Archiv verlassen und diese Seite im Standarddesign anzeigen : Hdmu and ipbox9000
Hi everybody,
I've an ipbox9000 and i would like to try a hdmu image.
Actually I've installed a AAF E2 on flash.
Is there any step by step tutorial or can someone guide me how to get hdmu on my box?
Thanks.
Do you have a HDD in your Box?
If yes, empty or Full?
Please Login with Telnet:
fdisk -l
No, no. No hard disk installed. But maybe i can find one if is necessary.
our image must be installed on a usb stick or internal sata hdd.
internal hdd is faster then a stick.
Then i will install a hdd.
What's the first step after hdd is installed?
you have to create some partitions.
1 RECORD in ext3
2 SWAP
3 MINI1 in ext2
4 MINI2 in ext2
swap and minis should be 500MB, the other GBs for RECORD
do you know how to create parts?
Half tera for every partition? Is not to much? A black hole image for vu+ is less than 200mb. Can't believe it!
So recommended pen or hdd is 2Tb?
normal you need only 60-80MB for our image,
also 500MB per part, not 500GB
Aaah ok! Sorry for missunderstanding.
I have no idea what kind of hard drive may I install, I mean, any restrictions? What's the maximum size my box can handle? Minimum 2gb, right?
i don´t think that you have a sata hdd with 2gb, ide is not supported.
I run the image off a pen drive without too many issues!
If you have multi boot all is good...
This is how I created my pen drive boot.
I assume you have e2 in flash
You will need to be able to FTP your box, and use putty...
I use putty for the next bit.
User: root
Password: HDMU
To create a partition on the pen drive
mkfs,ext2 /dev/sdb1 -L ext2
Then copy your downloaded file into this directory via FTP transfer (tar.gz on this site)
Back to putty...to unpack the file
mount dev sdb1 /mnt/usb
Then use putty to unpack the file...
cd /mnt/usb
tar -vzxf *****.tar.gz (then the full name of the image)
then...
sync
remove the image using FTP if required.
Start your box using the correct key number on the remote. Set-up the image as per the instructions
Cheers
sata is min 20secs faster than usb, if he had a hdd, he should use it
Thanks for your help.
Which putty commands I need to do it on the hard drive?
maybe you can understand this faq-->klick (http://www.hdmedia-universe.com/board/showthread.php?1044-Partinionieren-von-HDD-und-USB-Sticks&p=12845&viewfull=1#post12845)
if not, aks again.
try to install with morlys stb admin tool-->klick (http://www.hdmedia-universe.com/board/showthread.php?4338-SH4-STB-Admin-Tool-Morly-1-4)
I can't understand German.
I've installed a 320gb sata.
From box menu I've choosed initialization and ext2 format, other options are ext3, fat32 and jfs. Ext2 is good or better chose another?
you have to create some partitions.
1 RECORD in ext3
2 SWAP
3 MINI1 in ext2
4 MINI2 in ext2
swap and minis should be 500MB, the other GBs for RECORD
do you know how to create parts?
I don't know how to create partition. I'm familiar with putty and winscp.
Can you pass me commands to make parts?
After formating from the box menu, I can not see any more the option hard disk on the menu.
from putty I can see this:
is my hdd recogniced?
root@S400:~# fdisk -l
Disk /dev/sda: 524 MB, 524869632 bytes
189 heads, 61 sectors/track, 88 cylinders, total 1025136 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x000a5053
Device Boot Start End Blocks Id System
/dev/sda1 * 2048 1023999 510976 83 Linux
Disk /dev/sdb: 4041 MB, 4041211904 bytes
64 heads, 32 sectors/track, 3854 cylinders, total 7892992 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x30624145
Device Boot Start End Blocks Id System
/dev/sdb1 * 64 1327103 663520 17 Hidden HPFS/NTFS
/dev/sdb2 1329150 7890943 3280897 5 Extended
/dev/sdb5 1329152 7516159 3093504 83 Linux
/dev/sdb6 7518208 7890943 186368 82 Linux swap / Solaris
strange, i only see two sticks, i think:
Disk /dev/sda: 524 MB,
Disk /dev/sdb: 4041 MB,
try a reboot
Yes, extrange... I saw the same. I did a soft reset, I'll try a hard reset.
No usb attached.
Maybe i can format from putty?
yes of course, but we must have to see the hdd with fdisk before
fdisk -l
we have to see 320gb, then we can create partitions with fdisk, after that format that parts with mkfs.
http://img.tapatalk.com/d/14/02/13/pe3unehe.jpg
After a hard reset the menu shows back the hard disk menu, showing correct size of the hdd. If i try to inicializate always say error mounting. Fdisk -l doesn't show real size.
I Will try another hard disk or will try with a pen drive.
Put the HDD in a pc and format with any Tool.
After that try again in Box.
My pc is a laptop without sata ports.
On Morlys utility, where should I copy dll files for windows 7?
identical results with another hdd:
root@S400:~# fdisk -l
Disk /dev/sda: 524 MB, 524869632 bytes
189 heads, 61 sectors/track, 88 cylinders, total 1025136 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x000a5053
Device Boot Start End Blocks Id System
/dev/sda1 * 2048 1023999 510976 83 Linux
Disk /dev/sdb: 4041 MB, 4041211904 bytes
64 heads, 32 sectors/track, 3854 cylinders, total 7892992 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x30624145
Device Boot Start End Blocks Id System
/dev/sdb1 * 64 1327103 663520 17 Hidden HPFS/NTFS
/dev/sdb2 1329150 7890943 3280897 5 Extended
/dev/sdb5 1329152 7516159 3093504 83 Linux
/dev/sdb6 7518208 7890943 186368 82 Linux swap / Solaris
root@S400:~#
- - - Aktualisiert - - -
I run the image off a pen drive without too many issues!
If you have multi boot all is good...
This is how I created my pen drive boot.
I assume you have e2 in flash
You will need to be able to FTP your box, and use putty...
I use putty for the next bit.
User: root
Password: HDMU
To create a partition on the pen drive
mkfs,ext2 /dev/sdb1 -L ext2
Then copy your downloaded file into this directory via FTP transfer (tar.gz on this site)
Back to putty...to unpack the file
mount dev sdb1 /mnt/usb
Then use putty to unpack the file...
cd /mnt/usb
tar -vzxf *****.tar.gz (then the full name of the image)
then...
sync
remove the image using FTP if required.
Start your box using the correct key number on the remote. Set-up the image as per the instructions
Cheers
When I put the first comand I get this:
root@S400:~# mkfs,ext2 /dev/sdb1 -L ext2
-bash: mkfs,ext2: no se encontró la orden (command not found)
the command is wrong, it should be mkfs.ext2 /dev...
Remove your hdd, put a usb stick on your Box and boot.
then show me fdisk -l
Hdd removed, atached 4Gb usb stick, power on box, fdisk:
root@S400:~# fdisk -l
Disk /dev/sda: 524 MB, 524869632 bytes
189 heads, 61 sectors/track, 88 cylinders, total 1025136 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x000a5053
Device Boot Start End Blocks Id System
/dev/sda1 * 2048 1023999 510976 83 Linux
Disk /dev/sdb: 4041 MB, 4041211904 bytes
64 heads, 32 sectors/track, 3854 cylinders, total 7892992 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x30624145
Device Boot Start End Blocks Id System
/dev/sdb1 * 64 1327103 663520 17 Hidden HPFS/NTFS
/dev/sdb2 1329150 7890943 3280897 5 Extended
/dev/sdb5 1329152 7516159 3093504 83 Linux
/dev/sdb6 7518208 7890943 186368 82 Linux swap / Solaris
root@S400:~#
- - - Aktualisiert - - -
root@S400:~# mkfs.ext2 /dev/sdb1 -L ext2
mke2fs 1.42.5 (29-Jul-2012)
Etiqueta del sistema de ficheros=ext2
OS type: Linux
Tamaño del bloque=4096 (bitácora=2)
Tamaño del fragmento=4096 (bitácora=2)
Stride=0 blocks, Stripe width=0 blocks
41472 inodes, 165880 blocks
8294 blocks (5.00%) reserved for the super user
Primer bloque de datos=0
Número máximo de bloques del sistema de ficheros=171966464
6 bloque de grupos
32768 bloques por grupo, 32768 fragmentos por grupo
6912 nodos-i por grupo
Respaldo del superbloque guardado en los bloques:
32768, 98304, 163840
Allocating group tables: hecho
Escribiendo las tablas de nodos-i: hecho
Escribiendo superbloques y la información contable del sistema de ficheros: hecho
If you need spanish to english translation let me now.
Then Ray said:
Then copy your downloaded file into this directory via FTP transfer (tar.gz on this site)witch destination directory should it go tar.gz file?
root@S400:~# blkid
/dev/sdb6: UUID="a26b6819-829f-49a7-a6d0-b7e35ec5c4f1" TYPE="swap"
/dev/sda1: UUID="523e3d3e-8e8b-4c0e-bcf6-8ce0207d26be" TYPE="ext4"
/dev/sdb1: LABEL="ext2" UUID="41f5e7ac-c7ce-4459-be62-a9600e59ad6a" TYPE="ext2"
/dev/sdb5: UUID="1c449d43-6205-4d6f-91fa-095de646405a" TYPE="ext4"
root@S400:~# mount
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,relatime)
udev on /dev type devtmpfs (rw,relatime,size=10240k,nr_inodes=58978,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode =000)
tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=48188k,mode=755)
/dev/disk/by-uuid/1c449d43-6205-4d6f-91fa-095de646405a on / type ext4 (rw,relatime,errors=remount-ro,user_xattr,barrier=1,data=ordered)
tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k)
tmpfs on /run/shm type tmpfs (rw,nosuid,nodev,noexec,relatime,size=133640k)
rpc_pipefs on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw,relatime)
fdisk /dev/sdb
d (delete all parts)
6
d
5
d
2
d
1
n (create new part)
p (primary)
1 (first part)
1 or return
xxx (=max cylinder/4)
n
p
2
return
yyy
n
p
3
return
zzz
n
p
4
return
return
w
reboot
fdisk -l
Oh my god! I've made a little big disaster! All the time I was pointing to a wrong IP where is one of my servers, its a mini pc and the boot was on usb stick, so now after repartition of usb stick the server doesn't boot anymore. Thats why fdisk wasn't showing correct size.
Now i have to fix pc boot. I'll continue with ipbox later.
Very sorry for time wasting!
Hi Santa, I've fixed my server.
Can we start again? this time from hard disk.
AAF-ipbox9000:~# fdisk -l
Disk /dev/sda: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 38913 312568641 1 FAT12
Now the Same like post #30, only delete Part 1.
And you have to open fdisk with /dev/sda
When I create first primary part;
xxx (=max cylinder/4)
What should i put instead xxx?
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-38913, default 1): 1
Last cylinder or +size or +sizeM or +sizeK (1-38913, default 38913): xxx
Last cylinder or +size or +sizeM or +sizeK (1-38913, default 38913): 38913
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 2
No free sectors available
delete
n
p
1
1
38750
n
p
2
return
38800
n
p
3
return
38850
n
p
4
return
return
w
mkswap -L SWAPPART /dev/sda2
mkfs.ext2 -I128 -b4096 -L MINI3 /dev/sda3
mkfs.ext2 -I128 -b4096 -L MINI4 /dev/sda4
mkfs.ext4 -L RECORD /dev/sda1
the last comand could make problems, but then we format this part later, pleas post
all what you have done.
As you said, last command failed, I think everything else is fine.
* * * * * * * * * * * * * * * * * * * * * * * * * * *
* __ __ __________ *
* / \ / \ | ________) *
* / __ \ / __ \ | | *
* / / \ \ / / \ \ | |_____ *
* / /____\ \ / /____\ \ | _____) *
* / /______\ \ / /______\ \ | | *
* / / \ \ / / \ \ | | *
* (__) (__) (__) (__) (___) *
* *
* * * * * * * * * * * * * * * * * * * * * * * * * * *
>> wElc0me to AAF Don't Cry Image (Image 38)
>> AAF_M15000_rev_3650_ipbox9000_enigma2
* * * * * * * * * * * * * * * * * * * * * * * * * * *
BusyBox v1.19.2 (2011-10-03 06:39:15 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
AAF-ipbox9000:~# fdisk /dev/sda
The number of cylinders for this disk is set to 38913.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): d
Selected partition 1
Command (m for help): 1
1: unknown command
Command Action
a toggle a bootable flag
b edit bsd disklabel
c toggle the dos compatibility flag
d delete a partition
l list known partition types
n add a new partition
o create a new empty DOS partition table
p print the partition table
q quit without saving changes
s create a new empty Sun disklabel
t change a partition's system id
u change display/entry units
v verify the partition table
w write table to disk and exit
Command (m for help): d
No partition is defined yet!
Command (m for help):
AAF-ipbox9000:~# fdisk /dev/sda
The number of cylinders for this disk is set to 38913.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): d
Selected partition 1
Command (m for help): 1
1: unknown command
Command Action
a toggle a bootable flag
b edit bsd disklabel
c toggle the dos compatibility flag
d delete a partition
l list known partition types
n add a new partition
o create a new empty DOS partition table
p print the partition table
q quit without saving changes
s create a new empty Sun disklabel
t change a partition's system id
u change display/entry units
v verify the partition table
w write table to disk and exit
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-38913, default 1): 1
Last cylinder or +size or +sizeM or +sizeK (1-38913, default 38 913): 38750
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 2
First cylinder (38751-38913, default 38751): Using default valu e 38751
Last cylinder or +size or +sizeM or +sizeK (38751-38913, defaul t 38913): 38800
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 3
First cylinder (38801-38913, default 38801): Using default valu e 38801
Last cylinder or +size or +sizeM or +sizeK (38801-38913, defaul t 38913): 38850
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Selected partition 4
First cylinder (38851-38913, default 38851): Using default valu e 38851
Last cylinder or +size or +sizeM or +sizeK (38851-38913, defaul t 38913): Using default value 38913
Command (m for help): w
The partition table has been altered.
Calling ioctl() to re-read partition table
AAF-ipbox9000:~# mkswap -L SWAPPART /dev/sda2
Setting up swapspace version 1, size = 411259904 bytes
UUID=5f374766-406c-4580-b72e-b16053968c0a
AAF-ipbox9000:~# mkfs.ext2 -I128 -b4096 -L MINI3 /dev/sda3
[mkfs.info] start (-I128 -b4096 -L MINI3 /dev/sda3)
*** InfoBox v1.7 by GOst4711 and nit ***
1920x1080, 32bpp
mke2fs 1.41.14 (22-Dec-2010)
------- Programmende
*** InfoBox v1.7 by GOst4711 and nit ***
1920x1080, 32bpp
Filesystem label=MINI3
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
Stride=0 blocks, Stripe width=0 blocks
100480 inodes, 100406 blocks
5020 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=104857600
4 block groups
32768 blocks per group, 32768 fragments per group
25120 inodes per group
Superblock backups stored on blocks:
32768, 98304
Writing inode tables: done
Writing superblocks and filesystem accounting information: done
This filesystem will be automatically checked every 25 mounts o r
180 days, whichever comes first. Use tune2fs -c or -i to overr ide.
------- Programmende
*** InfoBox v1.7 by GOst4711 and nit ***
AAF-ipbox9000:~# 1920x1080, 32bpp
------- Programmende
AAF-ipbox9000:~# mkfs.ext2 -I128 -b4096 -L MINI4 /dev/sda4
[mkfs.info] start (-I128 -b4096 -L MINI4 /dev/sda4)
*** InfoBox v1.7 by GOst4711 and nit ***
1920x1080, 32bpp
mke2fs 1.41.14 (22-Dec-2010)
------- Programmende
*** InfoBox v1.7 by GOst4711 and nit ***
1920x1080, 32bpp
Filesystem label=MINI4
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
Stride=0 blocks, Stripe width=0 blocks
126592 inodes, 126511 blocks
6325 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=130023424
4 block groups
32768 blocks per group, 32768 fragments per group
31648 inodes per group
Superblock backups stored on blocks:
32768, 98304
Writing inode tables: done
Writing superblocks and filesystem accounting information: done
This filesystem will be automatically checked every 27 mounts o r
180 days, whichever comes first. Use tune2fs -c or -i to overr ide.
------- Programmende
AAF-ipbox9000:~# *** InfoBox v1.7 by GOst4711 and nit ***
1920x1080, 32bpp
------- Programmende
AAF-ipbox9000:~# mkfs.ext4 -L RECORD /dev/sda1
-sh: mkfs.ext4: not found
AAF-ipbox9000:~# fdisk -l
Disk /dev/sda: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 38750 311259343+ 83 Linux
/dev/sda2 38751 38800 401625 83 Linux
/dev/sda3 38801 38850 401625 83 Linux
/dev/sda4 38851 38913 506047+ 83 Linux
AAF-ipbox9000:~#
ok, reboot.
i need this:
fw_printenv
AAF-ipbox9000:~# fw_printenv
baudrate=115200
preboot=if edb toenv ethaddr; then echo "Setup mac address."; else echo "Use def ault mac address."; fi; bootmenu
menu_timeout=echo booting...;front_puts "booting";boot
menu_serialbreak=echo entering boot loader console.;front_puts "console"
menu_upgusb=setenv stdout vga;setenv stderr vga;if usbupg; then reset; else echo Oops...; echo You can debug through serial port.; fi
menu_upgusbhost=setenv stdout vga;setenv stderr vga;if usbupghost; then reset; e lse echo Oops...; echo You can debug through serial port.; fi
menu_upgserial=setenv stdout vga;setenv stderr vga;serial_upgrade;reset
menu_set2set=setenv stdout vga;setenv stderr vga;serial_set2set;reset
menu_hddfmt=setenv bootargs $bootargs format_hdd=1;front_puts "format hdd";boot
menu_debugmode=setenv bootargs $bootargs debug debug_app=1;front_puts "debug she ll";boot
menu_upgnet=setenv bootargs "console=ttyAS1,115200 panic=3 root=/dev/mtdblock3 q uiet" factory_update=1;front_puts "net upg";boot
menu_tvmode=set_tvmode;boot
serial#=cuberevo-mini2 debugging
board=cuberevo-mini2_27
monitor_base=0xA0000000
monitor_len=0x00040000
monitor_sec=1:0
load_addr=0x84000000
unprot=protect off $monitor_sec
update=erase $monitor_sec;cp.b $load_addr $monitor_base $monitor_len;protect on $monitor_sec
ipaddr=192.168.178.1
gateway=192.168.178.254
netmask=255.255.255.0
serverip=192.168.178.254
menu_1=setenv bootargs "console=ttyAS1,115200 root=/dev/mtdblock3 mem=128m ip=$i paddr:$serverip:$gateway:$netmask:cuberevo:eth0:of f coprocessor_mem=4m@0x1000000 0,4m@0x10400000 rootdelay=0 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "bootm a0060000";saveenv;front_puts FLASH;boot
menu_2=setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/ uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda1 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cube revo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 n whwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_ puts SDA1-USB;boot
menu_3=setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:2 a5ff0000 boot/ uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda2 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cube revo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 n whwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_ puts SDA2-USB;boot
menu_4=setenv bootide "run bootargside;ide reset;ext2load ide 0:1 a5ff0000 boot/ uImage;bootm a5ff0000";setenv bootargside "setenv bootargs console=ttyAS1,115200 root=/dev/sda3 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cube revo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 n whwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootide";saveenv;front_ puts SDA3-IDE;boot
menu_5=setenv bootide "run bootargside;ide reset;ext2load ide 0:2 a5ff0000 boot/ uImage;bootm a5ff0000";setenv bootargside "setenv bootargs console=ttyAS1,115200 root=/dev/sda4 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cube revo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 n whwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootide";saveenv;front_ puts SDA4-IDE;boot
menu_6=setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/ uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sdb1 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cube revo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 n whwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_ puts SDB1-USB;boot
menu_7=setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:2 a5ff0000 boot/ uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sdb2 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cube revo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 n whwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_ puts SDB2-USB;boot
menu_8=setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:3 a5ff0000 boot/ uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sdb3 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cube revo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 n whwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_ puts SDB3-USB;boot
menu_9=setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:4 a5ff0000 boot/ uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sdb4 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cube revo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 n whwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_ puts SDB4-USB;boot
menu_0=setenv ipaddr 192.168.1.10;setenv serverip 192.168.1.9;setenv gateway 192 .168.1.1;setenv netmask 255.255.255.0;setenv bootargs "console=ttyAS1,115200 roo t=/dev/nfs nfsroot=/mnt/nfs/enigma/ron rw rootpath=/mnt/nfs/enigma/ron ip=$ipadd r:$serverip:$gateway:$netmask:cuberevo:eth0:off mem=128m coprocessor_mem=4m@0x10 000000,4m@0x10400000 init=/bin/devinit nwhwconf=device:eth0,hwaddr:$ethaddr";set env bootcmd "nfs a5ff0000 192.168.1.9:/mnt/nfs/enigma/ron/boot/uImage;bootm a5ff 0000";saveenv;front_puts NFS;boot
bootusb=run bootargsusb;usb reset;ext2load usb 0:2 a5ff0000 boot/uImage;bootm a5 ff0000
bootargsusb=setenv bootargs console=ttyAS1,115200 root=/dev/sda2 rw init=/bin/de vinit ip=192.168.178.1:192.168.178.254:192.168.178.254:2 55.255.255.0:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf =device:eth0,hwaddr:00:13:18:02:40:14
stdin=serial
stdout=serial
stderr=serial
ethaddr=00:13:18:02:40:14
bootargs=console=ttyAS1,115200 root=/dev/mtdblock3 mem=128m ip=192.168.178.1:192 .168.178.254:192.168.178.254:255.255.255.0:cuberev o:eth0:off coprocessor_mem=4m@ 0x10000000,4m@0x10400000 rootdelay=0 nwhwconf=device:eth0,hwaddr:00:13:18:02:40: 14
bootcmd=bootm a0060000
fw_setenv menu_3 'setenv bootide "run bootargside;ide reset;ext2load ide 0:3 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargside "setenv bootargs console=ttyAS1,115200 root=/dev/sda3 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=0 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootide";saveenv;front_puts SDA3-IDE;boot'
fw_setenv menu_4 'setenv bootide "run bootargside;ide reset;ext2load ide 0:4 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargside "setenv bootargs console=ttyAS1,115200 root=/dev/sda4 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:et h0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=0 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootide";saveenv;front_puts SDA4-IDE;boot'
cd /autofs/sda3
if this is possible, open ftp and copy image to /autofs/sda3
after that, telnet again:
tar xvzf *.tar.gz
Ok, copied and unziped.
What next? we are close yes? :)
shutdown
key power, then hold key number 3 until ide-sda3 is to read in your vfd.
now hdmu should boot.
configure your image, then:
mkfs.ext4 -L RECORD /dev/sda1
reboot, have fun
Ok Santa, we'll do the final step tomorror.
Thanks alot!
Tomorrow I'll post results.
Are you sure is number 3 on the remote control?
I've found this:
1) boot from cdkroot
2) boot from USB with hdd
3) original images
4) boot from release
5) boot from USB without hdd
6) boot from SATA hdd
7) boot from flash
Yes, because fw_setenv sets New bootsrgs, and we prepare key 3 and 4
http://img.tapatalk.com/d/14/02/18/ubana2u8.jpg
Sda2-usb and nothing on tv screen.
If i hold on number 4 on tv control, vfd shows sda3-IDE but doesn't boot and black screen on tv.
You have to use fw_setenv like in post 39 before you can Boot from that.
I don't understand what i must do with all that data (fw_setenv...) should i put it with putty? Everything?
- - - Aktualisiert - - -
Is this way?
AAF-ipbox9000:~# fw_setenv menu_3 'setenv bootide "run bootargside;ide reset;ext
2load ide 0:3 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargside "setenv bo
otargs console=ttyAS1,115200 root=/dev/sda3 rw init=/bin/devinit ip=$ipaddr:$ser
verip:$gateway:$netmask:cuberevo:eth0:off mem=128m coprocessor_mem=4m@0x10000000
,4m@0x10400000 rootdelay=0 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd
"run bootide";saveenv;front_puts SDA3-IDE;boot'
Unlocking flash...
Done
Erasing old environment...
Done
Writing environment to /dev/mtd1...
Done
Locking ...
Done
AAF-ipbox9000:~#
AAF-ipbox9000:~#
AAF-ipbox9000:~# fw_setenv menu_4 'setenv bootide "run bootargside;ide reset;ext2load ide 0:4 a5ff0000 boot/uImage;bootm a5ff0000";set
env bootargside "setenv bootargs console=ttyAS1,115200 root=/dev/sda4 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cube
revo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=0 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "r
un bootide";saveenv;front_puts SDA4-IDE;boot'
Unlocking flash...
Done
Erasing old environment...
Done
Writing environment to /dev/mtd1...
Done
Locking ...
Done
- - - Aktualisiert - - -
Done! finaly! its working!
You've been so kind! thank you so much!
Which softcam do you recomend for cccam connection as a client?
Sorry we don't Support sharing.
It's my own server, i share with myself. Anyway, I respect your rules.
Thanx again.
Powered by vBulletin® Version 4.2.5 Copyright ©2024 Adduco Digital e.K. und vBulletin Solutions, Inc. Alle Rechte vorbehalten.