wayne
16.06.2014, 22:21
Hallihallo!
Bitte um Nachsicht, bin Anfänger...:o
Ich habe folgendes Problem, was schon mal vor einem Jahr vom meinem Händler repariert wurde. Jetzt will ich aber mal...
Enigma startet plötzlich nicht mehr. Es wird nur noch "boot" angezeigt. Terminal meldet dann und bleibt stehen:
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2175496 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.59_stm24_0211
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2175496 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
found phy at addres = 2
stmac_phy_get_addr(): id1 = 0x0, id2 = 0x8201
stb_id = 90800bf7
Starting kernel console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw in
it=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 rw ip=172.1
00.100.249:172.100.100.174:172.100.100.174:255.255 .0.0:LINUX7109:eth0:off bigphy
sarea=6000 stmmaceth=msglvl:0,phyaddr:2,watchdog:5000 nwhwconf=device:eth0,hwadd
r:24:00:08:00:0B:F7 Manufacture=Spark-Project STB_ID=09:00:08:00:00:0B:F7 - 0x00
000000 - 0 ...
Spark startet problemlos!
Update mit USB-Stick (viele verschiedene versucht, FAT und FAT32) klappt nicht, nach "Force" kommt "Fact" und bleibt stehen. Kein 770!
Terminal meldet dann und bleibt stehen:
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 0b f7
Hit ESC to stop autoboot: 5
Force command mode:Select boot (current boot system : enigma2):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force Factory mode
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices...
Das Flashen über TFTP:
Force command mode:Select boot (current boot system : enigma2):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force Factory mode
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Can't read from device 0 **
** Unable to use usb 0:1 for fatload **
Warning: MAC addresses don't match:
HW MAC address: FF:FF:FF:FF:FF:FF
"ethaddr" value: 00:80:E1:12:06:38
Using MAC Address 00:80:E1:12:06:38
*** ERROR: `ethaddr' not set
Die bootargs habe ich neu gesetzt wie in der angehängten txt
Was könnte ich noch versuchen? Was mache ich noch falsch?
Danke und Grüße,
wayne
Bitte um Nachsicht, bin Anfänger...:o
Ich habe folgendes Problem, was schon mal vor einem Jahr vom meinem Händler repariert wurde. Jetzt will ich aber mal...
Enigma startet plötzlich nicht mehr. Es wird nur noch "boot" angezeigt. Terminal meldet dann und bleibt stehen:
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2175496 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.59_stm24_0211
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2175496 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
found phy at addres = 2
stmac_phy_get_addr(): id1 = 0x0, id2 = 0x8201
stb_id = 90800bf7
Starting kernel console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw in
it=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 rw ip=172.1
00.100.249:172.100.100.174:172.100.100.174:255.255 .0.0:LINUX7109:eth0:off bigphy
sarea=6000 stmmaceth=msglvl:0,phyaddr:2,watchdog:5000 nwhwconf=device:eth0,hwadd
r:24:00:08:00:0B:F7 Manufacture=Spark-Project STB_ID=09:00:08:00:00:0B:F7 - 0x00
000000 - 0 ...
Spark startet problemlos!
Update mit USB-Stick (viele verschiedene versucht, FAT und FAT32) klappt nicht, nach "Force" kommt "Fact" und bleibt stehen. Kein 770!
Terminal meldet dann und bleibt stehen:
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 0b f7
Hit ESC to stop autoboot: 5
Force command mode:Select boot (current boot system : enigma2):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force Factory mode
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices...
Das Flashen über TFTP:
Force command mode:Select boot (current boot system : enigma2):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force Factory mode
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Can't read from device 0 **
** Unable to use usb 0:1 for fatload **
Warning: MAC addresses don't match:
HW MAC address: FF:FF:FF:FF:FF:FF
"ethaddr" value: 00:80:E1:12:06:38
Using MAC Address 00:80:E1:12:06:38
*** ERROR: `ethaddr' not set
Die bootargs habe ich neu gesetzt wie in der angehängten txt
Was könnte ich noch versuchen? Was mache ich noch falsch?
Danke und Grüße,
wayne