satbox
20.11.2013, 11:15
Hallo Leute
Meine IPBox 9000 hängt beim Laden des HDMU Image (HDMU_11684_E2_ipbox9000_211_git_5569_nodebug_mix_ USB.tar.gz)
Im Flash ist PGI 1.5 , hat jemand eine Idee wass ich machen kann, hatte bis jetzt nur Flash Images von PGI.
Danke im voraus
U-Boot 1.3.1-gbbd37f59 (Aug 14 2010 - 15:29:47) - stm23-2008-03-19
Board: cuberevo (0x2D42C041)
Board: 13 grid vfd front
DRAM: 128 MB
Flash: 32 MB
In: serial
Out: serial
Err: serial
Reserve 0x2010000 bytes from 0xa5ff0000 for DGS upgrade buffer.
Saving Environment to Flash...
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
Protected 1 sectors
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
1716071 bytes read
## Booting image at a5ff0000 ...
Image Name: Linux-2.6.32.59_stm24_0211
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1716007 Bytes = 1.6 MB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Warning: Unable to determine if kernel is built for 29- or 32-bit mode!
Starting kernel console=ttyAS1,115200 panic=3 root=/dev/sdb2 rw rootdelay=10 bigphysarea=1500 quiet - 0x00000000 - 0 ...
INIT: version 2.86 booting
init frontpanel
Mount /dev in tmpfs
Copying device nodes to /dev
Starting portmap daemon...Segmentation fault
failed!
Loading autofs
Starting autofs
Mounting local filesystems...
mount: mounting LABEL=RECORD on /hdd failed: No such file or directory
Cleaning /tmp.
Hostname: IPBOX9000.
init stmfb
offset key len data
found key tvmode ->value 4
1080I-50
LOADING MODULES
load firmware
cannot open /dev/st231-1 device (errno = 28)
cannot open /dev/st231-0 device (errno = 28)
init embx
Meine IPBox 9000 hängt beim Laden des HDMU Image (HDMU_11684_E2_ipbox9000_211_git_5569_nodebug_mix_ USB.tar.gz)
Im Flash ist PGI 1.5 , hat jemand eine Idee wass ich machen kann, hatte bis jetzt nur Flash Images von PGI.
Danke im voraus
U-Boot 1.3.1-gbbd37f59 (Aug 14 2010 - 15:29:47) - stm23-2008-03-19
Board: cuberevo (0x2D42C041)
Board: 13 grid vfd front
DRAM: 128 MB
Flash: 32 MB
In: serial
Out: serial
Err: serial
Reserve 0x2010000 bytes from 0xa5ff0000 for DGS upgrade buffer.
Saving Environment to Flash...
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
Protected 1 sectors
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
1716071 bytes read
## Booting image at a5ff0000 ...
Image Name: Linux-2.6.32.59_stm24_0211
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1716007 Bytes = 1.6 MB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Warning: Unable to determine if kernel is built for 29- or 32-bit mode!
Starting kernel console=ttyAS1,115200 panic=3 root=/dev/sdb2 rw rootdelay=10 bigphysarea=1500 quiet - 0x00000000 - 0 ...
INIT: version 2.86 booting
init frontpanel
Mount /dev in tmpfs
Copying device nodes to /dev
Starting portmap daemon...Segmentation fault
failed!
Loading autofs
Starting autofs
Mounting local filesystems...
mount: mounting LABEL=RECORD on /hdd failed: No such file or directory
Cleaning /tmp.
Hostname: IPBOX9000.
init stmfb
offset key len data
found key tvmode ->value 4
1080I-50
LOADING MODULES
load firmware
cannot open /dev/st231-1 device (errno = 28)
cannot open /dev/st231-0 device (errno = 28)
init embx