Spark 7162 - HDMU 12614 Issues

[ibero96]

GM Triplex 2 x DVB-S2 1 x DVB-T located in France - with this image has 2 problems, one serious one annoying.

1) Serious;

DVB-T HD channels shave no sound with the audio.elf installed with this image - no AC3 and not even if downmixed PCM - nothing, not a single peep. SD channels sounds are fine. Replaced the HDMU audio.elf with a copy from PKT V4 and now have HD channel sound but only downmixed to PCM, not AC3.

DVB-S2 HD channels are prefect - full AC3 decode 5.1 where broadcast.

2) Annoying

The time display on the VFD is seriously crazy - starts out fine and then at some point goes berserk - I suspected it was losing sync over midnight but not so - seems to decide to display random time at any point after boot. Restarting image sometimes corrects it but not always and it will go haywire again at some point anyway. I thought at first it was switching to displaying uptime instead of current time but not so - time appears random. Enigma2 knows the correct time - it's only the VFD display that is wrong. The date is always displayed correctly!

Any ideas?

Plugins are fairly common -

Autobouqets
Autotimer
Clearmem
Change spinner
Partnerbox
Crossepg
CoolTV
EMC
TS-Edit

any clues there?

Cheers...

Andy

[ibero96]

And if I've understood this post correctly I confirm that this is also true - there are no symbols in the VFD any more other than time, channel and HDD

http://www.hdmedia-universe.com/board/showthread.php?7180-Hdmu-12614-amp-vfd&p=83418#post83418

[lucsch]

I just installed the flash version on a Amiko Alien2. The VFD gives only the clock and "boot".

[lucsch]

Now I have installed HDMU on USB, and the result is the same.

Here the serial log from start.


Board: STx7105-PDK [32-bit mode]


U-Boot 1.3.1 (Jul 24 2012 - 14:04:09) - stm23_0051 - YW_1.1.006 overclock

DRAM: 256 MiB
Panel: DVFD
NAND: Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
512 MiB
SPI: SPI Device status = 0x9c
info: found S25FL016K (2MiB) device (page=256,erase=65536)
SPI device status=0x9c
warning: SPI device may be write-protected (status=0x9c)
In: serial
Out: serial
Err: serial
Ident ic exist
Ident ic get stb id
IdentID : 0c 00 0a 00 00 42 0e
Hit ESC to stop autoboot: 0

Loading from NAND 512MiB 3,3V 8-bit, offset 0x18400000
Image Name: Linux-2.6.32.61_stm24_0215
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2332699 Bytes = 2.2 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.61_stm24_0215
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2332699 Bytes = 2.2 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
stmac_phy_get_addr(): id1 = 0xffff, id2 = 0xffff
found phy at addres = 2
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = c0a0042e

Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=
1 rw ip=192.168.40.63:192.168.40.19:192.168.40.1:255.25 5.255.0:Enigma2:eth0:off bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:2
,watchdog:5000 rootdelay=9 nwhwconf=device:eth0,hwaddr:30:00:0A:00:42:0E Manufacture=Spark-Project STB_ID=0C:00:0A:00:00:42:0
E - 0x00000000 - 0 ...

INIT: version 2.88 booting
init frontpanel
Mount /dev in tmpfs
Copying device nodes to /dev
Starting portmap daemon....
Loading autofs
Starting autofs
Mounting local filesystems...
swapon: using /etc/fstab
Cleaning /tmp.
Hostname: SPARK7162.
init stmfb
LOADING MODULES
load firmware
copLoadFile (file /boot/audio.elf)
ustslave: Kernel Version: 24
base_address 0x40400000
seeking to 0
seeking to 5e00
seeking to 12460
seeking to 1ab60
seeking to 154300
seeking to 154338
seeking to 154370
seeking to 191a58
seeking to 191a60
seeking to 191a68
seeking to 191a70
seeking to 1aae40
seeking to 1aaf00
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x40000000
seeking to 0
seeking to e2dc0
seeking to e2df8
seeking to e2e30
seeking to e8fe8
seeking to e8ff4
seeking to e9000
seeking to 115710
seeking to 117800
init embx
init AVS
skip mpeg2
insmod: : No such file or directory
insmod: : No such file or directory
insmod: /lib/modules/.ko: module not found
lircd-0.9.0[1122]: lircd(default) ready, using /var/run/lirc/lircd
showSinglePic /boot/bootlogo.mvi
VIDEO_SELECT_SOURCE MEMORY (Success)
VIDEO_PLAY (Success)
VIDEO_CONTINUE: (Success)
VIDEO_CLEAR_BUFFER: (Invalid argument)
Model: 'spark7162'
vBoxType: 11
Input device name: "fulan front panel buttons"
Input device name: "TDT RC event driver"
Selected Remote: Spark RemoteControl
RemoteControl Map:
STANDBY - 25 - 116
MUTE - 85 - 113
V.FORMAT - ad - 47
TV/SAT - c5 - 390
0BUTTON - 57 - 11
1BUTTON - b5 - 2
2BUTTON - 95 - 3
3BUTTON - bd - 4
4BUTTON - f5 - 5
5BUTTON - d5 - 6
6BUTTON - fd - 7
7BUTTON - 35 - 8
8BUTTON - 15 - 9
9BUTTON - 3d - 10
BACK - 7f - 158
INFO - a7 - 358
AUDIO - 35 - 392
VOL+ - C7 - 115
VOL- - DD - 114
PAGE+ - 07 - 104
PAGE- - 5F - 109
DOWN - 0f - 108
UP - 27 - 103
RIGHT - af - 106
LEFT - 6d - 105
OK/LIST - 2f - 352
MENU - 65 - 139
GUIDE - 8f - 365
EXIT - 4d - 102
FAV - 87 - 364
RED - 7d - 398
GREEN - ff - 399
YELLOW - 3f - 400
BLUE - bf - 401
REWIND - 1f - 168
PAUSE - 37 - 119
PLAY - b7 - 207
FASTFORWARD - 97 - 208
RECORD - 45 - 167
STOP - f7 - 128
SLOWMOTION - 5d - 409
ARCHIVE - 75 - 361
SAT - 1d - 381
STEPBACK - 55 - 412
STEPFORWARD - d7 - 407
MARK - 8f - 365
TV/RADIO - 77 - 378
USB - 95 - 206
TIMER - 8d - 359
Supports Long KeyPress: 1
processComplex >
Using period=120 delay=10
lircd-0.9.0[1122]: accepted new client on /var/run/lirc/lircd
[SEM] DOWN
Mounting local filesystems...
Deconfiguring network interfaces... done.
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... done.
swapon: using /etc/fstab
[set_was_timer_wakeup] no timer aktiv
starting e2->
Simple mixer control 'SPDIF',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 6 [60%] [on]
Simple mixer control 'Analog',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 6 [60%] [on]
Simple mixer control 'HDMI',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 6 [60%] [on]
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
STMFB accel interface available

+ (9) GFBDC
20480k total video mem
12380k usable video mem
10760kB available for acceleration surfaces.
resolution: 720 x 576 x 32 (stride: 2880)
+ (9) gLCDDC
eDBoxLCD::eDBoxLCD >
Error loading config file!

LCD resolution: -1 x -1 x -438444568 (stride: 1128547395)
+ (9) Font Render Class
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "HDMU RC SPARK" is a remotecontrol
Input device "HDMU RC SPARK" is a remotecontrol
failed to open /dev/input/event2
Input device "HDMU RC SPARK" is a mouse
failed to open /dev/input/event3
Input device "HDMU RC SPARK" is a mouse
Found 4 input devices.
+ (22) Hdmi CEC driver
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
done, found 0 common interface slots
+ (35) CA handler
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryDVD
+ (41) eServiceFactoryEPlayer3
+ (41) eServiceFactoryHDMI
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
+ (41) Encoders
+ (41) Stream server
[SERVERSOCKET] ERROR on bind() (Address already in use)
reached rl 70
---- opening lame channel db
reading services (version 4)
loaded 245 channels/transponders and 6175 services
scanning for frontends..
opening frontend 0
frontend successfully opened
close frontend 0
opening frontend 1
frontend successfully opened
close frontend 1
opening frontend 2
frontend successfully opened
close frontend 2
found 1 adapter, 3 frontends(3 sim) and 4 demux, boxtype 29
RTC not ready... wait for transponder time
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
[ePNG] couldn't open /usr/local/share/enigma2/skin_default/spinner/wait13.png
found 12 spinner!

executing main
setIoPrio best-effort level 3 ok
Failed to open /dev/dbox/fp0
Scanning hardware info
Detected: spark7162
[Harddisk] enumerating block devices...
new Harddisk sda -> /dev/sda -> /dev/sda
main thread is non-idle! display spinner!
Reading satellites.xml
Reading terrestrial.xml
sec config cleared
setSlotInfo for dvb frontend 0 to slotid 0, descr Tuner3-T/T2(T/T2/C), need rotorworkaround No, enabled No, DVB-S2 No
setSlotInfo for dvb frontend 1 to slotid 1, descr Tuner1-Sat, need rotorworkaround No, enabled Yes, DVB-S2 Yes
setSlotInfo for dvb frontend 2 to slotid 2, descr Tuner2-Sat, need rotorworkaround No, enabled No, DVB-S2 Yes
slot: 1 configmode: simple
diseqcmode: diseqc_a_b_c_d
slot: 2 configmode: nothing
sec config completed
Renumbering...
8780kB available for acceleration surfaces.
resolution: 1280 x 720 x 32 (stride: 5120)
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse0' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js1' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 25] Inappropriate ioctl for device >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse3' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse1' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 22] Invalid argument >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 22] Invalid argument >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js0' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse2' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js2' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/event3' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/event2' >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js3' >
Selected keymap does not exist!
Activating language English
[ePopen] command: ip -o addr show dev eth0
eDBoxLCD::getInstance
LINE # automatically generated by enigma 2
LINE
[AutoMount.py] self.automounts without mounts {}
[NetworkBrowser] fallback to default translation for NetworkBrowser
[NetworkBrowser] fallback to default translation for Search for network shares
[NetworkBrowser] fallback to default translation for MountManager
[NetworkBrowser] fallback to default translation for Manage network shares
getModeList for port Component
getModeList for port Scart
getModeList for port HDMI
getModeList for port HDMI-PC
hotplug on dvi
setMode - port: HDMI mode: 1080i rate: 50Hz
updateColor: HDMI
[eSocketMMIHandler] created successfully
Plugin Extensions/WebInterface failed to load: No module named plugin
starting hotplug handler
adding Resource DiseqcTester
resources: {'DiseqcTester': <function DiseqcTesterMain at 0xde44fc>}
[EPGC] setCacheFile read/write epg data from/to '/hdd/epg.dat'
[SKIN] Parsing embedded skin <embedded-in-'Screensaver'>
warning, skin is missing element boquet in <class 'Screens.ChannelSelection.ChannelSelection'>
fp_control: SW Version 1.04
Model: spark7162
vBoxType: 11
Selected Model: Edision Spark frontpanel control utility
Spark_init
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S
, WAKEUPDECREMENT 300
18
setbrightness: : Timer expired
warning, skin is missing element RassLogo in <class 'Screens.RdsDisplay.RdsInfoDisplay'>
[SKIN] No skin to read...
warning, skin is missing element UnhandledKeyPixmap in <class 'Screens.UnhandledKey.UnhandledKey'>
warning, skin is missing element From in <class 'Screens.Dish.Dish'>
warning, skin is missing element Goto in <class 'Screens.Dish.Dish'>
warning, skin is missing element tunerName in <class 'Screens.Dish.Dish'>
warning, skin is missing element turnSpeed in <class 'Screens.Dish.Dish'>
warning, skin is missing element posGoto in <class 'Screens.Dish.Dish'>
warning, skin is missing element posFrom in <class 'Screens.Dish.Dish'>
warning, skin is missing element turnTime in <class 'Screens.Dish.Dish'>
RemovePopup, id = ZapError
setValue 5
Setvolume: 5 5 (raw)
Setvolume: 60 60 (-1db)
********** end showiframe
VIDEO_SELECT_SOURCE DEMUX (Invalid argument)
playing 1:0:1:6DCA:44D:1:C00000:0:0:0:
[__evStart]
[__evSeekableStatusChanged]
not pauseable.
not pauseable.
not pauseable.
RemovePopup, id = ZapError
allocate channel.. 044d:0001
opening frontend 1
frontend successfully opened
(1)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 0 Freq 11836500 Pol 0 SR 27500000 INV 2 FEC 3 orbpos 192 system 0 modulation 1 pilot 2, rolloff 0
tuning to 1236 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:1:6DCA:44D:1:C00000:0:0:0:
allocate demux
[ePopen] command: route -n | grep eth0
poll: unhandled POLLERR/HUP/NVAL for fd 30(16)
set sequence pos 3
set sequence pos 4
[SEC] setVoltage 2
[SEC] sleep 200ms
192.168
0.0.0.0
nameservers: [[208, 67, 220, 220], [208, 67, 222, 222]]
read configured interface: {'lo': {'dhcp': False}, 'eth0': {'dhcp': False, 'netmask': [255, 255, 255, 0], 'gateway': [192, 16
8, 1, 1], 'address': [192, 168, 1, 75]}}
self.ifaces after loading: {'eth0': {'preup': False, 'predown': False, 'ip': [192, 168, 1, 75], 'up': True, 'mac': '30:00:0a:
00:42:0e', 'dhcp': False, 'bcast': [192, 168, 1, 255], 'netmask': [255, 255, 255, 0], 'gateway': [192, 168, 1, 1]}}
AT plugin not found
ER plugin not found
[OpenWebif] no plugins to load
[OpenWebif] started on 80
[OpenWebif] started on 443
poll: unhandled POLLERR/HUP/NVAL for fd 35(16)
[SEC] invalidate current switch params
[SEC] sendDiseqc: e00000(DiSEqC reset)
[SEC] sleep 50ms
[SEC] sendDiseqc: e00003(DiSEqC peripherial power on)
[SEC] sleep 150ms
[SEC] sendDiseqc: e01038f3(?)
[SEC] sleep 50ms
set sequence pos 3
[SEC] setTone 1
[SEC] sleep 10ms
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 1
(1)fe event: status 0, inversion off, m_tuning 1
(1)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x11bc518 running
[eEPGCache] channel 0x11bc518 running
stop release channel timer
eventNewProgramInfo 0 0
have 1 video stream(s) (0065), and 1 audio stream(s) (0066), and the pcr pid is 0065, and the text pid is 0068
allocate demux
TuxTxt cache cleared
decoder state: play, vpid=101, apid=102
DMX_SET_PES_FILTER(0x65) - pcr - ok
DMX_SET_PES_FILTER(0x66) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 0 - ok
DMX_SET_PES_FILTER(0x65) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x68) - ttx - ok
TuxTxt cache cleared
TuxTxt: initialized
TuxTxt service started 68
VIDEO_CONTINUE - TuxTxt running thread...(068)
ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
AUDIO_CHANNEL_SELECT(0) - ok
disable teletext subtitles page ffffffffffffffff (und)
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Das Erste
[showCrypted]
[showDolby]
[showMp3]
[eDVBCAService] new service 1:0:1:6DCA:44D:1:C00000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:1:6DCA:44D:1:C00000:0:0:0:
RemovePopup, id = ZapError
[SEC] sleep 500ms
[NetworkBrowser] fallback to default translation for NetworkBrowser
[eDVBLocalTimerHandler] dont have correction.. set Transponder Diff
[eDVBLocalTimerHandler] update RTC
[eDVBLocalTimerHandler] time update to 12:09:48
[eDVBLocalTimerHandler] m_time_difference is 460894143
[eDVBLocalTimerHandler] set Linux Time
[EPGC] time updated.. start EPG Mainloop
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Das Erste
[showCrypted]
[showDolby]
[showMp3]
[NetworkBrowser] fallback to default translation for Search for network shares
[NetworkBrowser] fallback to default translation for MountManager
use pmtpid 0064 for service_id 6dca
[NetworkBrowser] fallback to default translation for Manage network shares
sdt update done!
Plugin Extensions/WebInterface failed to load: No module named plugin
[Dish] tuning failed
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 5
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
eventNewProgramInfo 0 0
have 1 video stream(s) (0065), and 3 audio stream(s) (0066, 0067, 006a), and the pcr pid is 0065, and the text pid is 0068
decoder state: play, vpid=101, apid=102
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Das Erste
[showCrypted]
[showDolby]
[showMp3]
AT plugin not found
ER plugin not found
[OpenWebif] no plugins to load
[OpenWebif] failed to listen on Port 80
[OpenWebif] failed to listen on Port 443
[__evUpdatedEventInfo]
[EPGC] 20068 events read from /hdd/epg.dat
[EPGC] next update in 2 sec
[EPGC] start caching events(1407578991)
[EPGC] nownext finished(1407578999)
/bin/fp_control: SW Version 1.04
Model: spark7162
vBoxType: 11
Selected Model: Edision Spark frontpanel control utility
Spark_init
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S
, WAKEUPDECREMENT 300
Setting Clock to current time: 12:10:13 09-08-2014
[EPGC] schedule finished(1407579020)
[EPGC] stop caching events(1407579020)
[EPGC] next update in 60 min
/bin/fp_control: SW Version 1.04
Model: spark7162
vBoxType: 11
Selected Model: Edision Spark frontpanel control utility
Spark_init
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S
, WAKEUPDECREMENT 300
Setting Clock to current time: 12:10:43 09-08-2014