HDMU_12069_E2_spark_212_git_5616_nodebug_mix_Flash

[rangerm]

Weil ihr so schön jammert das keiner Testet hier mal paar Worte zum Image ;)

Hab das Image seit 3 Tagen drauf, und ja einen Fehler hab ich gefunden was aber wahrscheinlich den meisten sowieso nicht auffällt.

Nämlich wenn man über die Nummern Tasten umschaltet, werden keinen Zahlen am TV angezeigt es kommt das Kästchen ist aber leer.

Sonst sind die Umschaltzeiten wieder schneller aber richtige Fehler Sorry find ich nicht.

ps. wenn hier mehr Feedback wollt müsst ihr auch mal Fehler einbauen :D

[bonkel]

Default Skin?

[rangerm]

jo Default skin

[bonkel]

mh , grad mal auf der triple getestet, hab da zahlen

[balkanac82]

So jetzt. War noch am essen. Hier der logg zum Zapp problem bei mir. Wie gesagt wen ich Umschalte zeigt sich der Spinner und das umschalten dauert dan.

Log

#Log file from Morlys SH4 STB Admin Tool from: Do Mrz 13 2014, 21:22:03

not enough diskspace for timeshift! (less than 200MB)
playing 1:0:19:2B66:3F3:1:C00000:0:0:0:
[eDVBCAService] free slot 0 demux 0 for service 1:0:19:283D:3FB:1:C00000:0:0:0:
[eDVBCAService] free service 1:0:19:283D:3FB:1:C00000:0:0:0:
decoder state: play, vpid=-1, apid=-1
DEMUX_STOP - pcr - ok
DEMUX_STOP - video - ok
VIDEO_STOP - ok
AUDIO_STOP - ok
DEMUX_STOP - audio - ok
AUDIO_CONTINUE - ok
DEMUX_STOP - ttx - ok
TuxTxt stopped service 13f0
cleaning up
TuxTxt cache cleared
start release channel timer
[__evStart]
[__evSeekableStatusChanged]
not enough diskspace for timeshift! (less than 200MB)
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
RemovePopup, id = ZapError
[eDVBLocalTimerHandler] remove channel 0x2d33a428
[eEPGCache] remove channel 0x2d33a428
allocate channel.. 03f3:0001
(0)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 1 Freq 11361750 Pol 0 SR 22000000 INV 2 FEC 2 orbpos 192 system 1 modulation 2 pilot 2, rolloff 0
tuning to 1611 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:19:2B66:3F3:1:C00000:0:0:0:
allocate demux
set sequence pos 3
set sequence pos 3
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 0
(0)fe event: status 0, inversion off, m_tuning 1
(0)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x1b07708 running
[eEPGCache] channel 0x1b07708 running
[EPGC] next update in 2 sec
stop release channel timer
eventNewProgramInfo 0 0
have 1 video stream(s) (17de), and 1 audio stream(s) (17e8), and the pcr pid is 17de, and the text pid is 17f2
allocate demux
TuxTxt cache cleared
decoder state: play, vpid=6110, apid=6120
DMX_SET_PES_FILTER(0x17de) - pcr - ok
DMX_SET_PES_FILTER(0x17e8) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 1 - ok
DMX_SET_PES_FILTER(0x17de) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x17f2) - ttx - ok
TuxTxt cache cleared
TuxTxt: initialized
TuxTxt service started 17f2
VIDEO_CONTINUE - ok
VIDEO_SLOWMOTION(0) - TuxTxt running thread...(17f2)
ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
disable teletext subtitles page ffffffffffffffff (und)
[AutomaticVolumeAdjustment] service changed
[__evUpdatedInfo]
[writeChannelName]
vfd display text: ZDF HD
[showCrypted]
[showDolby]
[showMp3]
FE_GET_PROPERTY failed (Invalid argument)
[eDVBCAService] new service 1:0:19:2B66:3F3:1:C00000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:19:2B66:3F3:1:C00000:0:0:0:
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
[EPGC] start caching events(1394742077)
main thread is non-idle! display spinner!
[__evUpdatedEventInfo]
RemovePopup, id = ZapError
[SEC] sleep 500ms
[eDVBLocalTimerHandler] diff is 1
[eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
[eDVBLocalTimerHandler] update RTC
[eDVBLocalTimerHandler] time update to 21:21:23
[eDVBLocalTimerHandler] m_time_difference is 1
[eDVBLocalTimerHandler] set Linux Time
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 5
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
ERROR reading PES (fd=51) - Value too large for defined data type
poll: unhandled POLLERR/HUP/NVAL for fd 51(8)
use pmtpid 17d4 for service_id 2b66
[Dish] tuning failed
sdt update done!
eventNewProgramInfo 0 0
dvb subtitle PID 17f3 with wrong subtitling type (24)... force 0x10!!
have 1 video stream(s) (17de), and 4 audio stream(s) (17e8, 17e9, 17eb, 17ea), and the pcr pid is 17de, and the text pid is 17f2
decoder state: play, vpid=6110, apid=6120
dvb subtitle PID 17f3 with wrong subtitling type (24)... force 0x10!!
[__evUpdatedInfo]
[writeChannelName]
vfd display text: ZDF HD
[showCrypted]
[showDolby]
[showMp3]
FE_GET_PROPERTY failed (Invalid argument)
[__evUpdatedEventInfo]
[EPGC] abort non avail schedule other reading
[EPGC] abort non avail netmed schedule reading
[EPGC] abort non avail netmed schedule other reading
[EPGC] abort non avail FreeSat schedule_other reading
[EPGC] abort non avail viasat reading
ERROR reading PES (fd=51) - Value too large for defined data type
poll: unhandled POLLERR/HUP/NVAL for fd 51(8)
[EPGC] nownext finished(1394742086)
[__evUpdatedInfo]
[writeChannelName]
vfd display text: ZDF HD
[showCrypted]
[showDolby]
[showMp3]
not enough diskspace for timeshift! (less than 200MB)
playing 1:0:19:283F:3FB:1:C00000:0:0:0:
[eDVBCAService] free slot 0 demux 0 for service 1:0:19:2B66:3F3:1:C00000:0:0:0:
[eDVBCAService] free service 1:0:19:2B66:3F3:1:C00000:0:0:0:
decoder state: play, vpid=-1, apid=-1
DEMUX_STOP - pcr - ok
DEMUX_STOP - video - ok
VIDEO_STOP - ok
AUDIO_STOP - ok
DEMUX_STOP - audio - ok
AUDIO_CONTINUE - ok
DEMUX_STOP - ttx - ok
TuxTxt stopped service 17f2
cleaning up
TuxTxt cache cleared
start release channel timer
[__evStart]
[__evSeekableStatusChanged]
not enough diskspace for timeshift! (less than 200MB)
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
RemovePopup, id = ZapError
[eDVBLocalTimerHandler] remove channel 0x1b07708
[eEPGCache] remove channel 0x1b07708
[EPGC] abort caching events !!
allocate channel.. 03fb:0001
(0)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 1 Freq 11493750 Pol 0 SR 22000000 INV 2 FEC 2 orbpos 192 system 1 modulation 2 pilot 2, rolloff 0
tuning to 1743 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:19:283F:3FB:1:C00000:0:0:0:
allocate demux
set sequence pos 3
set sequence pos 3
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 0
(0)fe event: status 0, inversion off, m_tuning 1
(0)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x1da6c10 running
[eEPGCache] channel 0x1da6c10 running
[EPGC] next update in 57 min
stop release channel timer
eventNewProgramInfo 0 0
have 1 video stream(s) (1401), and 1 audio stream(s) (1402), and the pcr pid is 1401, and the text pid is 1404
allocate demux
TuxTxt cache cleared
decoder state: play, vpid=5121, apid=5122
DMX_SET_PES_FILTER(0x1401) - pcr - ok
DMX_SET_PES_FILTER(0x1402) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 1 - ok
DMX_SET_PES_FILTER(0x1401) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x1404) - ttx - ok
TuxTxt cache cleared
TuxTxt: initialized
TuxTxt service started 1404
VIDEO_CONTINUE - ok
VIDEO_SLOWMOTION(0) - TuxTxt running thread...(1404)
ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
disable teletext subtitles page ffffffffffffffff (und)
[AutomaticVolumeAdjustment] service changed
[__evUpdatedInfo]
[writeChannelName]
vfd display text: SWR BW HD
[showCrypted]
[showDolby]
[showMp3]
FE_GET_PROPERTY failed (Invalid argument)
[eDVBCAService] new service 1:0:19:283F:3FB:1:C00000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:19:283F:3FB:1:C00000:0:0:0:
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
main thread is non-idle! display spinner!
[__evUpdatedEventInfo]
RemovePopup, id = ZapError
[SEC] sleep 500ms
[eDVBLocalTimerHandler] diff is -2
[eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
[eDVBLocalTimerHandler] update RTC
[eDVBLocalTimerHandler] time update to 21:21:37
[eDVBLocalTimerHandler] m_time_difference is -2
[eDVBLocalTimerHandler] set Linux Time
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 5
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
ERROR reading PES (fd=51) - Value too large for defined data type
poll: unhandled POLLERR/HUP/NVAL for fd 51(8)
use pmtpid 1400 for service_id 283f
[Dish] tuning failed
sdt update done!
eventNewProgramInfo 0 0
dvb subtitle PID 1405 with wrong subtitling type (24)... force 0x10!!
have 1 video stream(s) (1401), and 3 audio stream(s) (1402, 1403, 1406), and the pcr pid is 1401, and the text pid is 1404
decoder state: play, vpid=5121, apid=5122
dvb subtitle PID 1405 with wrong subtitling type (24)... force 0x10!!
[__evUpdatedInfo]
[writeChannelName]
vfd display text: SWR BW HD
[showCrypted]
[showDolby]
[showMp3]
FE_GET_PROPERTY failed (Invalid argument)
[__evUpdatedInfo]
[writeChannelName]
vfd display text: SWR BW HD
[showCrypted]
[showDolby]
[showMp3]
[__evUpdatedEventInfo]
ERROR reading PES (fd=51) - Value too large for defined data type
poll: unhandled POLLERR/HUP/NVAL for fd 51(8)

[bonkel]

mh hast du ne Festplatte dran? mach mal ein fsck also fehlerprüfung

[rangerm]

Würde es dir gerne logen aber Weibchen meckert schon wieder :D

Aber bevor du mir nicht glaubst durfte ich schnell Foto machen.

[bonkel]

ja gut, log wäre glaub ich hilfreich, von start an
vielleicht meckert der beim start schon was.....


irgendwelche Settings oder so eingespielt? oder ein Skin installiert und wieder entfernt?

[rangerm]

@balkan

Kann des sein das du perm Timeshift auf der Box hast ?


not enough diskspace for timeshift! (less than 200MB)



@benny

Es wurde kein Skin installiert und wieder gelöscht.
Settings ja das übliche Backup wiederhergestellt wie immer Sendeliste,emu und zwei Plugins dürfte also kaum Auswirkungen haben.

Log vom start kommt so in 30 Min ;)

[balkanac82]

Ich habe keine Festplatte drauf. Hatte nur einmal einen USB Stick drinnen, um ein Full Backup vom Image zum machen für meine Zweitbox. Übrigens geht es jetzt, wen man ein Fullbackup macht, das gesicherte Image mit USB zurückzuspielen.

EDIT. Ich mach mal von Start an ein Log. Timeshift benutze ich nicht.

[rangerm]

So Werbung genutzt



LCD resolution: -1 x -1 x -1431760128 (stride: 715840928)
+ (9) Font Render Class
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "HDMU RC SPARK" is a remotecontrol
Input device "HDMU RC SPARK" is a remotecontrol
failed to open /dev/input/event2
Input device "HDMU RC SPARK" is a remotecontrol
failed to open /dev/input/event3
Input device "HDMU RC SPARK" is a remotecontrol
Found 4 input devices.
+ (22) Hdmi CEC driver
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
done, found 0 common interface slots
+ (35) CA handler
+ (36) Stream server
[SERVERSOCKET] ERROR on bind() (Address already in use)
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryDVD
+ (41) eServiceFactoryEPlayer3
+ (41) eServiceFactoryHDMI
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
---- opening lame channel db
reading services (version 4)
loaded 241 channels/transponders and 3662 services
scanning for frontends..
opening frontend 0
frontend successfully opened
close frontend 0
found 1 adapter, 1 frontends(1 sim) and 2 demux, boxtype 28
Use valid Linux Time :) (RTC?)
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
[ePNG] couldn't open /usr/local/share/enigma2/skin_default/spinner/wait13.png
found 12 spinner!

executing main
setIoPrio best-effort level 3 ok
Failed to open /dev/dbox/fp0
Scanning hardware info
Detected: spark
[Harddisk] enumerating block devices...
new Harddisk sda -> /dev/sda -> /dev/sda
main thread is non-idle! display spinner!
Reading satellites.xml
sec config cleared
setSlotInfo for dvb frontend 0 to slotid 0, descr STV090x Multistandard, need ro
torworkaround No, enabled Yes, DVB-S2 Yes
slot: 0 configmode: simple
diseqcmode: diseqc_a_b_c_d
sec config completed
[Picon] adding path: /usr/share/enigma2/picon/
3660kB available for acceleration surfaces.
resolution: 1280 x 720 x 32 (stride: 5120)
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such d
evice: '/dev/input/mouse3' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such d
evice: '/dev/input/mouse2' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such d
evice: '/dev/input/mouse1' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such d
evice: '/dev/input/mouse0' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such d
evice: '/dev/input/event3' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such d
evice: '/dev/input/event2' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 22] Invalid a
rgument >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 22] Invalid a
rgument >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such d
evice: '/dev/input/mice' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such d
evice: '/dev/input/js3' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such d
evice: '/dev/input/js2' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such d
evice: '/dev/input/js1' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such d
evice: '/dev/input/js0' >
Selected keymap does not exist!
Activating language Deutsch
[ePopen] command: ip -o addr show dev eth0
eDBoxLCD::getInstance
[eSocketMMIHandler] created successfully
getModeList for port Component
getModeList for port Scart
getModeList for port HDMI
getModeList for port HDMI-PC
hotplug on dvi
setMode - port: HDMI mode: 1080i rate: 50Hz
updateColor: HDMI
LINE # automatically generated by enigma 2
LINE
[AutoMount.py] self.automounts without mounts {}
[NetworkBrowser] fallback to default translation for NetworkBrowser
[NetworkBrowser] fallback to default translation for Search for network shares
[NetworkBrowser] fallback to default translation for MountManager
[NetworkBrowser] fallback to default translation for Manage network shares
[Autologin DynDNS] autostart
starting hotplug handler
adding Resource DiseqcTester
resources: {'DiseqcTester': <function DiseqcTesterMain at 0x1969994>}
self.input oscam9462libusb
self.input oscam8963libusb
self.input oscam8523
self.input oscam8907libusb
[Toplevel.importExternalModules] Imported external module: Example
[HTTPRootResource}.__init__
[Webinterface] started on 0.0.0.0:80 auth=False ssl=False
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[HTTPRootResource}.__init__
[Webinterface] started on 0.0.0.0:443 auth=True ssl=True
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[EPGC] setCacheFile read/write epg data from/to '/hdd/epg.dat'
[EPGC] time updated.. start EPG Mainloop
[EPGC] /hdd/epg.dat not found, try /epg.dat
[SKIN] Parsing embedded skin <embedded-in-'Screensaver'>
warning, skin is missing element boquet in <class 'Screens.ChannelSelection.Chan
nelSelection'>
fp_control: SW Version 1.03
Model: spark
vBoxType: 11
Selected Model: Edision Spark frontpanel control utility
Spark_init
checkConfig
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S
, WAKEUPDECREMENT 300
18
warning, skin is missing element RassLogo in <class 'Screens.RdsDisplay.RdsInfoD
isplay'>
[SKIN] No skin to read...
warning, skin is missing element UnhandledKeyPixmap in <class 'Screens.Unhandled
Key.UnhandledKey'>
warning, skin is missing element From in <class 'Screens.Dish.Dish'>
warning, skin is missing element Goto in <class 'Screens.Dish.Dish'>
warning, skin is missing element tunerName in <class 'Screens.Dish.Dish'>
warning, skin is missing element turnSpeed in <class 'Screens.Dish.Dish'>
warning, skin is missing element posGoto in <class 'Screens.Dish.Dish'>
warning, skin is missing element posFrom in <class 'Screens.Dish.Dish'>
warning, skin is missing element turnTime in <class 'Screens.Dish.Dish'>
RemovePopup, id = ZapError
setValue 20
Setvolume: 20 20 (raw)
Setvolume: 51 51 (-1db)
playing 1:0:1:2F3A:441:1:C00000:0:0:0:
[__evStart]
[__evSeekableStatusChanged]
not pauseable.
not pauseable.
not pauseable.
RemovePopup, id = ZapError
allocate channel.. 0441:0001
opening frontend 0
frontend successfully opened
(0)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 0 Freq 12187500 Pol 0 SR 27500000 INV 2 FEC 3 orbpos 192 syst
em 0 modulation 1 pilot 2, rolloff 0
tuning to 1587 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:1:2F3A:441:1:C00000:0:0:0:
allocate demux
cidr invalid: 64
[ePopen] command: route -n | grep eth0
poll: unhandled POLLERR/HUP/NVAL for fd 29(16)
Timeout!
192.168
0.0.0.0
nameservers: [[192, 168, 2, 1]]
read configured interface: {'lo': {'dhcp': False}, 'eth0': {'dhcp': True}}
self.ifaces after loading: {'eth0': {'preup': False, 'predown': False, 'ip': [19
2, 168, 2, 122], 'up': True, 'mac': '24:00:08:00:39:6c', 'dhcp': True, 'bcast':
[192, 168, 2, 255], 'netmask': [255, 255, 255, 0], 'gateway': [192, 168, 2, 1]}}
poll: unhandled POLLERR/HUP/NVAL for fd 37(16)
set sequence pos 3
set sequence pos 4
[SEC] setVoltage 1
[SEC] sleep 200ms
[SEC] invalidate current switch params
[SEC] sendDiseqc: e00000(DiSEqC reset)
[SEC] sleep 50ms
[SEC] sendDiseqc: e00003(DiSEqC peripherial power on)
[SEC] sleep 150ms
[SEC] sendDiseqc: e01038f3(?)
[SEC] sleep 50ms
set sequence pos 3
set sequence pos 3
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 0
(0)fe event: status 0, inversion off, m_tuning 1
(0)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x21d32b8 running
[eEPGCache] channel 0x21d32b8 running
[EPGC] next update in 2 sec
stop release channel timer
RemovePopup, id = ZapError
[SEC] sleep 500ms
use pmtpid 0030 for service_id 2f3a
[Dish] tuning failed
eventNewProgramInfo 0 0
have 1 video stream(s) (00a9), and 1 audio stream(s) (0049), and the pcr pid is
00a9, and the text pid is 0050
allocate demux
TuxTxt cache cleared
decoder state: play, vpid=169, apid=73
DMX_SET_PES_FILTER(0xa9) - pcr - ok
DMX_SET_PES_FILTER(0x49) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 0 - ok
DMX_SET_PES_FILTER(0xa9) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x50) - ttx - ok
VIDEO_CONTINUE - ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
AUDIO_CHANNEL_SELECT(0) - ok
disable teletext subtitles page ffffffffffffffff (und)
[__evUpdatedInfo]
[writeChannelName]
vfd display text: n-tv
[showCrypted]
[showDolby]
[showMp3]
[eDVBCAService] new service 1:0:1:2F3A:441:1:C00000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:1:2F3A:441:1:C00000:0:0:0:
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
[__evUpdatedEventInfo]
[EPGC] start caching events(1394745637)
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 5
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
Timeout!
[EPGC] abort non avail schedule other reading
[EPGC] abort non avail netmed schedule reading
[EPGC] abort non avail netmed schedule other reading
[EPGC] abort non avail FreeSat schedule_other reading
[EPGC] abort non avail viasat reading
[EPGC] nownext finished(1394745644)
[__evUpdatedInfo]
[writeChannelName]
vfd display text: n-tv
[showCrypted]
[showDolby]
[showMp3]
[__evUpdatedInfo]
[writeChannelName]
vfd display text: n-tv
[showCrypted]
[showDolby]
[showMp3]
[__evUpdatedInfo]
[writeChannelName]
vfd display text: n-tv
[showCrypted]
[showDolby]
[showMp3]
[__evUpdatedInfo]
[writeChannelName]
vfd display text: n-tv
[showCrypted]
[showDolby]
[showMp3]
[Autologin DynDNS] timerstart
[Autologin DynDNS] autologin enabled: True
[Autologin DynDNS] Last successful login: 2014-03-09
[Autologin DynDNS] i.e. time difference: 4 days, 0:00:00
[eDVBLocalTimerHandler] diff is 0
[eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
[eDVBLocalTimerHandler] not changed
[EPGC] schedule finished(1394745658)
[EPGC] stop caching events(1394745658)
[EPGC] next update in 60 min

[balkanac82]

Hier der Log vom Start an.

Log


#Log file from Morlys SH4 STB Admin Tool from: Do Mrz 13 2014, 22:09:10

@ ?Ld?Õé·Ý[ûÿÿ¿ÿ


Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD


U-Boot 1.3.1 (Dec 23 2011 - 14:26:53) - stm23_0043 - YW 1.0.022 Rel

DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 07 00 00 d0 29

Hit ESC to stop autoboot: 3  2  1  0

Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
Image Name: Linux-2.6.32.61_stm24_0212
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1915513 Bytes = 1.8 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.61_stm24_0212
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1915513 Bytes = 1.8 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 90700d029

Starting kernel console=ttyAS1,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 rw ip=172.100.100.249:172.100.100.174:172.100.100.174 :255.255.0.0:LINUX7109:eth0:off bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 nwhwconf=device:eth0,hwaddr:24:00:07:00:D0:29 Manufacture=Spark-Project STB_ID=09:00:07:00:00:D0:29 - 0x00000000 - 0 ...


INIT: version 2.86 booting

init frontpanel
Mount /dev in tmpfs
Copying device nodes to /dev
Starting portmap daemon....
Loading autofs
Starting autofs
Mounting local filesystems...
mount: mounting LABEL=RECORD on /hdd failed: No such file or directory
Cleaning /tmp.
Hostname: SPARK.
init stmfb
LOADING MODULES
load firmware
copLoadFile (file /boot/audio.elf)
ustslave: Kernel Version: 24
base_address 0x40400000
seeking to 0
seeking to 5e00
seeking to 12460
seeking to 1ab60
seeking to 154300
seeking to 154338
seeking to 154370
seeking to 191a58
seeking to 191a60
seeking to 191a68
seeking to 191a70
seeking to 1aae40
seeking to 1aaf00
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x40000000
seeking to 0
seeking to 60980
seeking to 148478
seeking to 1484b0
seeking to 1484e8
seeking to 158858
seeking to 158864
seeking to 158880
seeking to 184d94
seeking to 186e00
init embx
init AVS
skip mpeg2
insmod: can't insert '/lib/modules/lnb.ko': Input/output error
insmod: read error from '/lib/modules/': Is a directory
insmod: can't insert '/lib/modules/': Is a directory
starting telnetd
lircd-0.9.0[1164]: lircd(default) ready, using /var/run/lirc/lircd

Starting FTP server: Model: spark
vBoxType: 11
Input device name: "fulan front panel buttons"
vsftpd.
Input device name: "TDT RC event driver"
Selected Remote: Spark RemoteControl
RemoteControl Map:
STANDBY - 25 - 116
MUTE - 85 - 113
V.FORMAT - ad - 47
TV/SAT - c5 - 390
0BUTTON - 57 - 11
1BUTTON - b5 - 2
2BUTTON - 95 - 3
3BUTTON - bd - 4
4BUTTON - f5 - 5
5BUTTON - d5 - 6
6BUTTON - fd - 7
7BUTTON - 35 - 8
8BUTTON - 15 - 9
9BUTTON - 3d - 10
BACK - 7f - 158
INFO - a7 - 358
AUDIO - 35 - 392
VOL+ - C7 - 115
VOL- - DD - 114
PAGE+ - 07 - 104
PAGE- - 5F - 109
DOWN - 0f - 108
UP - 27 - 103
RIGHT - af - 106
LEFT - 6d - 105
OK/LIST - 2f - 352
MENU - 65 - 139
GUIDE - 8f - 365
EXIT - 4d - 102
FAV - 87 - 364
RED - 7d - 398
GREEN - ff - 399
YELLOW - 3f - 400
BLUE - bf - 401
REWIND - 1f - 168
PAUSE - 37 - 119
PLAY - b7 - 207
FASTFORWARD - 97 - 208
RECORD - 45 - 167
STOP - f7 - 128
SLOWMOTION - 5d - 409
ARCHIVE - 75 - 361
SAT - 1d - 381
STEPBACK - 55 - 412
STEPFORWARD - d7 - 407
MARK - 8f - 365
TV/RADIO - 77 - 378
USB - 95 - 206
TIMER - 8d - 359
Supports Long KeyPress: 1
processComplex >
Using period=120 delay=10
lircd-0.9.0[1164]: accepted new client on /var/run/lirc/lircd

[SEM] DOWN
Mounting local filesystems...
Deconfiguring network interfaces... ifdown: interface wlan0 not configured
done.
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... udhcpc (v1.21.1) started
Sending discover...
mount: mounting LABEL=RECORD on /hdd failed: No such file or directory
starting e2->
[set_was_timer_wakeup] no timer aktiv
Simple mixer control 'Analog',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 6 [60%] [on]
Simple mixer control 'SPDIF',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 6 [60%] [on]
Simple mixer control 'HDMI',0
Sending discover...
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 6 [60%] [on]
Sending select for 192.168.178.23...
Lease of 192.168.178.23 obtained, lease time 864000
route: SIOCDELRT: No such process
adding dns 192.168.178.1
ifconfig: SIOCGIFFLAGS: No such device
done.
mount: mounting LABEL=RECORD on /hdd failed: No such file or directory
tools/eplayer2.c >
Output
mode 1920, 1080, 32
stride = 7680, width 1920
15360k video mem
[playback/playback.c:PlaybackOpen] URI=file:///boot/bootvideo.mkv
[container/text_srt.c:Command]
[container/text_srt.c:SrtGetSubtitle]
[container/text_srt.c:SrtGetSubtitle] file: /boot/bootvideo.mkv
[container/text_srt.c:SrtGetSubtitle] folder: /boot
[container/text_srt.c:SrtGetSubtitle] ext: mkv
[container/text_srt.c:SrtGetSubtitle] basename: bootvideo
[container/text_srt.c:SrtGetSubtitle] /boot/bootvideo
/boot | bootvideo | mkv
[container/text_srt.c:SrtGetSubtitle] <
[container/text_srt.c:Command] ret = 0
[container/text_ssa.c:Command]
[container/text_ssa.c:SsaGetSubtitle]
[container/text_ssa.c:SsaGetSubtitle] file: /boot/bootvideo.mkv
[container/text_ssa.c:SsaGetSubtitle] folder: /boot
[container/text_ssa.c:SsaGetSubtitle] ext: mkv
[container/text_ssa.c:SsaGetSubtitle] basename: bootvideo
[container/text_ssa.c:SsaGetSubtitle] /boot/bootvideo
/boot | bootvideo | mkv
[container/text_ssa.c:SsaGetSubtitle] <
[container/text_ssa.c:Command] ret = 0
[container/container_ass.c:container_ass_init] >
[container/container_ass.c:container_ass_init] width 1920, height 1080, share 1, fd 3
[ass] Fontconfig disabled, only default font will be used.
container/container.c::Command
container/container.c::selectContainer
Selected Container: FFMPEG
[container/container_ffmpeg.c:container_ffmpeg_init] >
[container/container_ffmpeg.c:container_ffmpeg_init] filename file:///boot/bootvideo.mkv
[container/container_ffmpeg.c:container_ffmpeg_init] avformat_open_input failed -2 (file:///boot/bootvideo.mkv)
[container/container_ffmpeg.c:container_ffmpeg_init] Cause: No such file or directory
showSinglePic /boot/bootlogo.mvi
VIDEO_SELECT_SOURCE MEMORY (Success)
VIDEO_PLAY (Success)
VIDEO_CONTINUE: (Success)
VIDEO_CLEAR_BUFFER: (Invalid argument)
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
STMFB accel interface available

+ (9) GFBDC
15360k total video mem
7260k usable video mem
5640kB available for acceleration surfaces.
resolution: 720 x 576 x 32 (stride: 2880)
+ (9) gLCDDC
eDBoxLCD::eDBoxLCD >
Error loading config file!

LCD resolution: -1 x -1 x -16 (stride: 2)
+ (9) Font Render Class
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "HDMU RC SPARK" is a remotecontrol
Input device "HDMU RC SPARK" is a remotecontrol
failed to open /dev/input/event2
Input device "HDMU RC SPARK" is a remotecontrol
failed to open /dev/input/event3
Input device "HDMU RC SPARK" is a mouse
Found 4 input devices.
+ (22) Hdmi CEC driver
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
done, found 0 common interface slots
+ (35) CA handler
+ (36) Stream server
[SERVERSOCKET] ERROR on bind() (Address already in use)
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryDVD
+ (41) eServiceFactoryEPlayer3
+ (41) eServiceFactoryHDMI
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
---- opening lame channel db
reading services (version 4)
main thread is non-idle! display spinner!
no spinner DC!
loaded 938 channels/transponders and 14963 services
scanning for frontends..
opening frontend 0
frontend successfully opened
close frontend 0
found 1 adapter, 1 frontends(1 sim) and 2 demux, boxtype 28
RTC not ready... wait for transponder time
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
[ePNG] couldn't open /usr/local/share/enigma2/skin_default/spinner/wait9.png
found 8 spinner!

executing main
setIoPrio best-effort level 3 ok
main thread is non-idle! display spinner!
Failed to open /dev/dbox/fp0
Scanning hardware info
Detected: spark
[Harddisk] enumerating block devices...
Reading satellites.xml
sec config cleared
setSlotInfo for dvb frontend 0 to slotid 0, descr STV090x Multistandard, need rotorworkaround No, enabled Yes, DVB-S2 Yes
slot: 0 configmode: simple
diseqcmode: diseqc_a_b_c_d
sec config completed
3660kB available for acceleration surfaces.
resolution: 1280 x 720 x 32 (stride: 5120)
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse3' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse2' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse1' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse0' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/event3' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/event2' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 22] Invalid argument >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 22] Invalid argument >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mice' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js3' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js2' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js1' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js0' >
Selected keymap does not exist!
Activating language Deutsch
[ePopen] command: ip -o addr show dev eth0
eDBoxLCD::getInstance
[eSocketMMIHandler] created successfully
[SHOUTcast] desktop size 1280x725

getModeList for port Component
getModeList for port Scart
getModeList for port HDMI
getModeList for port HDMI-PC
hotplug on dvi
setMode - port: HDMI mode: 1080i rate: 50Hz
updateColor: HDMI
LINE # automatically generated by enigma 2
LINE
[AutoMount.py] self.automounts without mounts {}
[NetworkBrowser] fallback to default translation for NetworkBrowser
[NetworkBrowser] fallback to default translation for Search for network shares
[NetworkBrowser] fallback to default translation for MountManager
[NetworkBrowser] fallback to default translation for Manage network shares
starting hotplug handler
adding Resource DiseqcTester
resources: {'DiseqcTester': <function DiseqcTesterMain at 0x1819a74>}


[CustomSubservicesPlugin] start

[AutomaticVolumeAdjustment] Starting AutomaticVolumeAdjustment...
[AutomaticVolumeAdjustmentConfig] Loading config file...
[AutomaticVolumeAdjustmentConfig] Loaded -1 entries from config file...
[AutomaticVolumeAdjustment] initialize config values...
Plugin raised exception at WHERE_SESSIONSTART
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 171, in __init__
p(reason=0, session=self)
File "usr/lib/enigma2/python/Plugins/Extensions/WebInterface/plugin.py", line 465, in sessionstart
File "usr/lib/enigma2/python/Plugins/Extensions/WebInterface/plugin.py", line 506, in networkstart
File "usr/lib/enigma2/python/Plugins/Extensions/WebInterface/plugin.py", line 170, in startWebserver
File "usr/lib/enigma2/python/Plugins/Extensions/WebInterface/WebChilds/Toplevel.py", line 61, in getToplevel
File "usr/lib/enigma2/python/Plugins/Extensions/WebInterface/WebChilds/External/__init__.py", line 11, in importExternalModules
File "<string>", line 1, in <module>
File "usr/lib/enigma2/python/Plugins/Extensions/WebInterface/WebChilds/External/Example.py", line 131, in <module>
File "usr/lib/enigma2/python/Plugins/Extensions/WebInterface/WebChilds/External/Example.py", line 24, in checkCams
OSError: [Errno 2] No such file or directory: '/var/emu/start/'
[EPGC] setCacheFile read/write epg data from/to '/hdd/epg.dat'
[SKIN] Parsing embedded skin <embedded-in-'Screensaver'>
warning, skin is missing element boquet in <class 'Screens.ChannelSelection.ChannelSelection'>
fp_control: SW Version 1.03
Model: spark
vBoxType: 11
Selected Model: Edision Spark frontpanel control utility
Spark_init
checkConfig
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S
, WAKEUPDECREMENT 300
18
[SKIN] No skin to read...
warning, skin is missing element From in <class 'Screens.Dish.Dish'>
warning, skin is missing element Goto in <class 'Screens.Dish.Dish'>
warning, skin is missing element tunerName in <class 'Screens.Dish.Dish'>
warning, skin is missing element turnSpeed in <class 'Screens.Dish.Dish'>
RemovePopup, id = ZapError
setValue 75
Setvolume: 75 75 (raw)
Setvolume: 16 16 (-1db)
playing 1:0:1:6DCA:44D:1:C00000:0:0:0:
[__evStart]
[__evSeekableStatusChanged]
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
RemovePopup, id = ZapError
allocate channel.. 044d:0001
opening frontend 0
frontend successfully opened
(0)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 0 Freq 11836500 Pol 0 SR 27500000 INV 2 FEC 3 orbpos 192 system 0 modulation 1 pilot 2, rolloff 0
tuning to 1236 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:1:6DCA:44D:1:C00000:0:0:0:
allocate demux
[ePopen] command: route -n | grep eth0
poll: unhandled POLLERR/HUP/NVAL for fd 29(16)
set sequence pos 3
set sequence pos 4
[SEC] setVoltage 2
[SEC] sleep 200ms
192.168
0.0.0.0
********** end showiframe
VIDEO_SELECT_SOURCE DEMUX (Invalid argument)
nameservers: [[192, 168, 178, 1]]
read configured interface: {'lo': {'dhcp': False}, 'wlan0': {'dhcp': True}, 'eth0': {'dhcp': True}}
self.ifaces after loading: {'eth0': {'preup': False, 'predown': False, 'ip': [192, 168, 178, 23], 'up': True, 'mac': '24:00:07:00:d0:29', 'dhcp': True, 'bcast': [192, 168, 178, 255], 'netmask': [255, 255, 255, 0], 'gateway': [192, 168, 178, 1]}}
poll: unhandled POLLERR/HUP/NVAL for fd 32(16)
[SEC] invalidate current switch params
[SEC] sendDiseqc: e00000(DiSEqC reset)
[SEC] sleep 50ms
[SEC] sendDiseqc: e00003(DiSEqC peripherial power on)
[SEC] sleep 150ms
[SEC] sendDiseqc: e01038f3(?)
[SEC] sleep 50ms
set sequence pos 3
[SEC] setTone 1
[SEC] sleep 10ms
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 0
(0)fe event: status 0, inversion off, m_tuning 1
[SEC] sleep 500ms
(0)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x19fdb08 running
[eEPGCache] channel 0x19fdb08 running
stop release channel timer
eventNewProgramInfo 0 0
have 1 video stream(s) (0065), and 1 audio stream(s) (0066), and the pcr pid is 0065, and the text pid is 0068
allocate demux
TuxTxt cache cleared
decoder state: play, vpid=101, apid=102
DMX_SET_PES_FILTER(0x65) - pcr - ok
DMX_SET_PES_FILTER(0x66) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 0 - ok
DMX_SET_PES_FILTER(0x65) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x68) - ttx - ok
TuxTxt cache cleared
TuxTxt: initialized
TuxTxt service started 68
VIDEO_CONTINUE - ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
AUDIO_CHANNEL_SELECT(0) - ok
disable teletext subtitles page ffffffffffffffff (und)
TuxTxt running thread...(068)
[AutomaticVolumeAdjustment] service changed
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Das Erste
[showCrypted]
[showDolby]
[showMp3]
FE_GET_PROPERTY failed (Invalid argument)
[eDVBCAService] new service 1:0:1:6DCA:44D:1:C00000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:1:6DCA:44D:1:C00000:0:0:0:
RemovePopup, id = ZapError
[eDVBLocalTimerHandler] dont have correction.. set Transponder Diff
[eDVBLocalTimerHandler] update RTC
[eDVBLocalTimerHandler] time update to 22:07:31
[eDVBLocalTimerHandler] m_time_difference is 448059998
[eDVBLocalTimerHandler] set Linux Time
[EPGC] time updated.. start EPG Mainloop
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 5
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
use pmtpid 0064 for service_id 6dca
[Dish] tuning failed
sdt update done!
eventNewProgramInfo 0 0
have 1 video stream(s) (0065), and 3 audio stream(s) (0066, 0067, 006a), and the pcr pid is 0065, and the text pid is 0068
decoder state: play, vpid=101, apid=102
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Das Erste
[showCrypted]
[showDolby]
[showMp3]
FE_GET_PROPERTY failed (Invalid argument)
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Das Erste
[showCrypted]
[showDolby]
[showMp3]
[__evUpdatedEventInfo]
ERROR reading PES (fd=48) - Value too large for defined data type
poll: unhandled POLLERR/HUP/NVAL for fd 48(8)
/bin/fp_control: SW Version 1.03
Model: spark
vBoxType: 11
Selected Model: Edision Spark frontpanel control utility
Spark_init
checkConfig
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S
, WAKEUPDECREMENT 300
Setting Clock to current time: 22:07:42 13-03-2014
[EPGC] 44159 events read from /hdd/epg.dat
[EPGC] next update in 2 sec
[EPGC] start caching events(1394744869)
[EPGC] abort non avail schedule other reading
[EPGC] abort non avail netmed schedule reading
[EPGC] abort non avail netmed schedule other reading
[EPGC] abort non avail FreeSat schedule_other reading
[EPGC] abort non avail viasat reading
[EPGC] nownext finished(1394744878)
/bin/fp_control: SW Version 1.03
Model: spark
vBoxType: 11
Selected Model: Edision Spark frontpanel control utility
Spark_init
checkConfig
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S
, WAKEUPDECREMENT 300
Setting Clock to current time: 22:08:12 13-03-2014
[RCU] key: 3f -> 00000000a25dc03f 00 UP SPARK(default)

KEY: 67 - UP
**** 1383484467 1 ****
[SEM] UP
KEY_PRESS - 67 1
++++ 8 ms ++++
not enough diskspace for timeshift! (less than 200MB)
playing 1:0:1:6D66:437:1:C00000:0:0:0:
[eDVBCAService] free slot 0 demux 0 for service 1:0:1:6DCA:44D:1:C00000:0:0:0:
[eDVBCAService] free service 1:0:1:6DCA:44D:1:C00000:0:0:0:
decoder state: play, vpid=-1, apid=-1
DEMUX_STOP - pcr - ok
DEMUX_STOP - video - ok
VIDEO_STOP - KEY_RELEASE - 67 00 1 1 CAUSE=Timeout
[RCU] key: 3f -> 00000000a25dc03f 01 UP SPARK(default)

KEY: 67 - UP
**** 139 1 ****
---- 108 ms ----
[SEM] DOWN
ok
AUDIO_STOP - ok
DEMUX_STOP - audio - ok
AUDIO_CONTINUE - ok
DEMUX_STOP - ttx - ok
TuxTxt stopped service 68
cleaning up
TuxTxt cache cleared
start release channel timer
[__evStart]
[__evSeekableStatusChanged]
not enough diskspace for timeshift! (less than 200MB)
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
not pauseable.
not enough diskspace for timeshift! (less than 200MB)
RemovePopup, id = ZapError
[eDVBLocalTimerHandler] remove channel 0x19fdb08
[eEPGCache] remove channel 0x19fdb08
[EPGC] abort caching events !!
allocate channel.. 0437:0001
(0)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 0 Freq 11953500 Pol 0 SR 27500000 INV 2 FEC 3 orbpos 192 system 0 modulation 1 pilot 2, rolloff 0
tuning to 1353 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:1:6D66:437:1:C00000:0:0:0:
allocate demux
set sequence pos 3
set sequence pos 3
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 0
(0)fe event: status 0, inversion off, m_tuning 1
(0)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x1bd93d8 running
[eEPGCache] channel 0x1bd93d8 running
[EPGC] next update in 2 sec
stop release channel timer
eventNewProgramInfo 0 0
have 1 video stream(s) (006e), and 1 audio stream(s) (0078), and the pcr pid is 006e, and the text pid is 0082
allocate demux
TuxTxt cache cleared
decoder state: play, vpid=110, apid=120
DMX_SET_PES_FILTER(0x6e) - pcr - ok
DMX_SET_PES_FILTER(0x78) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 0 - ok
DMX_SET_PES_FILTER(0x6e) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x82) - ttx - ok
TuxTxt cache cleared
TuxTxt: initialized
TuxTxt service started 82
VIDEO_CONTINUE - ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
disable teletext subtitles page ffffffffffffffff (und)
TuxTxt running thread...(082)
[AutomaticVolumeAdjustment] service changed
[__evUpdatedInfo]
[writeChannelName]
vfd display text: ZDF
[showCrypted]
[showDolby]
[showMp3]
FE_GET_PROPERTY failed (Invalid argument)
[eDVBCAService] new service 1:0:1:6D66:437:1:C00000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:1:6D66:437:1:C00000:0:0:0:
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
[EPGC] start caching events(1394744898)
[__evUpdatedEventInfo]
main thread is non-idle! display spinner!
RemovePopup, id = ZapError
[SEC] sleep 500ms
[eDVBLocalTimerHandler] diff is -10
[eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
[eDVBLocalTimerHandler] update RTC
[eDVBLocalTimerHandler] time update to 22:08:11
[eDVBLocalTimerHandler] m_time_difference is -10
[eDVBLocalTimerHandler] set Linux Time
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 5
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
ERROR reading PES (fd=48) - Value too large for defined data type
poll: unhandled POLLERR/HUP/NVAL for fd 48(8)
use pmtpid 0064 for service_id 6d66
[Dish] tuning failed
eventNewProgramInfo 0 0
have 1 video stream(s) (006e), and 4 audio stream(s) (0078, 0079, 007a, 007d), and the pcr pid is 006e, and the text pid is 0082
decoder state: play, vpid=110, apid=120
[__evUpdatedInfo]
[writeChannelName]
vfd display text: ZDF
[showCrypted]
[showDolby]
[showMp3]
FE_GET_PROPERTY failed (Invalid argument)
poll: unhandled POLLERR/HUP/NVAL for fd 50(16)
sdt update done!
[__evUpdatedEventInfo]
[EPGC] abort non avail schedule other reading
[EPGC] abort non avail netmed schedule reading
[EPGC] abort non avail netmed schedule other reading
[EPGC] abort non avail FreeSat schedule_other reading
[EPGC] abort non avail viasat reading
[__evUpdatedInfo]
[writeChannelName]
vfd display text: ZDF
[showCrypted]
[showDolby]
[showMp3]
[EPGC] nownext finished(1394744899)
[EPGC] schedule finished(1394744923)
[EPGC] stop caching events(1394744923)
[EPGC] next update in 60 min

[bonkel]

irgendwas passt da generell nicht

/var/emu/start/

warum ist das nich bei dir vorhanden?

[balkanac82]

weil ich den AlternativeSoftCamManager benutze. Kommt deshalb der Spinner?

[bonkel]

weiss ich nich, halte von dem plugin nichts.......
aber klar, plugins können auch nen spinner verursachen und den betrieb verlangsamen...

sicher nich sinnvoll, Default ordner zu löschen....

[santa]

rangerm, bonkel hat das andere gefixt, baue neue images.

Die haben was im pli verändert, was leider bedeutet das alle skins angepasst werden müssen.
das wiederum bedeutet, das die skins dann nur noch auf den alten oder den neuen images gehen.

[balkanac82]

Auch im deaktivierten Zustand zeigt sich der Spinner beim Zappen. Mit dem alten Kernel war das kein Problem.

[santa]

installier mal bitte neu, nach erstassi nichts weiter machen, dann mal testen.

[rangerm]

Nur kein Stress :)

Ich weiß nicht ob vielleicht benny auch mich meinte, weil bei mir finde ich auch kein Starten des emu im Log.

Kann euch aber versichern das emu läuft sehr gut sogar :D

Zum log von balkanac82.

Was mir nur immer ins Auge sticht ist dieses Timeshift, was natürlich den spinner beim umschalten erklären würde.

[balkanac82]

Wo kann ich das Timeshift deaktivieren? Ist kommisch das, dass mitläuft obwohl ich es garnicht nutze. :sm57:

[rangerm]

Also wenn du es nicht jedes mal Manuel einschaltest wüsste ich nur noch das Plugin perm Timeshift.

Aber da du es nicht drauf hast keine Ahnung

[bonkel]

im menü Einstellungen, System, benutzeroberfläche automatischer timeshift-start nach....sollte deaktiviert sein


das plugin permanent timeshift, läuft generell nicht mehr mit dem Image, da nun fest im System

[balkanac82]

Ich habe mal in der Benutzeroberfläche geschaut.
Automatischer Timeshift-Start nach Deaktiviert
Zeige eine Warning beim Stoppen des Timeshifts Ja

EDIT: Hab das Problem lösen können. Wie immer lag es an den kleinigkeiten.Habe drei Plugins die ich immer benutze in das neue Image reingeschoben per FTP. Die habe ich alle gelöscht und die Box neu gestartet. Danach hatte sich der Spinner nicht mehr gezeigt. Offentsichtlich hat sich ein Plugin nicht mit dem neuen Kernel vertragen. Habe nun alle drei über das Feed geladen und es läuft alles ohne Probleme.
Danke für eure Hilfe

PS. Es lag nicht am AlternativSoftcamManager ;)

[dmrcr7]

Hallo,
Bei mir (Argus Pingu Plus) macht es Probleme beim OSCAM, Netzwerk verhält sich eingenartig (erhält keine IP, oder der DNS konnte nicht erreicht werden, seltsamerweise jedes mal andere FM nach Netzwerk restart). Nach wenigen Stunden ging es dann plötzlich mit einer festen IP
Beim installieren von Plugins, geht das Ausführfenster gleich zu.
Setze heute noch einmal auf, hoffe war nur ein locales problem mit OSCAM666. Oscam 8*** lies sich zwar installieren, konnte auch nach Reboot nicht starten! Bei OSCAM 7** kam ebenfalls nichts. MGCAM ging auf Anhieb.

Ansonsten Super schnell, wie bereits beim Booten preisgegen wird. http://www.digital-eliteboard.com/images/smilies/good.gif

Update: nach dem ich neu geflasht habe, ging oscam666 zwar immer noch nicht mit meinen Configs, jedoch hat die Installation von Oscam 8*** gut hingehauen und läuft alles bestens.
Openvpn geht ebenfalls recht einfach.
Kann mir jemand sagen wo ich die Reihenfolge ändern kann, damit erst openvpn sich Connectet und erst darauf das Emu???

[tommek15]

Ich habe ein Problem mit der Transponderfrequenz 11914 H 27500 10/9. Auf Spark tun OK, bis der Enigma kein Signal auf sie.

[rangerm]

Auf den Transponder liegen z.b Sky cinema HD,Sky Bundesliga 2 HD genau neuen Sender findet er.

Zur Korrektur du meinst 11914 H 27500 9/10 anders geht es garnicht zum Einstellen.

Da ich mir nicht vorstellen kann das es ein allgemeines Problem ist weil jeder bei Fußball aufschreien würde liegt der Fehler bei dir im System.

Was mir Spontan einfällt ist das unter Spark der Tuner nicht so sensibel ist, daher wäre mal interessant welche Signal Qualität also SNR Wert du auf den Sat hast.

Wenn er z.b unter Spark gerade noch ein Signal knapp über 50 % bekommt kann es unter E2 schon sein das er nix findet.