1, in <module>
File "/usr/lib/enigma2/python/Screens/Screen.py", line 4, in <module>
File "/usr/lib/enigma2/python/Components/GUISkin.py", line 1, in <module>
File "/usr/lib/enigma2/python/Components/GUIComponent.py", line 1, in <module>
File "/usr/lib/enigma2/python/skin.py", line 15, in <module>
File "/usr/lib/enigma2/python/Components/RcModel.py", line 81, in <module>
File "/usr/lib/enigma2/python/Components/RcModel.py", line 15, in __init__
File "/usr/lib/enigma2/python/Components/RcModel.py", line 32, in readRcTypeFr omProc
AttributeError: RcModel instance has no attribute 'RCTYPE_AZBOXHD'
---- saving lame channel db
saved 236 channels and 6444 services!
release cached channel (timer timeout)
set RTC to previous valid time
- (41) eServiceFactoryDVD
- (41) eServiceFactoryM2TS
- (41) eServiceFactoryMP3
- (41) eServiceFactoryFS
- (41) eServiceFactoryDVB
- (40) eServiceCenter
clear instance
- (36) Stream server
- (35) CI Slots
- (35) CA handler
- (30) eActionMap
- (22) Hdmi CEC driver
- (21) input device driver
- (20) DVB-CI UI
- (20) UHF Modulator
- (20) RC Input layer
- (20) misc options
- (20) AVSwitch Driver
- (15) eWindowStyleManager
- (10) gRC
waiting for gRC thread shutdown
gRC thread has finished
- (9) GFBDC
- (9) gLCDDC
- (9) Font Render Class
- (8) graphics acceleration manager
- (5) Tuxtxt
- (1) Background File Eraser
reached rl -1
root@azboxhd:~#


Ciao ...

bonkel
09.11.2013, 16:46
thx gefixt.kommt

arci
09.11.2013, 17:37
@bonkel

Thanks for new 11707 ... but You are came back to first issue 11705 version :)

5651

The save path in your compile source system "by default" for files "rc.png" & "rcpositions.xml" is /usr/share/enigma2/rc_models/xpeedlx/ ... but of course this folder does not exist in the AZBox compiled system.

You must change in /usr/share/enigma2/rc_models/azboxhd/ ... and after all is OK ... with inizialize wizard setup !

I hope now it is clearer ... :)

Ciao ...

bonkel
09.11.2013, 17:39
how fast are you ? lol
2 minutes after upload, i delete this Image, because of missing fix :D

there is a new on the way ^^

zeini
09.11.2013, 17:39
Das gleiche Fehlerbild habe ich auf meiner Premium HD+ mit 11707

Edit: Aha Bonkel hat es schon gesehen.

arci
09.11.2013, 17:45
how fast are you ? lol
2 minutes after upload, i delete this Image, because of missing fix :D

there is a new on the way ^^

Ok ... i re-check :) Thanks

zeini
09.11.2013, 17:52
Mit 11708 auch die gleiche Fehlermeldung wie das Bild von Beitrag 15.

arci
09.11.2013, 18:11
For me the 11708 version ... now is OK

P.S. But you chose the easy general way for rc_models ! :)

5652

Only one thing ... if you can make a little change on delay time for RCU control (interval between keys when repeating) ... by default 100 ms is too short ... better 300 ms ... for correct response in OSD menu system !

... we can go further with other tests! :)

Thank a lot ... @bonkel

bonkel
09.11.2013, 18:32
zeini kannst nochmal neu laden, oder vielleicht falsche Datei geflashed?

ich seh jetzt kein fehler mehr

bonkel
09.11.2013, 18:37
was ich noch fragen wollt, wenn ihr euren tv ohne overscan benutzt, ist bei euch das osd also die gui auch zu klein?
besonders gut im mediaportal zu sehen
das sind eigentlich alles Skins, die das ganze bild ausfüllen , so zumindest bei sh4,arm und anderen mips

denke das liegt an den treibern, wäre schön wenn das jemand the-ripper weiterleiten könnte

zeini
09.11.2013, 18:53
Ich habe bei mir den Pfad /usr/share/enigma2/rc_models/azboxhd auf /usr/share/enigma2/rc_models/xpeedlx geändert.
Nun funzt es bei mir.

Ich kann aber keine Aufnahmen abspielen. Weder von anderen Images, noch jene, die mit diesem Image aufgenommen wurden. Weder im Mediaplayer noch im Mediacenter. Wenn ich das Mediacenter verlassen will, habe ich Dauerspin, oder heißt es hier HDMU-Wackler. ;)

Ansonsten schaut es mal ganz gut aus.

bonkel
09.11.2013, 18:56
aufnahmen hab ich nich getestet...(war da nich was mit kernel3.9.2?)

das mit mediacenter spinner beim verlassen hab ich auch :( (seh im log aber nich wo was stört)
Webradio geht aber....mediaportal streams gehen auch

arci
09.11.2013, 19:00
This is my set default 1080i 50 ... with ASUS 23 LCD Full HD HDMI ... I do not think there are problems with the OSD skin!

5653

- A / V streams run with mediaportal
- HDMU Mediacenter ... same problem of zeini
- Network HDD CIFS mount not work with Network Browser ( I must test some TS record on AZBox Premium HDD)

bonkel
09.11.2013, 19:01
yes in screenshots ist ok..but on tv, there is a black border

ravemaster
09.11.2013, 19:03
Was denkst du, soll an den Treibern geändert werden, damit das funktioniert? Das Problem mit zu kleinen Skins hatten wir glaub ich noch nicht.
Ich habs leider selber noch nicht testen können.

bonkel
09.11.2013, 19:11
gute frage
da das tv bild passt, kanns ja nur irgendwas sein, was im bcm teil drin ist Linux/fb.cpp(.h)

bei manchen boxen kann man auch per Telnet im proc eintrag die gui vergrössern und verkleinern, vielleicht ist da auch schon was verkleinert, als vorsorge für overscan

zeini
09.11.2013, 19:19
Das Bild schaut auf meinem TV eigentlich normal aus. Ist eigentlich bei allen Receivern ähnlich.
Ich hänge mal ein F5654oto vom Mediaportal hier an.

Im Radiomodus habe ich keinen Ton.

Die Guidetaste ist eigentlich auch ungewohnt für den Aufruf des Mediaplayers. Hier wäre mE der grafische EPG besser aufgehoben.

bonkel
09.11.2013, 19:23
overscan aktiv?
ich mach mal nen Foto gleoch


noch besser sieht mans wenn man media Center öffnet
dann is im Hintergrund tv bild noch zu sehen

bonkel
09.11.2013, 19:38
hier mal das bild

arci
09.11.2013, 19:41
yes in screenshots ist ok..but on tv, there is a black border

@bonkel ... but I don't see any Black border on screen !?!

56585659

What have you changed in 11709?

bonkel
09.11.2013, 19:49
http://www.hdmedia-universe.com/board/pages.php?pageid=4&log=MIPSenigma2

zeini
09.11.2013, 19:52
Ja, Bonkel, das habe ich auch, wenn ich am TV es so einstelle. Aber beim normalen Bild - ohne OSD - sehe ich trotzdem alles bis zum Rand. Also ist das für mich so in Ordnung.

Beim Radioton, der nicht funzt meinte ich nicht das Webradio. Ich meinte die Radiosender am Sat. Bei diesen habe ich keinen Ton.

ravemaster
09.11.2013, 19:56
Zum Problem mit den Balken um die GUI herum. Das Problem hier ist, dass die SIGMA OSD Skalierung nicht besonders gut funktioniert. Darum sind bei manchen TV's Balken (TV-Bild) um die GUI herum. Bei einigen mehr, bei anderen weniger.

Die gewünschten Dateien hab ich gerade bekommen und hier angehängt.

5660
5661

bonkel
09.11.2013, 20:23
perfekt
hab mal die sleeps geändert, das hab ich schon bei ufs912 und spark so gemacht, ergebniss war ein schnelleres zappen, kannst mal fragen ob er mir daraus mal fertige module bauen kann

ravemaster
09.11.2013, 21:46
Ich werd das gleich mal weiterleiten.

- - - Aktualisiert - - -

So das Modul ist fertig und angehängt. :36_2_35:

5664

bonkel
09.11.2013, 22:04
interessantes ergebniss....wenn man ext4 im kernel aktiviert, startet die box nimmer und bleibt im boot hängen :D

ravemaster
09.11.2013, 22:10
Für ext4 sind glaub ich mehr Anpassungen notwendig. Da hat Fabry im Board von openRSI mehr Erfahrung. Er hat einen angepassten Kernel veröffentlicht, der ext4 aktiviert hat.
ext2 und ext3 sind deaktiviert. Die werden von ext4 verwaltet.

bonkel
09.11.2013, 22:15
ich darf jetzt erstmal recovern :36_2_35::36_2_24:

ravemaster
09.11.2013, 22:20
Ja, so sind unsere AzenZicken. Einmal eine Kleinigkeit anders und schon liebt sie dich nicht mehr. :)

zeini
09.11.2013, 23:07
Ich habe mal die stv090x.co ausgetauscht, mit der hier im Beitrag 37 von Ravemaster angehängten getauscht, der ja von Bonkel beschleunit wurde. Mir kommt vor, dass die Box auch mit diesem Treiber ähnlich schnell umschaltet wie vorher. Ist aber immer schwer zu sagen, wenn man keinen direkten Vergleich nebeneinander hat.

Leopold75
12.11.2013, 00:04
Hallo!
Image für AzBox Elite - er hat diesen Fehler an sich


00:01:31.960 R2[emucworks]: ECM queue size = 32
*** glibc detected *** ./wicardd-mipsel: double free or corruption (top): 0x004c0420 ***
Aborted

Was soll damit werden?
Vielen Dank!

chewie
12.11.2013, 16:31
Hello Gentleman
I am new to this forum, I am glad I join it and ready to learn from you guys.
I have a Azbox P+ I installed the new image and it looks very nice, I am kind of limited regarding the satellites choices, I live in the WEST, I would like to ask if western satellite could be added to the list, KU AND C-BAND.
My performance of satellites would be form 58W TO 129W KU BAND AND C-BAND.
I have a satellite list and in the past I been able to added to the image. I try to access the files with DCC an MAX tools, but it does not let me, I think Telnet does not connect.
If there is another program I can use to add my satellite list, please provide me with this information.
And one last request, maybe is to much to ask, but, here in the WEST we do a lot of Blind Scanning, I noticed that Blind Scan is not a option under the service Menu, is this option going to be added later?
Best regards.
let's have some fun.
Chewie

bonkel
12.11.2013, 17:00
did you enter he right Password?

chewie
12.11.2013, 18:03
Hello Bonkel
Thanks for your quick response, if you are referring to the MAZ program it was set to ID - AZBOX AND PW -ROOT, I never had to set the password on the RCC program, what should it be? is it the same as the MAZ program?
please let me know.
Regards.
Chewie

bonkel
12.11.2013, 18:04
user: root
pass: HDMU

chewie
12.11.2013, 18:34
Thanks bonkel, I will try it out when I get home.
Another question, the Fan on the receiver stays on when the receiver is set to Standby, I was looking for the option to have the fan turn off while on the Standby, is there such an option on this image, I was not able to locate this option.
Please let me know.
Thanks in advance.
Regards
Chewie

bonkel
12.11.2013, 18:39
it's a Alpha Image, there is no Option for that at the Moment, have other Problems with this box ^^

arci
12.11.2013, 20:49
I hope you receive all the necessary support from Sasha ... because your distrubution has all the elements to be an excellent Enigma 2 distribution for old AZBox!

Congratulations @ bonkel and friends :)

faus
12.11.2013, 23:58
gracias por la imagen

chewie
13.11.2013, 04:50
Hello Bonkel
I was able to load my Sat list to this firm and it works very good so far, WiFi works good. I thank you for your help and thanks for this image.
Regards.
Chewie

papaluna
16.11.2013, 10:34
Because to install this image on usb, simpre which was started Dom, questions can only be installed in Dom and there is no possibility in usb. thanks

macmanolo
16.11.2013, 21:52
So. heute morgen habe ich meine AZBoxHD Premium repariert (hatte eine durchgebrannte Transistor in SMD-Format, in zur ersetzte war eine Zircus Arbeit), dan habe ich sofort der Firmware von HDMU geflash und hat alles funktioniert außer dem Tuner DVB-T, er wird ezwar erkant kan aber keine kanäle sehen auch nicht nach eine neue Suche, (0 kanäle gefunden), in sat alles ok.

Als Alpha-Version ist garnicht schlecht, ich freue mich son auf die folgenden Entwicklungen im diesen image.

Danke am alle betiligte für die gute arbeit.

mfg.

Lucjan
17.11.2013, 15:33
Hallo Bonkel, ist die Azbox wieder ok?
Ich würde mich sehr freuen über neue Image.

bonkel
19.11.2013, 23:23
nein, treiber mag noch nicht

ravemaster
23.11.2013, 12:17
Hallo bonkel.

Wie siehts aus mit deiner Box? Können wir dir irgendwie behilflich sein?

bonkel
23.11.2013, 18:35
ich arbeite mit win8..hab den treiber mittlerweile zum laufen kekommen....
bekomme aber keine ausgabe im putty



wenn ich die box an mach kommt, power on , booting und das wars
wie gesagt keine ausage im putty....
wenn du ne Idee hast wäre gut ^^

bonkel
23.11.2013, 19:11
hat sich erledigt, hab jetzt ne ausgabe


irgendwie is tx und rx vertauscht , hab jetzt 4 mal geprüft und dachte schon bin bescheuert

arci
23.11.2013, 19:38
When you do more things ... can happen :)

Are you able to go ahead with implementations?

Thanks for your time ...

Ciao

ravemaster
23.11.2013, 19:53
Das war bei mir gleich. War auch vertauscht. Ich hoffe du kriegst das Teil jetzt wieder zum Laufen. Ich hatte auch noch Probs mit dem TFTP-Server vom Paket. Hab mir dann die 64 Bit Version geladen. Mit dem gings.

bonkel
24.11.2013, 17:17
online

bonkel
24.11.2013, 17:28
wichtig ist neu zu flashen...online update könnte in die hose gehen

zeini
24.11.2013, 19:33
Super, dass sich da wieder was tut!
Neu geflasht mit HDMU_11850_AzboxHD_OE_834_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11850_AzboxHD_OE_834_Flash.zip).

Aufnahmen lassen sich aber leider immer noch nicht abspielen. edit: Funzt nach reboot

Im Radiomodus (Satradio nicht Webradio) werden die Kanäle etwa 1 Sekunde angespielt und dann ist der Ton weg.
Will man dann vom Radiomodus in den TV-Modus wechseln mit der TV/Radiotaste so funzt das nicht.

Das wären mal die wichtigsten Bugs, die gefixt werden sollten.

bonkel
24.11.2013, 19:35
ich habe aufnahmen extra getestet

deswegen wollte ich ja ext4 haben.....
bei mir klappts....auch timeshift geht

zeini
24.11.2013, 20:25
Danke, stimmt!
Nach neuerlichem reboot funzt jetzt auch bei mir das Abspielen von Aufnahmen. Auch Timeshift.

arci
24.11.2013, 23:48
As I asked for previous versions ... even if you add the cifs module and its management ... I could try recording on HDD ... installed on another az receiver !

Thank you

Ciao ...

arci
27.11.2013, 17:55
I saw that you compiled a new version 11853 [oe 837]!

What's new changelog ?

On the previous version (oe 835) I've noticed that you've enabled the cifs ... but I always had problems with its mount!

Thanks ...

Ciao

arci
27.11.2013, 19:18
I have installed now ... the new version 11853 [oe 837] ... but there is a problem at first boot (before started setup Wizard):

Enigma 2 white crashlog


<?xml version="1.0" encoding="utf-8"?>
<HDMU>
<enigma2>
<crashdate>Fri Mar 8 11:21:53 2013</crashdate>
<compiledate>Nov 24 2013</compiledate>
<skin>skin.xml</skin>
<sourcedate>2013-11-24</sourcedate>
<rev>
<=!=[=C=D=A=T=A=[
-----====== HDMU 11853 enigma2 Git 835 ======-----
]=]=>
</rev>
<freespace>
<=!=[=C=D=A=T=A=[
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/hda1 181500 142880 29252 83% /
tmpfs 64 0 64 0% /media
tmpfs 50980 248 50732 0% /var/volatile
/dev/sda1 3910152 1273040 2637112 33% /media/usb
]=]=>
</freespace>
<freeram>
<=!=[=C=D=A=T=A=[
total used free shared buffers
Mem: 101964 100248 1716 0 11696
-/+ buffers: 88552 13412
Swap: 59388 4 59384
]=]=>
</freeram>
<version>3.0.0</version>
</enigma2>
<image>
<stbmodel>azboxhd</stbmodel>
<kernelversion>
<=!=[=C=D=A=T=A=[
Linux azboxhd 3.9.2-opensat #1 PREEMPT Sun Nov 24 14:28:48 CET 2013 mips GNU/Linux
]=]=>
</kernelversion>
<kernelcmdline>mem=107m console=ttyS0,115200</kernelcmdline>
<nimsockets>NIM Socket 0:</nimsockets>
<imageversion>
<!-- No such file or directory -->
</imageversion>
<imageissue>
<=!=[=C=D=A=T=A=[
mips 3.1 %h

]=]=>
</imageissue>
</image>
<crashlogs>
<enigma2crashlog>
<=!=[=C=D=A=T=A=[
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
+ (9) GFBDC
16352k video mem
- double buffering available!
9152kB available for acceleration surfaces.
resolution: 1280 x 720 x 32 (stride: 5120)
+ (9) gLCDDC
found OLED display!
lcd buffer 0x7ea738 8448 bytes, stride 132
LCD resolution: 132 x 64 x 8 (stride: 132)
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) UHF Modulator
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "dreambox advanced remote control (native)" is a remotecontrol
Found 1 input devices.
+ (22) Hdmi CEC driver
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
done, found 0 common interface slots
+ (35) CA handler
+ (36) Stream server
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryDVD
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
---- opening lame channel db
reading services (version 4)
loaded 236 channels/transponders and 6444 services
scanning for frontends..
opening frontend 0
close frontend 0
boxtype detection via /proc/stb/info not possible... use fallback via demux count!

found 1 adapter, 1 frontends(1 sim) and 3 demux, boxtype 1
Use valid Linux Time :) (RTC?)
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
Loading spinners...
[ePNG] couldn't open /usr/share/enigma2/skin_default/spinner/wait13.png
found 12 spinner!

setIoPrio best-effort level 3 ok
main thread is non-idle! display spinner!
Failed to open /dev/dbox/fp0
[Harddisk] enumerating block devices...
new Harddisk hda -> /dev/hda -> /dev/hda
[ePopen] command: ('sdparm', 'sdparm', '--set=SCT=0', '/dev/hda')
new Harddisk sda -> /dev/sda -> /dev/sda
unable to load config ([Errno 2] No such file or directory: '/etc/enigma2/settings'), assuming defaults...
Reading satellites.xml
sec config cleared
setSlotInfo for dvb frontend 0 to slotid 0, descr STV090x Multistandard, need rotorworkaround No, enabled Yes, DVB-S2 Yes
slot: 0 configmode: simple
diseqcmode: diseqc_a_b
sec config completed
[InfoBar] Failed to load resumepoints: [Errno 2] No such file or directory: '/home/root/resumepoints.pkl'
[FONT] adding font /usr/share/fonts/nmsbd.ttf...OK (Regular)
[FONT] adding font /usr/share/fonts/andale.ttf...OK (Fixed)
[FONT] adding font /usr/share/fonts/goodtime.ttf...OK (Crs)
[FONT] adding font /usr/share/fonts/age.ttf...OK (Age)
[FONT] adding font /usr/share/fonts/tuxtxt.ttf...OK (Console)
[FONT] adding font /usr/share/fonts/time.ttf...OK (BMCTime)
[FONT] adding font /usr/share/fonts/ae_AlMateen.ttf...OK (Replacement)
[FONT] adding font /usr/share/fonts/md_khmurabi_10.ttf...OK (Regular)
[FONT] adding font /usr/share/fonts/valis_lcd.ttf...OK (Digital)
[FONT] adding font /usr/share/fonts/valis_enigma.ttf...OK (Subs)
[FONT] adding font /usr/share/fonts/nmsbd.ttf...OK (FdLcD)
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 25] Inappropriate ioctl for device >
[iInputDevices] setRepeat for device event0 to 150 ms
[iInputDevices] setDelay for device event0 to 700 ms
Activating keymap: Default (US)
[ePopen] command: loadkmap < /usr/share/keymaps/default.kmap
Activating language English
[ePopen] command: ip -o addr show dev eth0
setLCDBrightness 25
[LCD] can't open /dev/dbox/fp0
setLCDBrightness 127
[LCD] can't open /dev/dbox/fp0
[NetworkBrowser] fallback to default translation for NetworkBrowser
[NetworkBrowser] fallback to default translation for Search for network shares
[NetworkBrowser] fallback to default translation for MountManager
[NetworkBrowser] fallback to default translation for Manage network shares
[NetworkBrowser] fallback to default translation for Mount again
[NetworkBrowser] fallback to default translation for Attempt to mount shares again
getModeList for port DVI-PC
remove DVI-PC because of not existing modes
getModeList for port YPbPr
getModeList for port Scart
getModeList for port DVI
hotplug on dvi
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
setMode - port: YPbPr mode: 720p rate: 50Hz
-> setting aspect, policy, policy2, wss 16:9 panscan letterbox auto
Media Center: Import evfd failed
HDMU Center: Import evfd failed
[WebInterface] set language to en
[WebInterface] set language to en
[WebInterface] fallback to default translation for Webinterface
[WebInterface] fallback to default translation for Configuration for the Webinterface
starting hotplug handler
wasTimerWakeup failed!
setLCDBrightness 127
[LCD] can't open /dev/dbox/fp0
[NAVIGATION] USE DEEPSTAND-WORKAROUND FOR THIS BOXTYPE (azboxhd) !!
[SKIN] No skin to read...
[Toplevel.importExternalModules] Imported external module: Example
[HTTPRootResource}.__init__
[Webinterface] started on 0.0.0.0:80 auth=False ssl=False
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[HTTPRootResource}.__init__
[Webinterface] started on 0.0.0.0:443 auth=True ssl=True
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[EPGC] setCacheFile read/write epg data from/to '/hdd/epg.dat'
[EPGC] time updated.. start EPG Mainloop
[EPGC] /hdd/epg.dat not found, try /epg.dat
Reading ['/usr/lib/enigma2/python/Plugins/SystemPlugins/Videomode/videowizard.xml']
getStepWithID: start
result: nothing
('en_EN', ('English', 'en', 'EN'))
Screen <function VideoWizard at 0x149a7f0>((), {}): <type 'exceptions.IOError'>
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 227, in create
return screen(self, *arguments, **kwargs)
File "/usr/lib/enigma2/python/Plugins/SystemPlugins/Videomode/plugin.py", line 230, in VideoWizard
File "/usr/lib/enigma2/python/Plugins/SystemPlugins/Videomode/VideoWizard.py", line 54, in __init__
File "/usr/lib/enigma2/python/Screens/Rc.py", line 26, in __init__
File "/usr/lib/enigma2/python/Screens/Rc.py", line 41, in readPositions
File "/usr/lib/python2.7/xml/etree/ElementTree.py", line 611, in __init__
File "/usr/lib/python2.7/xml/etree/ElementTree.py", line 646, in parse
IOError: [Errno 2] No such file or directory: '/usr/share/enigma2/rc_models/vu/rcpositions.xml'
open /dev/dbox/fp0 for wakeup timer clear failed!(No such file or directory)
EXCEPTION IN PYTHON STARTUP CODE:
------------------------------------------------------------
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 648, in <module>
runScreenTest()
File "/usr/lib/enigma2/python/mytest.py", line 498, in runScreenTest
runNextScreen(session, screensToRun)
File "/usr/lib/enigma2/python/mytest.py", line 492, in runNextScreen
session.openWithCallback(boundFunction(runNextScre en, session, screensToRun[1:]), screen, *args)
File "/usr/lib/enigma2/python/mytest.py", line 295, in openWithCallback
dlg = self.open(screen, *arguments, **kwargs)
File "/usr/lib/enigma2/python/mytest.py", line 306, in open
dlg.isTmp = True
AttributeError: 'NoneType' object has no attribute 'isTmp'
open /dev/dbox/fp0 for wakeup timer clear failed!(No such file or directory)
------------------------------------------------------------
(exit code 5)
getResolvedKey config.plugins.crashlogautosubmit.sendAnonCrashlog failed !! (Typo??)
getResolvedKey config.plugins.crashlogautosubmit.addNetwork failed !! (Typo??)
getResolvedKey config.plugins.crashlogautosubmit.addWlan failed !! (Typo??)
]=]=>
</enigma2crashlog>
</crashlogs>
</HDMU>



please change path for "rcpositions.xml" file ... here there is a vu path (/usr/share/enigma2/rc_models/vu/) !

Another things : If you add the RtiSYS plugin system ... at least ... who has the AZPremium Plus can turn off the fan ... in standby !

Thanks ...

Ciao ...

bonkel
27.11.2013, 20:59
fixed...

arci
27.11.2013, 22:44
Thanks @bonkel ... now the HDMU is ready to start ! :)

When you find the time to dedicate!


For you information ... your add RtiSYS system plugin is not good ... the plugin is not loaded !

Check the correct refer code of this python plugin ... inside python files there is your linux path /home/user ... instead of registration path on enigma2 plugin environment !

5784 5785 5786

Thanks ...

Ciao

bonkel
27.11.2013, 23:14
Check the correct refer code of this python plugin ... inside python files there is your linux path /home/user ... instead of registration path on enigma2 plugin environment !

Thanks ...

Ciao

thats no Problem, ist ok


can you attach the rtisys plugin ?

arci
27.11.2013, 23:58
thats no Problem, ist ok


can you attach the rtisys plugin ?

I have this version with the latest fix ntpdate update time ... 5790



https://github.com/OpenAZBox/RTi-SYS


Edit ... or there are custom versions of OpenRSi @Sattommy, OpenSPA, OpenATV @Captain or @Persian for oe-core ! You can ask them!

Ciao ...

zeini
30.11.2013, 16:56
Im Radiomodus (Satradio nicht Webradio) werden die Kanäle etwa 1 Sekunde angespielt und dann ist der Ton weg.
Will man vom Radiomodus in den TV-Modus wechseln mit der TV/Radiotaste so funzt das nicht.

Während einer Aufnahme sollte die rote LED an der Box leuchten.

litas
01.12.2013, 19:25
Hallo und danke mal für dieses Image, läuft super !!!

Wäre es möglich für die AzBox und diesem Image ein NFS-Utils zu bauen?

Ich benötige noch den NFS-Server für meine AzBox.

Danke schon einmal vorab ...

bonkel
01.12.2013, 19:33
opkg list *nfs* mal gemacht?

zeini
07.12.2013, 11:39
Image 11880:
Das Umschalten von TV auf Radio funzt nicht. Drückt man die TV/RADIO Taste tut sich nichts.

Lucjan
10.12.2013, 08:44
Image 11887:
Radiosender & TV/RADIO Taste geht nicht!

bonkel,geht das auf deiner Azbox?

arci
10.12.2013, 20:56
@bonkel

Always ... when you have time !?! :rolleyes:

You must to control ... because the CIFS mount not goes fine (not green icon on net mount device) !

5919

With my others receivers with E2 OpenPLi (Alien 2+ & Mediabox HD LX-1) ... I don't have this problem !

Thanks & Ciao ...

kub110
11.12.2013, 08:44
So wie alle anderen E2-Images. Mittels Azup 2.2.7 von deinem PC aus.

Azup
Azup 2.2.7

arci
16.12.2013, 19:04
@bonkel

HDMU 11904 oe 801 ... bugs:

-aio grab ... does not work ... (unknow stb type)
-HDMU info system ... does not work ... (E2 idle-spinner loop)

Ciao ...

bonkel
16.12.2013, 19:49
@bonkel

HDMU 11904 oe 801 ... bugs:


-HDMU info system ... does not work ... (E2 idle-spinner loop)

Ciao ...

log?.....

bonkel
16.12.2013, 21:27
aio-grab fixed

arci
16.12.2013, 23:33
aio-grab fixed

OK ... Thanks ;)

This is the UART log complete (AZBox Ultra): 5962

& when open the HDMU Center "Info System":



[Skin] Attribute not implemented: scrollbarMode value: showOnDemand
warning, skin is missing element label in <class 'Plugins.Extensions.HDMUCenter.HDMU_SystemInfos.HD MU_SystemInfos'>
[Skin] Attribute not implemented: scrollbarMode value: showOnDemand
[Skin] Attribute not implemented: scrollbarMode value: showOnDemand
main thread is non-idle! display spinner!


Ciao ...

morly
17.12.2013, 00:53
sorry, using which version, finally??

arci
17.12.2013, 01:13
sorry, using which version, finally??

Hi @morly

The before test refer to version 11904 oe 801 ...

If I have time ... I will test the new version 11906 oe 802 ... that from few time ... it's on server ! :)

Ciao ...

morly
17.12.2013, 01:26
yeah - please test the new version - significant chances inside... ;)

arci
17.12.2013, 02:28
yeah - please test the new version - significant chances inside... ;)

New version 11906 oe 802:

- aio grab (fixed) OK

Bug: Confirm issue on HDMU Center Info System !

GoodNight :cool:

Ciao ...

marep
17.12.2013, 13:41
Hello.
First: it is very good and stable firmware, so thank You very much
second: how can I change back to TV mode from radio mode? How can I change audio track? (on other enigmas - yellow key)
third: there is a problem with ocasionally freezing screen for a half second - maybe it is kernel 3.9.2 or driver problem. This problem is the same in OpenATV image with 3.9.2 kernel.

Greetings,
marep

carzio
18.12.2013, 18:49
hallo
image ok tested:):):) azbox premium hd
openvpn is out ??



I installed manually CCcaminfo wrong 'on this image?
solutions?

fred003
23.12.2013, 02:42
Hola.la 11917 in system information discharge is 11906

macmanolo
23.12.2013, 19:36
HDMU 11917 oe 809 ... bug


-HDMU info system ... does not work ... (E2 idle-spinner loop), immer noch...

mfg

tanja10
30.12.2013, 17:54
das Image gefällt mir sehr gut
THX

macmanolo
04.01.2014, 14:48
HDMU_11939_AzboxHD_OE_833_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11939_AzboxHD_OE_833_Flash.zip) instaliert und...

Das HDMU-Center hat in Menu Info system immer noch den gleichen fehler (E2 idle-spinner loop), da hilft nur hinten aus und an machen.

mfg

kapios
04.01.2014, 16:41
my internal hard drive no power off. always spins

macmanolo
04.01.2014, 18:31
The internal drive of my azbox if put into standby after 10 minutes of inactivity.

bonkel
05.01.2014, 15:06
HDMU_11939_AzboxHD_OE_833_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11939_AzboxHD_OE_833_Flash.zip) instaliert und...

Das HDMU-Center hat in Menu Info system immer noch den gleichen fehler (E2 idle-spinner loop), da hilft nur hinten aus und an machen.

mfg
hast du das Image auf dem dom drauf ?

macmanolo
05.01.2014, 15:14
Jain, ich habe einem 8GB sdkarte in einen dom adapter.

Wird wie mit einen echten dom instaliert aber so als were einen cf karte gehandelt vileicht liegt es daran?

blueice_haller
06.01.2014, 12:33
Hallo,
ich habe gerade mit Azup das Image HDMU_11939_AzboxHD_OE_833_Flash (http://www.hdmedia-universe.com/board/pages.php?pageid=1&box=azboxhd) auf den 2GB DOM in der AZbox Premium HD Plus geflasht.
Es startet, im Display steht VFD READY! und über HDMI wird das Bootlogo (die Erde und in Brauntönen Gaswolken) angezeigt.
Aber der Einrichtungsassistent erscheint nicht.

arci
06.01.2014, 12:46
Try to turn off the receiver by pressing the rear button ON/OFF ... and retry the boot for the first setup wizard !

blueice_haller
06.01.2014, 16:32
Funktioniert das HBBTV-Plugin (so wie im opena.tv-Image)?

bonkel
06.01.2014, 19:07
probieren geht über studieren :)

zeini
06.01.2014, 19:51
Funktioniert das HBBTV-Plugin (so wie im opena.tv-Image)?
Da wirst du nicht viel Freude haben auf dieser Box mit HbbTV. So wie im OpenATV. Die Box ist einfach zu brustschwach dafür.

kapios
06.01.2014, 20:55
The internal drive of my azbox if put into standby after 10 minutes of inactivity.

The internal drive of my azbox if put standby in 10 minutes, not stop
I do not know if something is wrong because I have the image in usb.
but in all the image that I have in usb the internal drive standby after 10 minutes

macmanolo
11.01.2014, 13:24
HDMU_11939_AzboxHD_OE_833_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11939_AzboxHD_OE_833_Flash.zip) instaliert und...

Das HDMU-Center hat in Menu Info system immer noch den gleichen fehler (E2 idle-spinner loop), da hilft nur hinten aus und an machen.

mfg
Habe dem HDMU_11949_AzboxHD_OE_851_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11949_AzboxHD_OE_851_Flash.zip) geflash, keine settings engespielt alles rein sauber von null auf configuriert und der fehler besteht immer noch, dieses mal habe ich auch ( zum sicher sein) auch auf einen original DOM geflash und der resultat is der gleiche, ich kann nich sagen seit wan das pasiert aber am anfang, also mit der ersten versionen pasiete das nicht, eine idee woran das ligen kann?

mfg.

macmanolo
02.02.2014, 16:44
Habe heute mal herunprobiert mit de AZboxHD, und zur versuchen heraus zu finden warun der oben genante fehler aufkom, nun nach mehrere flash versuche mit versidene versionen bin auf folgendes gekommen:

Mit firm HDMU_11893_AzboxHD_OE_858_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11893_AzboxHD_OE_858_Flash.zip) funkzioniert alles... HDMU center - System Info OK, BonkelMediacenter OK, Wetter OK

Von firm HDMU_11906_AzboxHD_OE_802_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11906_AzboxHD_OE_802_Flash.zip) bis firm HDMU_11949_AzboxHD_OE_851_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11949_AzboxHD_OE_851_Flash.zip) HDMU Center - System Info nicht ok (kom dauer spinner), BonkelMediacenter WS, Wetter nicht ok (kom dauer spinner)

Habe Jetz 11893 in DOM gelassen da bei den alles gut leuft (auser den Cover in Mediacenter)

Lege log von WS bei.

mfg

macmanolo
13.02.2014, 22:49
Habe gerade gesehen das es neue image für den AZBoxHD gebt, möchte drauf aufmerksanmachen das es warseinlich was sief gegangen ist da die datei viel zu gross ist:


HDMU_12047_AzboxHD_OE_1206_Flash.zip

13-Feb-2014 20:42

123.27 MB




Ich kan das nicht probieren da ich an de AZ nur an wochenende dran komme, aber diesen wochenende bin ich auf eine reise und komme nicht dazu.

mfg

majid.209.mt
16.02.2014, 09:11
hi
for AZBOX ME please.
th@:ba226:

macmanolo
18.02.2014, 21:18
Bonkel, welchen Kernel benutz das image: HDMU_12047_AzboxHD_OE_1206_Flash.zip 13-Feb-2014 20:42 habe gelessen das diesen firm wieder zurück auf kernel 3.3.1 gegangen ist, ist das so, oder ist es bein kernel 3.9.2 geblieben?

mfg.

Neo64
18.02.2014, 22:28
Dont work this soft = 123 MB ?????? file patch for Azbox verry BIG file


kernel 3.3.1 patch =49Mb
kernel 3.9.2 patch = 56 Mb


??????????= 123 Mb

bonkel
18.02.2014, 22:31
Bonkel, welchen Kernel benutz das image: HDMU_12047_AzboxHD_OE_1206_Flash.zip 13-Feb-2014 20:42 habe gelessen das diesen firm wieder zurück auf kernel 3.3.1 gegangen ist, ist das so, oder ist es bein kernel 3.9.2 geblieben?

mfg.
ja zum test mal 3.3.1

Neo64
18.02.2014, 22:34
Dont Arbeit dieser weichen = 123 MB??? Datei-Patch für Azbox verry BIG-Datei


Kernel-Patch 3.3.1 = 49MB
Kernel-Patch 3.9.2 = 56 Mb


????? = 123 Mb

macmanolo
19.02.2014, 22:45
Bonkel, etwas funkzioniert nicht mit der aufbau der images für de AZBoxHD, die images sind viel zur gross über 120MG, wie die leute hier http://www.hdmedia-universe.com/board/showthread.php?6012-image sagen können die nicht mit azup geflash werden, bitte wen du zeit hast werfe mal einen blick drauf.

Ich werde es am wochenende auch mal selber probieren aber wen es bei denen nicht funzioniert hat, denke ich wird es bei mir auch nicht funzen.

mfg

neipe
19.02.2014, 23:03
Haben wir schon gemerkt das da irgendwas faul ist,
Bonkel schaut sich die Sache an , wenner bissl Luft hat.

zeini
19.02.2014, 23:09
Ja, so ein großes Image läßt sich nicht mehr flashen. Genau dieses Problem hatte auch Captain von OpenATV Anfangs für das 4.0 Image mit dem 3.9.2 Kernel. Mit dem 3.3.1 Kernel funzte es dann aber.

Neo64
19.02.2014, 23:48
OpenATV 4.0 kernel 3.3.1 AzboxHD=48.465 KB legal Image
http://images.mynonpublic.com/openatv/beta/index.php?open=azboxhd

ravemaster
21.02.2014, 13:48
@bonkel

Gibt es schon was neues wegen dem zu großen Image? :rolleyes:
Ich hab am WE mal eines der älteren Testen können und es hat mir bis auf die Keymap gut gefallen. Wäre super, wenn es auch ein funktionierendes 3.3.1er Kernelimage gäbe.

arci
21.02.2014, 14:54
@ bonkel

Check the build environment ... on the cramfs there is an origin code of sources & include data of cross compiling system ! :)

Ciao ...

bonkel
21.02.2014, 16:46
mh i see that captain use gcc 4.5.1??
or what is the problem, i dont see a mistake in image build, so i dont know why its so big,

we use gcc4.8.2 and i will not downgrade it to 4.5.1

Neo64
21.02.2014, 20:55
firmware is BIG,dont work

cimi
22.02.2014, 10:33
hi! i have installed Hdmu firmware in pen usb , but driver pl2303 is not installed, : cat /proc/bus/usb/devices
T: Bus=01 Lev=03 Prnt=05 Port=01 Cnt=01 Dev#= 9 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=067b ProdID=2303 Rev= 3.00
S: Manufacturer=Prolific Technology Inc.
S: Product=USB-Serial Controller
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 10 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms

Help me ,what this is the way for install driver pl2303 in my image in pen ?
thanks for help and for this nice image

macmanolo
26.02.2014, 21:43
mh i see that captain use gcc 4.5.1??
or what is the problem, i dont see a mistake in image build, so i dont know why its so big,

we use gcc4.8.2 and i will not downgrade it to 4.5.1

¿Ist da was neuers mit der images für den AZBoxHD?

¿können wir dem nächts auf neue images hoffen?

¿Oder ist da iergend wie ein grosses problem aufgetauch?

mfg.

bonkel
26.02.2014, 22:02
zu dem stand hat sich nix geändert...ich seh wie gesagt keinen fehler und ich werde das gcc nich downgraden

redoom
28.02.2014, 19:02
Gerade mal das HDMU_12049_AzboxHD_OE_1218_Flash.zip auf eine azbox hd premium geflasht.

opkg und vsftpd liefen nicht.



root@azboxhd:/# opkg update
Collected errors:
* opkg_conf_load: Could not create lock file /var/lib/opkg/lock: No such file o
r directory.


Lösung: mkdir /var/lib/opkg/


[R] Verbindung herstellen zu 192.168.0.161 -> IP=192.168.0.161 PORT=21
[R] Verbunden mit 192.168.0.161
[R] 500 OOPS: vsftpd: not found: directory given in 'secure_chroot_dir':/var/share/empty
[R] Verbindung fehlgeschlagen

Lösung: opkg install vsftpd


Kann da beim flashen etwas schief gelaufen sein oder liegts am image?

macmanolo
28.02.2014, 20:04
Ich glaube das kann nicht am firm liegen da man es wegen hiergend einen fehler in der grösse der fiele nicht flashen kann.

redoom
28.02.2014, 20:06
habe es geflasht :-) Aber ist meine erste azbox, kann mich auch nicht sonderlich mit den Kisten anfreunden *g*

ravemaster
28.02.2014, 20:06
Konntest Du das Image mit dieser Größe überhaupt flashen?

redoom
28.02.2014, 20:15
In der Fehlermeldung stand doch das Problem, denke mal Flash zu klein, steck einen USB Stick an und installier es darauf.

macmanolo
28.02.2014, 20:22
Wie du hier http://www.hdmedia-universe.com/board/showthread.php?5167-Image-online&p=70789&viewfull=1#post70789 sehen kanst, ich habe es versuch auf einen pendrive im USB zur flashen, aber die datei ist zur gross und bricht bein 69,5% ab, die probe habe ich vor einen viertelstunde gemacht :eek:

mfg

arci
28.02.2014, 20:22
Don't make believe the wrong things ... to people! :mad:

Who has tried ... has installed on DOM more larger or pendrive with using scripts to change the size of the partitions for it working !

redoom
28.02.2014, 20:37
Iam not familar with this stbs, so calm down!

Image flashed but some things missing, e.g. opkg, vsftp, webinterface dont work. Some other stuff too i guess. But stb booted and operated.

Installed now HDMU_11949_AzboxHD_OE_851_Flash, work for me. Image has half the size than newer ones.

If youre the azbox expert please explain how to do, and stop spamming :-)

arci
28.02.2014, 20:53
Gerade mal das HDMU_12049_AzboxHD_OE_1218_Flash.zip auf eine azbox hd premium geflasht.

opkg und vsftpd liefen nicht.



root@azboxhd:/# opkg update
Collected errors:
* opkg_conf_load: Could not create lock file /var/lib/opkg/lock: No such file o
r directory.


Lösung: mkdir /var/lib/opkg/


[R] Verbindung herstellen zu 192.168.0.161 -> IP=192.168.0.161 PORT=21
[R] Verbunden mit 192.168.0.161
[R] 500 OOPS: vsftpd: not found: directory given in 'secure_chroot_dir':/var/share/empty
[R] Verbindung fehlgeschlagen

Lösung: opkg install vsftpd


Kann da beim flashen etwas schief gelaufen sein oder liegts am image?


Iam not familar with this stbs, so calm down!

Image flashed but some things missing, e.g. opkg, vsftp, webinterface dont work. Some other stuff too i guess. But stb booted and operated.

Installed now HDMU_11949_AzboxHD_OE_851_Flash, work for me. Image has half the size than newer ones.

If youre the azbox expert please explain how to do, and stop spamming :-)

I do spamming?

My friend ... are years that are behind the AZBox's world ... and everything I've learned I sent to the community!

From your statements, users are thinking that the new versions (12047 and 12049) were you able to install them!

Only now I read that you're trying the 11949 version that can be installed by all of us!

Saluti ...

redoom
28.02.2014, 21:47
First, we are not friends.

Second, i installed the HDMU_12049_AzboxHD_OE_1218_Flash too, but with errors. Try yourself if you dont believe. Choose USB & hit update Kernel/E2, when the error Message appears (near 68%) klick ok and be patient, dont abort, azup will continue. Stb will reboot, be patient again, no bootlogo, nothing in vfd, after a few minutes spinner and after that start assistand will appear.

STB boot and basics are running fine, but as said, its corrupted. Could be fixed manually, but that dont make sense, the fault is somewhere else.

arci
28.02.2014, 22:15
Sorry ... is correct ... we are not friends!

Good test with your AZBox ...

Joker7
28.02.2014, 22:26
@redoom

... ist das Image im Flash danach noch voll ok ?

...hab da irgendwo gelesen..finde es aber leider nicht mehr...das es sich danach bzgl. der Bildeinstellungen usw. irgendwie "komisch" verhält..

redoom
28.02.2014, 22:48
Nein das 12049 ist nicht ok, azup bricht anscheinend ab bevor es komplett installiert ist. Reicht zum booten, hatte opkg und ftp gefixt, danach dann festgestellt das opkg keine installierten pakete, bzw nur die nach dem fix installieren auflistet. Danach dachte ich mir dann warum das leben schwer machen, ist nicht meine box. Also das 11949 geflasht und eingerichtet.

Joker7
28.02.2014, 23:06
THX @redoom

..meine Frage bezog sich zwar auf das nachträgliche Verhalten eines schon im Flash befindlichen Image ..nachdem auf dem USB-Stick das aktuelle HDMU installiert wurde...aber ist nicht so wichtig...war eher ne theoretische Frage,da ich praktisch da eh nicht mitreden kann...

redoom
28.02.2014, 23:11
Im Flash war irgend ein Fremdimage, habe nach dem gebastel nicht wieder darauf zurück gegriffen. Stick rausgezogen und die Kiste ist mit der IP im Display stehen geblieben. dann das HDMU in den Flash gepappt und gut war.

redoom
01.03.2014, 01:18
Ein opkg-upgrade unter 11949 führt zu einer box die nicht mehr bootet da die installation von base-files - 3.0.14-r11958 - 3.0.14-r12052 hängen bleibt.

Wer trotzdem ein aktuelles image haben möchte kann mal den befehl per telnet absetzen:

Vorher opkg update



opkg install libav enigma2-plugin-extensions-mediascanner libcom-err2 tslib-conf libavformat53 liborc-test-0.4-0 openssl libavdevice53 dbus-1 modutils-initscripts libavutil51 enigma2-plugin-systemplugins-fastscan enigma2-plugin-systemplugins-hotplug libdbus-1-3 tzdata openssl-conf enigma2-plugin-systemplugins-cablescan libdvdread4 libts-1.0-0 dropbear curl enigma2-plugin-extensions-cutlisteditor enigma2-plugin-systemplugins-positionersetup enigma2-hdmu libavcodec53 enigma2-fonts base-passwd e2fsprogs-e2fsck kmod libdvdnav4 enigma2-plugin-systemplugins-videomode libswscale2 libext2fs2 enigma2-plugin-systemplugins-softwaremanager libavfilter2 tuxbox-common libsoup-2.4 libcurl4 enigma2 liborc-0.4-0 boxmodel enigma2-plugin-systemplugins-networkwizard file libglib-2.0-0 libtuxtxt32bpp0 libtasn1-6 netbase e2fsprogs-tune2fs enigma2-plugin-systemplugins-skinselector kernel-module-boxmodel zram e2fsprogs-mke2fs libpostproc52 aio-grab enigma2-plugin-extensions-graphmultiepg libtuxtxt0 libe2p2 enigma2-plugin-systemplugins-satfinder libfreetype6 enigma2-plugin-systemplugins-videotune



Ist es eigentlich normal das die Umschaltzeiten bei der Box so mies sind?

zeini
01.03.2014, 01:43
Was verstehst du unter mies?
Die schnellsten Boxen sind es nicht. Aber direkt als mies würde ich das auch nicht sehen.

redoom
01.03.2014, 01:53
[QUOTE=zeini;70814]Was verstehst du unter mies?/QUOTE]

3-5 Sekunden bei FTA

zeini
01.03.2014, 12:02
Nun 2-4 Sekunden habe ich auch. Mein nagelneuer 4K TV hat übrigens auch so lange Umschaltzeiten. :(

Macbest
01.03.2014, 15:44
2-4 Sekunden ist nicht so schön.....und das bei FTA. :(

macmanolo
01.03.2014, 16:08
Mit HDMU 11893_856 Starten vom hinteren knopf bist image vom Sat mit Oscam erscheint 1 minute und 18 sekunden (mit starupvideo von HDMU), umschaltzeiten bei FTA sender in SD qualität etwa 1 sekunde bei HD qualität kappe 2 sekunde, versucht mit ARD/ZDF.

mfg

sofrenic
23.03.2014, 15:14
Ich kann meine WiFi-Treiber für AZBox HD nicht finden (HDMU 07.01.2014)

macmanolo
27.03.2014, 14:30
*Bonkel, wie geths mit den AZBoxHD, wierd es neuer images geben oder is diese leitung in standby?

mfg.

blueice_haller
18.04.2014, 01:07
Hallo,
ich habe einen 2 GB DOM und bei mir kommt bei HDMU_12049_AzboxHD_OE_1218_Flash (http://www.hdmedia-universe.com/board/pages.php?pageid=1&box=azboxhd) die Fehlermeldung dass das Image zu groß sei und ich USB nutzen soll.
Ich habe es gerade mit einem 2 GB USB Stick getestet. Erst Only Kernel und dann Device USB und dann kam could not write file und danach An error occured while copying the kernel 3 unsuccessful attempts oder ich soll einen anderen Stick verwenden weil er möglicherweise zu langsam ist.
Auf dem USB Stick wurden 4 Partitionen angelegt.
Ich habe nun mehrere Möglichkeiten:
a) Ich bitte um ein Image für DOM
b) Ich installiere ein anderes Image z.B. openATV mit Format Extended Partition, formatiere die Partitionen und installiere dann HDMU ohne dem Format Extended Partition. Ich erhoffe mir dass das Image dann in den DOM passt.
c) eine Anleitung wie ich die patch.e2 entpacken, anpassen und packen kann. Ich habe ein Tool gefunden: unpack_e2.c.zip

zeini
18.04.2014, 09:56
Flashe das HDMU 11949 Image (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_11949_AzboxHD_OE_851_Flash.zip). Und mach dann ein Onlineupdate.
Die 12047 und 12049 dürften von der Größe her tatsächlich nicht passen. Da ist wohl was beim Bauen daneben gegangen.

blueice_haller
18.04.2014, 13:15
Danke. Und dann bin ich auf dem selben Stand? Beim ersten Versuch ist bei den base-files über eine halbe Stunde nichts passiert.
Das habe ich dann abgebrochen und nun kommt VFD READY! und im TV BOOTING.... Ich flashe nochmal und bleibe erstmal bei 11949.

Wo kann ich die Gelbe Taste auf Tonspur (anstatt Mediacenter) umstellen?

Und wo kann ich den Lüfter im Standby ausschalten?
enigma2-plugin-systemplugins-rtisys_git13+e368824-r16_azboxhd.ipk
enigma2-plugin-extensions-infopanel_3.0+git18107+753a705-r3_azboxhd.ipk

Warum geht meine HDD nicht in den Standby?

Ich weiß jetzt warum das Image so groß ist:
HDMU_12049_AzboxHD_OE_1218_Flash/cram.img/usr/src/kernel/ <-- Hier liegen viele Dateien
HDMU_11949_AzboxHD_OE_851_Flash/cram.img/usr/src/ <-- Dieses Verzeichnis ist leer

Lucjan
22.04.2014, 20:22
HDMU_12302 AzboxHD ist Top bis auf Radio.:sm49::sm49:

bonkel
23.04.2014, 15:37
neustes image schon getestet?

arci
23.04.2014, 16:33
neustes image schon getestet?

Yes ... it works [12316 oe 1344]!

I could not try everything on AZ Ultra HD version ... :)

I had some trouble finding the right combination for the frequency of the card reader with oscam8837 and TivuSat N3 card (the only combination that works is cardmhz = 368 mhz = 500) while other from feed:ymod not SC init, 3c ok (always) ... but the ecm time is up approximately 650 ms and occasionally produces video freeze!

The zap time (approximately):

crypt to crypt = 6 s
crypt to fta = 3 s
fta to fta = 2 s

- HDMU Media Center = OK [AVI-MKV-Mp3 simple file play test] and TS play from CIFS Net Mount VodafoneTV(DVB-T) recordings storage device !

Ciao & Thanks

macmanolo
23.04.2014, 16:41
Ja, heute kurzt image "HDMU_12302_AzboxHD_OE_1343_Flash" getestet und alles was ich normaleweise benutze leuft wie es sein sollte, für mich nach der "HDMU_11893_AzboxHD_OE_858_Flash" das beste image.

mfg.

PD. habe gesehen das es wieder eine neuer imege giebst werde es gleich mal einspielen und zur sehen wie dieses leuft.

PD2. Online update gemacht und alles leuft weiter so gut wie vorher...

sofrenic
23.04.2014, 22:24
HDMU_12316_AzboxHD_OE_1344_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_12316_AzboxHD_OE_1344_Flash.zip) WIfI NOT OK
HDMU_12302_AzboxHD_OE_1343_Flash.zip (http://images.hdmedia-universe.com/mips/azboxhd/HDMU_12302_AzboxHD_OE_1343_Flash.zip) WiFi not OK

Can't Connect to the Internet

bonkel
24.04.2014, 14:49
nothing changed with wifi..

sofrenic
24.04.2014, 23:34
Could not connect to the router. Version 851 is ok. Keymap for audio subtitle fix is stil required, hooked him

blueice_haller
21.05.2014, 01:59
I was wondering that after installing RTi-SYS Plugin I can't control the fan of my premium+ (Open Webif > Receiver-Informationen > Modell).
I'm new in developing python plugins and studied the code from RTi-SYS https://github.com/OpenAZBox/RTi-SYS.

In lines 307, 431, 446 and 575 of https://github.com/OpenAZBox/RTi-SYS/blob/master/plugin.py it tries to determine and assign the model type. Example line 307:

hw_type = HardwareInfo().get_device_name()
if hw_type == "me" or hw_type == "minime" :
self.LEDtimeTimer.callback.append(self.updateLED)
if hw_type == "minime" :
self.RtiminimeTimer.callback.append(self.updateCR)
elif hw_type == 'elite' or hw_type == 'premium' or hw_type == 'premium+' or hw_type == 'ultra' :
self.LEDtimeTimer.callback.append(self.updateLEDHD )
if hw_type == 'ultra' or hw_type == 'premium+':
self.FANtimeTimer.callback.append(self.updateFAN)

This is later important to get the correct entries in Einstellungen > System > ...

def Plugins(**kwargs):
hw_type = HardwareInfo().get_device_name()
if hw_type == 'ultra' or hw_type == 'premium+':
return [
PluginDescriptor(name="FanCtrl", description="FAN Controll", where = PluginDescriptor.WHERE_MENU, fnc=startSetup),
PluginDescriptor(name="AVp_setup", description="scan mode & interlaced algo", where = PluginDescriptor.WHERE_MENU, fnc=startSetup2),
PluginDescriptor(where=[PluginDescriptor.WHERE_SESSIONSTART], fnc=sessionstart)
]
elif hw_type == 'minime':
return [
PluginDescriptor(name="CRClock_setup", description="CR set freq", where = PluginDescriptor.WHERE_MENU, fnc=startSetup1),
PluginDescriptor(name="AVp_setup", description="scan mode & interlaced algo", where = PluginDescriptor.WHERE_MENU, fnc=startSetup2),
PluginDescriptor(where=[PluginDescriptor.WHERE_SESSIONSTART], fnc=sessionstart)
]
else:
return [
PluginDescriptor(name="AVp_setup", description="scan mode & interlaced algo", where = PluginDescriptor.WHERE_MENU, fnc=startSetup2),
PluginDescriptor(where=[PluginDescriptor.WHERE_SESSIONSTART], fnc=sessionstart)
]

Because I only get the [A/V settings +] entry something went wrong: I think that it runs in the last else in line 588.

Because I dont't know where to find the missing function HardwareInfo(): hw_type = HardwareInfo().get_device_name() I easily assign it manually to hw_type = premium+ 4 times in the lines 307, 431, 446 and 575.
Does anybody know an alternative to determine this? Which function does Open Webif use to determines it?

And yes, if I change the code, delete the plugin.pyo and restart the box I have also the entry [Fan Set] in OSD and can change anything.

I have tested it and it works.

That what I heard then was the HDD (ST3500630AS) which goes in standby after some minutes with my init-script (http://www.hdmedia-universe.com/board/showthread.php?5167-Image-online&p=81053&viewfull=1#post81053).[/B]

morly
12.06.2014, 22:35
Brauch kurze Hilfe,
das Image besteht aus cram.img und kernel.img
Wie können die auf welche Partition geflasht werden (via telnet)??
Wohl besser nicht via dd, oder?

macmanolo
12.06.2014, 22:48
Wird nomaleweise mit en eigenes program geflash "AzUp 2.2.7" ist ein windows program :-( früer gabs einen in java aber der funzioniert jetz nicht mehr?

mfg

morly
12.06.2014, 22:54
hab ja das Ding entpackt und die beiden Files liegen, muss nur wissen welches mtd wofür ist (vermute kernel=mtd4 und rootfs=mtd0)

macmanolo
12.06.2014, 23:03
Morgen nachmitag komme ich an den az dran, dan kann ich ja nachsehen was du mir sagts.

mfg

morly
13.06.2014, 09:15
Interessant wäre wo der Kernel sitzt und wo rootfs.
Dabei könnte helfen:

cat /proc/cmdline

Und eben wie die Dinger dann geflasht werden ;)

zeini
13.06.2014, 10:37
Die "alten" Azboxen (Premium HD, Premium HD+, Elite HD und Ultra HD) sind Zicken beim flashen. Ich rate davon ab, das mit deinem Tool zu flashen. Beim Neuflashen wurden schon viele Boxen in die ewigen Jagdgründe geschickt.
Derzeit gibt es nur ein Tool, Azup 2.2.7, mit welchem man alle Images flashen kann. Es gab sicher 5 verschiedene Vorprodukte dieses Flashtools. Und das wurde immer nur deshalb erneuert, weil mit einem neuen Image meist mit neuem Kernel, das vorige Tool nicht mehr funzte und die Box nur mehr mittels JTAG wiederbelebt werden konnte, falls man mit dem "alten" Flashtool flashte.

Nichts desto trotz aber mal deine gewünschte Abfrage


root@azboxhd:~# cat /proc/cmdline
mem=107m console=ttyS0,115200

morly
13.06.2014, 11:09
Verstanden - Danke, dann lass ich das mal :)
Also Box kommt rein aber ohne Flash/Backup Support

macmanolo
13.06.2014, 11:12
Backup wurde aber schon eine gutte sache sein, da es keine utility dafür giebt.

Auch wen man das mit azup flashen müste

morly
13.06.2014, 11:20
dann mach mir mal von jeder mtd einen dd dump (bitte einfach mtd0-mtdx benennen) und lad mir diese hoch, teste dann was...

macmanolo
13.06.2014, 13:52
dann mach mir mal von jeder mtd einen dd dump (bitte einfach mtd0-mtdx benennen) und lad mir diese hoch, teste dann was...
OK, jetz sietze ich vor den AzBoxHD wie sollte ich das was du meints machen?

Von Linux aus? von Telnet?, mit ftp programm?

mfg

blueice_haller
29.06.2014, 14:34
Hallo,
wo wird denn festgelegt wie die Festplatte gemountet wird? In /etc/fstab steht nichts davon:

rootfs / auto defaults 1 1
proc /proc proc defaults 0 0
devpts /dev/pts devpts mode=0620,gid=5 0 0
usbdevfs /proc/bus/usb usbdevfs noauto 0 0
tmpfs /var/volatile tmpfs defaults 0 0
Ausgabe von mount: /dev/hdb1 on /media/hdb1 type ext3 (rw,relatime,errors=continue,user_xattr,barrier=1, data=ordered)
Ausgabe von blkid:

/dev/hdb1: UUID="d0e57e92-dff5-407f-aca2-1f9fa5d69e53" TYPE="ext3"
/dev/hda2: UUID="482d897c-e88e-4ec4-a326-813ddff7de47" TYPE="ext2"
/dev/hda1: UUID="585544f9-7062-4e23-9002-2f83ee5e805d" TYPE="ext3"
/dev/hda3: UUID="6a6444b1-f689-4b06-a97a-2f7b54e79fed" TYPE="swap"
/dev/hda5: UUID="fb4bb225-89ff-4c8f-a527-b10832e16a88" TYPE="ext3"
/dev/mtdblock/4: LABEL="MIPS_LINUX_XRPC" TYPE="romfs"
/dev/mtdblock/3: LABEL="YAMON_XRPC" TYPE="romfs"
Ziel: Ich möchte dass der Symlink /media/hdd wieder funktioniert. Ich könnte das auch in einem Startskript hinterlegen.
Ich habe jetzt einen Eintrag in der /etc/fstab erstellt:

UUID=d0e57e92-dff5-407f-aca2-1f9fa5d69e53 /media/hdd ext3 defaults 0 0

Irgendwas stimmt mit dem nfsserver nicht:

/etc/init.d/nfsserver restart
stopping mountd: done
stopping nfsd: done
starting 8 nfsd kernel threads: rpc.nfsd: writing fd to kernel failed: errno 146 (Connection refused)
rpc.nfsd: unable to set any sockets for nfsd

opkg install --force-reinstall rpcbind
Downloading http://hdmu.de/mipsv2/azboxhd/mips32el/rpcbind_0.2.1-r0_mips32el.ipk.
Reinstalling rpcbind (0.2.1-r0) on root.
Stopping rpcbind daemon...
not running.
update-rc.d: /etc/init.d/rpcbind exists during rc.d purge (continuing)
Removing any system startup links for rpcbind ...
/etc/rc0.d/K60rpcbind
/etc/rc1.d/K60rpcbind
/etc/rc2.d/S12rpcbind
/etc/rc3.d/S12rpcbind
/etc/rc4.d/S12rpcbind
/etc/rc5.d/S12rpcbind
/etc/rc6.d/K60rpcbind
Running useradd commands...
NOTE: Performing useradd with [ --system --no-create-home --shell /bin/false --user-group rpc] and 10 times of retry
WARNING: user rpc already exists, not re-creating it
Configuring rpcbind.
Adding system startup for /etc/init.d/rpcbind.
Starting rpcbind daemon...rpcbind: fork failed: No such device
done.

macmanolo
29.06.2014, 20:50
Schau mal hier wegen die platte http://www.hdmedia-universe.com/board/showthread.php?2013-Festplatte-initialisieren-oder-wie-bekomme-ich-meine-HDD-eingebunden

mfg

blueice_haller
30.06.2014, 08:46
Hallo macmanolo,
es hat bereits geklappt mit dem einbinden über /etc/fstab aber der nfsserver startet nicht.
Ich habe in einem Forum gelesen dass es mit rpcbind_0.2.1-r4 wieder funktioniert aber das ist noch nicht auf dem Feed.

kapios
30.06.2014, 12:30
the problem with the internal hard drive with not go in standby Corrected?

blueice_haller
30.06.2014, 22:08
Hello kapios,
my solution for this problem:
1. create/edit file: /etc/init.d/hdparm

#!/bin/sh

ROOTHDD=/dev/hda
MOVIEHDD=/dev/hdb
ALLHDD="$ROOTHDD $MOVIEHDD"
STANDBYTIMEOUT=180 # 180 means 15 minutes

set -e

case "$1" in
start)
$0 setstandbytimeout
;;
setstandbytimeout)
hdparm -S $STANDBYTIMEOUT $MOVIEHDD
;;
status)
hdparm -C $ALLHDD
;;
nostandby)
hdparm -S 0 $MOVIEHDD
;;
*)
echo "Usage: $0 {status|setstandbytimeout|nostandby}"
exit 1
;;
esac

exit 0
2. Give execute rights
chmod +x /etc/init.d/hdparm
3. Create symlink to execute the script at boot time (I don't know if the runlevel 08 is optimal):

ln -s /etc/init.d/hdparm /etc/rcS.d/S08hdparm
4. For testing you can execute the script:

/etc/init.d/hdparm start

arci
17.07.2014, 23:18
Hi

HDMU_12690_AzboxHD_OE_1595

... Few Test to keep the memory ...

- HDMU Media Center (Web Radio fixed)
- WiFi WLAN (not fixed)
- Switch TV/Radio channel list (not fixed)

Ciao ...

ravemaster
09.08.2014, 07:03
@bonkel

Könntest du dir bitte mal das Problem mit dem HDD-Standby ansehen? Die läuft immer durch. Ich nutze das Image auf meiner HD. Es ist um einiges speicherschonender als andere.
Es nervt aber, wenn die HDD immer durchläuft (Box im Schlafzimmer) :eek:
Achja und das Onlineupdate funktioniert nicht richtig.

7898

Besten Dank

santa
09.08.2014, 08:51
Schau doch mal ob die Befehle sdparm und hdparm vorhanden sind und ob du damit die HDD schlafen legen kannst

bonkel
09.08.2014, 11:29
wieso funktioniert das online update nicht richtig? die meldung ist absichtlich da
wenn was schief geht..........

und wie soll die hdd in den standby gehen, wenn das image drauf läuft?

arci
09.08.2014, 15:22
@bonkel

Test on AZBultra HDMU 12823 OE 1642 ... default HDMU config and definition xml ... without any other plugins !

With the latest merge from OpenPLi (from last week at now) ... with last "T2-Auto scan" code changes ... after an automatic search with the DVB-T tuner USB dongle (Aver Volar Green HD "AF9035") ... the channel selection always returns a message "Tuner failed" on any digital terrestrial channels stored !

This does not happen by making a manual single DVB-T scan by frequency or channel number !

Make it known to the Team OpenPLi!

Thank you & Ciao ...

lucek
09.08.2014, 16:18
Welche Plugin, um den Lüfter zu steuern, weil ich versuchte, ein paar und keiner von ihnen zu arbeiten. Hat jemand überprüft.

ravemaster
09.08.2014, 23:50
Das mit dem Update ist nun klar, aber das Image läuft doch im Dom und nicht auf der HDD. Die geht doch auch bei anderen Images in Standby.

blueice_haller
10.08.2014, 12:01
@ravemaster: Hast Du meinen Beitrag mit Skript für HDD Standby (http://www.hdmedia-universe.com/board/showthread.php?5167-Image-online&p=81053&viewfull=1#post81053) nicht gelesen? Dein Satz in #174 (http://www.hdmedia-universe.com/board/showthread.php?5167-Image-online&p=83528&viewfull=1#post83528) wurde wahrscheinlich anders interpretiert: mit HD meinst Du nicht HDD sondern das Modell. Und es ist klar sobald etwas auf die HDD zugreift fährt sie wieder hoch.

@lucek: Did you read my reply about controlling the FAN e.g. off in standby (http://www.hdmedia-universe.com/board/showthread.php?5167-Image-online&p=78242&viewfull=1#post78242)?

Es wäre nett wenn diese einzug in das nächste Image halten würden. Danke.

ravemaster
10.08.2014, 22:14
OK. Ich meine eine PremiumHD ( die Box). Das die eingebaute Festplatte immer läuft, ist denk ich mal ein Imagefehler. Das machen ja auch andere Images nicht. Ich hab auch Deinen Beitrag gelesen. Das ist dann maximal ein Workaraound und keine Lösung des Problems. Nichts für ungut, ich mag dieses Image, aber die Festplatte sollte im normalen TV-Betrieb nicht immer laufen. Die ist für Timeshift, Aufnahmen und Wiedergabe gedacht.

santa
10.08.2014, 22:27
du hast meine frage nicht beantwortet, deswegen jetzt noch mehr

ist sdparm und/oder hdparm auf der Box vorhanden?
kannst du per telnet die HDD damit zum schlafen bringen?
geht die HDD nie aus?
andere HDD mal getestet?

ravemaster
11.08.2014, 14:44
Sorry santa.

1.) hdparm ist vorhanden.
2.) Mit hdparm lässt sich HDD in Standby versetzen. (hdparm -y /dev/hdb1)
3.) Sobald die HDD mal erweckt wurde, geht sie nicht wieder aus.
4.) Test mit anderer HDD nicht durchgeführt. Die funktioniert super (auch mit anderen Images). :D

Ich hoffe, dass konnte helfen.

lucek
11.08.2014, 15:05
@blueice_haller (http://www.hdmedia-universe.com/board/member.php?6132-blueice_haller)
I used a plugin rtisys standby and works :)
Maybe in the next images will be repaired.

blueice_haller
13.08.2014, 00:21
Hallo ravemaster,
-y hält nur bis zum nächsten Zugriff.

-S setzt die Standby-Zeit des Gerätes. Nach der eingestellten Zeit fährt die Festplatte in den Ruhezustand (entspricht -y). Ein Wert von 0 schaltet diese Funktion aus, maximal bis 255. Die Einteilung ist nicht linear, man muss etwas probieren um auf die gewünschte Zeit zu kommen.
-y setzt das Laufwerk sofort in den Standby Modus, die Spindel stoppt dabei. Bei Zugriffen wacht es automatisch wieder auf.Die Standby-Zeit wird nach einem Neustart wieder zurckgesetzt, das heißt die HDD schaltet sich nicht aus. Aus diesem Grund habe ich ein init-Skript geschrieben welches beim booten die Standby-Zeit mit -S setzt.

ravemaster
13.08.2014, 05:07
@blueice_haller

Vielen Dank. Ich werde das Script als Workaround einsezten. Vielleicht wird das ja im Image auch noch behoben. :)

macmanolo
15.08.2014, 16:50
Habe heute OnlineUpdate gemacht und sehe das der platz im Flash völig voll benutz ist obwohl keine extra plugins instaliert sind, ist das normal?

7955

mfg

bonkel
15.08.2014, 16:56
Neu flashen und nochmal.schauen. Hab paar Sachen geupdated

ravemaster
15.08.2014, 17:33
@bonkel

Hast du zufällig auch was beim Festplattenstandby geändert? :rolleyes:
Bin auch gerade am neu flashen, wegen Speichermangel nach dem Update, dann könnte ich das gleich testen. :)

bonkel
15.08.2014, 17:37
nein---

ravemaster
15.08.2014, 17:44
Auch wenn das jetzt lästig erscheint, aber kommt da noch eine Änderung? Wäre super, wenn die HDD wieder in Standby gehen würde.

bonkel
15.08.2014, 17:55
Im Moment hab ich andere Sorgen

ravemaster
15.08.2014, 18:02
Ok.
Mit dem letzten Image vom 14. lassen sich keine Plugins mehr installieren. Opkg update hat nichts gebracht.
7956

macmanolo
15.08.2014, 18:51
So,habe den platzmangel gelöscht aber glaube das ist kein general lössung.

Habe einen sd-adapter als DOM mit eine 8GB sd karte, die hate eine partition für images von 170MB (nehme an das ist der platz das der original DOM von 250 MB für das image bereitstellt, und das ist mitleweile zur benig.

Habe lätzters image mit azup228 im DOM neu instaliert mit "Format Extended Partition" angekreuzt und sehe da jetz habe ich eine partition von 325 MB und nur 53% besetz, das image benutz ohne plugins 173MB deswegen war ja kein platz mehr da.

Die lössung besteht entweder mann erweiter der DOM oder man instaliert das image im einen pendrive dan gehts.

mfg

macmanolo
18.08.2014, 14:13
Habe weitere tests gemacht, und bin auf folgendes gestossen, wen ich azup2.2.7 benutze dan wierd der platz im DOM sehr knap 7987 wie man sehen kann ist kein freie speicher mehr da, also man kan nicht mehr instalieren keine plugins etc...

Wen ich aber azup2.2.8 benutze dan habe ich doch eine menge freie speicher 7988

Auf einen USB-pendrive mit azup2.2.7 hat man doch noch platz 7989 sogar nach einen OnLineUpdate wie man sehen kann.

Und so habe ich beiden azup gehab2.2.7 7985 und 2.2.8 7986

Also bin ich zun abschluss gekommen das man azup2.2.8 benutzen sollte wen mann einen nicht original DOM hat, damit sollte man keine speicher probleme mehr haben, woran das liegt kann ich nicht sagen aber bei mir hats so geklapt.

mfg

ravemaster
19.08.2014, 05:33
AzUp 2.2.8 überprüft die größe des DOM's und teilt bei einem größeren als dem Standard (256MB) die Partitionen anders auf. Darum kann man so oder so 2.2.8 verwenden.

macmanolo
21.08.2014, 00:31
AzUp 2.2.8 überprüft die größe des DOM's und teilt bei einem größeren als dem Standard (256MB) die Partitionen anders auf. Darum kann man so oder so 2.2.8 verwenden.
Leider ist der AzUp 2.2.8 nicht so tool wie ich es mir gedach hatte .

Wen mann die AzUp 2.2.8 benutz hat man zwar mehr platz aber dafür kann man nicht mehr des multiboot benutzen :mad:

Eine idee warum das so ist?

mfg

ravemaster
21.08.2014, 05:27
Nein, leider nicht. Ich nutze kein Multiboot bei der PremiumHD. Der Boot über USB dauert mir einfach zu lange.

blueice_haller
30.08.2014, 13:17
Kann bitte jemand AzUp 2.2.8 in das UploadCenter (http://www.hdmedia-universe.com/board/UploadCenter.php) stellen? myazbox.de ist momentan nicht verfügbar.
Hat sich erledigt, hier ist es: AzUp 2.2.8 (http://www.hdmedia-universe.com/board/UploadCenter.php?do=download&downloadid=70)

Ich habe nun AzUp 2.2.8 HDMU_12927_AzboxHD_OE_1763_Flash geflasht.
Leider bekomme ich den nfsserver nicht zum laufen, siehe auch Post 168 (http://www.hdmedia-universe.com/board/showthread.php?5167-Image-online&p=80982&viewfull=1#post80982):

root@azboxhd:~# /etc/init.d/nfsserver restart
stopping mountd: done
stopping nfsd: done
starting 8 nfsd kernel threads: rpc.nfsd: writing fd to kernel failed: errno 146 (Connection refused)
rpc.nfsd: unable to set any sockets for nfsd

root@azboxhd:~# /etc/init.d/rpcbind start
Starting rpcbind daemon...done.
root@azboxhd:~# rpcbind: fork failed: No such device

root@azboxhd:~# opkg install portmap
Unknown package 'portmap'.
Collected errors:
* opkg_install_cmd: Cannot install package portmap.
root@azboxhd:~#

Folgende Pakete habe ich irgendwo gefunden: portmap-utils_6.0-r7_mips32el.ipk portmap_6.0-r7_mips32el.ipk

@bonkel: Kann es sein dass das NFS beim komplilieren des Kernel nicht ausgewählt ist? Kannst Du das bitte wieder einbauen? Oder verwendest Du den fertigen binären Kernel z.B. http://hdmu.de/mipsv2/azboxhd/azboxhd/kernel-image-3.3.1-opensat_3.3.1-r3.2_azboxhd.ipk und hast darauf keinen Einfluss?
An welchen Entwickler/Forum/Nutzer muss ich mich wenden?

blueice_haller
01.02.2015, 16:38
Hallo, ich wollte gerade das letzte Image HDMU_13668_AzboxHD_OE_1927_Flash (http://www.hdmedia-universe.com/board/pages.php?pageid=1&box=azboxhd) auf meinen 2GB DOM installieren, doch es kommt die Fehlermeldung: 14:32:35 > Image Size = 146 M -> Image too big
Hat das hiermit zu tun?

Dafür müste Bonkel der alte Gstreamer benutzen und ich glaube das wierd woll nicht sein.

mfg
Wenn ja wie groß muss der USB Stick sein?

macmanolo
01.02.2015, 16:45
Mit einen 1GB ist genug musst aber in multiboot instalieren und mit 2GB dom geht nicht ohne weiteres.

mfg.

blueice_haller
01.02.2015, 16:54
Ich habe nur einen USB Stick mit 8GB. Soll ich es dort installieren?

Ich habe es auf dem 8GB USB Stick installiert und es tritt das selbe Problem wie mit dem openATV Image auf:
Wenn man auf Radio schaltet dann dreht sich das HDMU-Logo links oben und man muss die Box neu starten.

Jemand hat dort einen Fix gebaut, bei welchem man enigma2 stoppt, /usr/bin/enigma2 austauscht und enigma2 wieder startet: Radio fix for openATV 4.2

ingo
30.12.2015, 12:07
No image azboxhd , azboxme , azboxminime. Was ist der grund?
http://www.hdmedia-universe.com/board/pages.php?pageid=1&box=azboxhd

ingo
14.01.2016, 13:12
Azbox Unterstützung wird fortgesetzt?

bonkel
14.01.2016, 13:40
Ja. Baut im Moment nur nicht

kapios
11.02.2016, 20:35
any news on update?

Joker7
17.02.2016, 00:37
..tja,der Frage schließe ich mich an.... baut das HDMU immer noch nicht? ...die "Iberer" und "Lateinamerikaner " laufen Euch sonst davon !!

Joker7
20.02.2016, 01:09
...was ich so an diesem Forum "Liebe" sind die sehr oft "ausbleibenden Antworten" oder soll ich besser sagen "Das völlige ignorieren von Fragen "

:D

bonkel
20.02.2016, 01:38
Sieht man docj das nichts baut. Steht ja nichts im tweet Feed und auxh ein Image ist nicht online. Also baut nicht

Joker7
20.02.2016, 02:04
..ok THX !..

...dann empfehle ich erstmal als "Übergangslösung" für die User die auch ein Multiboot nutzen möchten das openSpa-Image....und für die,die ohne große "Eigenarbeit" auch das WLAN Nutzen wollen, daß letzte PBNIGMA für die Azbox-Premium+.....

Joker7
20.02.2016, 03:33
..zumindest die HDMU-14700 (AzboxHD) hätte/könnte man ja zum Down bereitstellen...

... egal...I.Kant hatte schon recht mit seiner Kritik der Urteilskraft insbesondere mit "Kritik der praktischen Vernunft"...


..Sorry wieder mal etwas von "Sat-Thema" abgeschweift... aber muß auch mal sein ^^

bonkel
20.02.2016, 11:05
Problem. Ist das Images gelöscht werden wenn man die build Umgebung löscht

arci
20.02.2016, 11:47
Problem. Ist das Images gelöscht werden wenn man die build Umgebung löscht

Hi All ...

Here is the latest HDMU image version that works pretty well (dvb-t dongle included) ... but not for USB-storage device auto mount ... probably for not good features flags on kernel config ...

From my upload area [HDMU_14536_AzboxHD_OE_2430_Flash.zip]:


https://mega.nz/#!qA5WmR6Q!0NePhsBBgDj5R5aKd9Nsvapbw9NaKHUE6z-5Ev4f0_o


... many others would like that HDMU Team continue the project also on AZBox !!!


Ciao & Good Weekend ...

santa
21.02.2016, 21:47
bitte neue images testen, mal sehen ob die wieder laufen

Joker7
21.02.2016, 22:40
http://www.hdmedia-universe.com/board/showthread.php?9852-Hdmu-15079&p=111124#post111124

macmanolo
05.03.2016, 11:52
Hi morly Köntest du das für die folgende azboxhd images ändern?

Wen mann HDMU Images in Multi-Boot von OpenSpa instaliert, diese haben seit lange einen kleinen Fehler.

In der geänderte Datei "bootmisc.sh" gibt es eine "fi" zur viel, genau da wo es beginnt den Ordner für's multiboot zu montieren.

Damit nicht wierd der rest der datei nich ausgeführt, mann must nur der einen "fi" lössen damit alles wieder leuft.

Hier ein keinen teil wo der fehler auftrit


if test ! -L /tmp && test -d /var/tmp
then
rm -rf /tmp
ln -sf /var/tmp /tmp
fi

fi

if [ ! -d "/media/multiboot" ]; then
mkdir /media/multiboot
fi
# aqí se monta la carpeta hdd.
if [ ! -d "/media/hdd" ]; then
mkdir /media/hdd
fi

mfg,

Joker7
08.03.2016, 20:16
...hatte heute etwas Zeit und hab mal das "überflüssige" fi bei mir händisch raus gelöscht....

... jetzt geht natürlich auch wieder das WebIF ...war ja vorher der Fehler "exceptions.OSError: [Errno 2] No such file or directory: '/media/multiboot' "

THX @macmanolo !

bonkel
08.03.2016, 21:46
Im nächsten Image gefixed

kapios
01.09.2016, 12:43
HELLO

the team stop support azbox??

Tags-Images is empty

bonkel
01.09.2016, 18:13
No only.have no time AT the.moment

dazulrich
01.09.2016, 22:07
glad to hear you haven't abandoned the Azbox (yet).....
hope you'll find some time soon.

dazulrich
10.09.2016, 11:00
Hallo Bonkel. Danke für die neuen Images.
Gsteamer wird als v1.8.2 angezeigt.
du hattest vor ein paar Wochen angekündigt 1.9.1 einzubauen, Kannst du kurz bestätigen welche gst version drin ist?

bonkel
10.09.2016, 12:50
1.9.2 ist drin...keine ahnung warum falsch angezeigt wird

man kann ja in den paketen auch die version sehen

opkg list *gstreamer*

dazulrich
10.09.2016, 17:16
Danke. An "opkg list" hatte ich gar nicht gedacht.

humiboy
10.09.2016, 22:22
Hi,

ich habe da mal ne Frage bezüglich eines Plugins im Mediaportal.

Es gibt da so ein Plugin das nennt sich "Seriesever".

Dieses Plugin funktioniert aber nicht auf diversen Images mit Gstreamer 1.8.1 bzw 1.9.0.

Laut dhwz liegt es am Gstreamer das dieses Plugin nicht funktioniert.

Jetzt sehe ich das ihr im HDMU den Gstreamer 1.9.2 eingebaut habt. Könnt ihr das mal bei euch testen ob mit diesen neuen Gstreamer Seriesever im Mediaportal funktionkert?

Bei Vuplus Receivern und VTI Image mit altem Gstreamer funktionkert dieses HD Serien Plugin.

Ich danke schon mal im voraus

Joker7
10.09.2016, 22:56
"Könnt ihr das mal bei euch testen ob mit diesen neuen Gstreamer Seriesever im Mediaportal funktionkert?"

.... also ich hab leider derzeit sehr wenig Zeit und die Azbox gar nicht angeschlossen.... aber werden sich sicherlich andere finden,die Deine Bitte aufgreifen....

bonkel
11.09.2016, 11:04
Es gibt auch ffmpeg. Den man als Player auswählen kann. Serviceapp unter Extensions installieren und auswählen.

Anskar
11.09.2016, 11:39
Bei mir gestern mit GB Quad Plus ja nicht, @bonkel :confused:.

MfG

flac
11.09.2016, 12:25
Das muss ja auch nicht mit dem ffmpeg (exteplayer3) getestet werden, sondern mit GST und der aktuellen Version.

....und bitte beim Thema bleiben.




Gruß

flac

Anskar
11.09.2016, 12:47
Und von was hat bonkel geschrieben :rolleyes:?

Unter Serviceapp kann man nur zwischen exteplayer3 und gstplayer auswählen.
Und wie bonkel mir gestern per Skype schrieb ist exteplayer3 ffmpeg.

MfG

TheChip
11.09.2016, 15:41
@humiboy, wie wäre es denn, wenn Du selber mal testet und die anderen am Ergebnis teilhaben lässt? Oder lässt Du Dir auch sonst immer alles auf dem Silbertablett servieren? So ein Board lebt vom mitmachen.

Anskar
11.09.2016, 15:54
Laut flac zwar OT:rolleyes:

@humiboy, habe das 15888 Image von gestern auf der Box, aktuelles MP ist auch drauf.
Finde jetzt nicht "Seriesplugin" .
Wenn Du aber "Serienstream" meinst, das geht problemlos.
Getestet mit "Die Rosenheim-Cops".

In Serviceapp ist oben "Orginal" eingestellt, bei exteplayer3 geht's nicht.

Wenn Du was anderes meinst dann bitte genaue Bezeichnung.

MfG

humiboy
11.09.2016, 15:55
Es geht um "Seriesever" wie ich oben geschrieben habe.

Ich nutze ja eigentlich das openATV Image. Bevor ich selbst das HDMU installiere und selbst teste, dachte ich mir halt ich frage einfach mal hier nach ob es bei denen läuft die das HDMU Image eh schon drauf haben.

Mit Serviceapp und Extplayer3 geht überhaupt nix mit (openATV Image).

Ich hab aber von anderen Usern erfahren das es funktionieren soll mit HDMU und neusten Gstreamer. Wenn ihr das noch bestätigen könnt, brauche ich jetzt nicht extra das HDMU flashen um es heraus zu finden.

Anskar
11.09.2016, 15:59
Wo finde ich das, unter Grauzone nicht.

MfG

humiboy
11.09.2016, 16:05
Doch es ist unter Grauzone genau zwischen Serienstream und ShareDir

Anskar
11.09.2016, 16:31
Weiterhin OT.
Mein Fehler, freilich ist es da, habe irgendwie nach "Serienserver" gesucht ;-)

"Seriesever" funktioniert ebenfalls.
Getestet mit "Dr.House".

MfG

humiboy
11.09.2016, 17:01
Alles klar vielen Dank Anskar für deine Rückmeldung.

Jetzt weiss ich also das es am Gstreamer doch liegt.

Es hat nicht zufällig noch jemand das HDMU mit alten Gstreamer auf der Box der es auch noch mal kurz gegen testen kann?

flac
11.09.2016, 17:03
...so nun wissen wir das es bei uns funktioniert.

...hier kann wieder über die AzBoxHD diskutiert werden und nicht über irgendwelche Plugins im Mediaportal.



...diese Fragen hätte man im Mediaportal Thread stellen können.






Gruß

flac

zeini
11.09.2016, 17:23
Auch wenn es nicht direkt zur Azbox hier gehört.
Das Seriesever in einigen Images nicht funzt liegt nicht beim Mediaportal. Im OpenHDF funzt es nun auch mit GStreamer 1.8.1 nachdem Koivo da was nachgebessert hat.

dazulrich
11.09.2016, 19:52
@Bonkel und Team, welches Azbox dvbmediasink benutzt Ihr? https://github.com/dazulrich/gstreamer1.0-plugin-multibox-dvbmediasink oder nen anderes?

fen
11.09.2016, 20:46
Azbox Me
Image- HDMU_15888_AzboxMe_OE_2651


telnet doesn't work :(((

applet not found
Connection to host lost.