Ergebnis 1 bis 10 von 20

Hybrid-Darstellung

  1. #1
    Boardgründer/Administrator Avatar von bonkel
    Registriert seit
    03.05.2012
    Beiträge
    8.468
    Thanks
    509
    Thanked 4.504 Times in 1.979 Posts
    Die spark Box hat ja nichts mit der Box aus dem anderen Beitrag zu tun was sagt das log von der spark Box

    Gesendet von meinem SM-G935F mit Tapatalk

    Gehasst, Verdammt, Vergöttert
    Fragen gehören ins Forum nicht in meinem Postfach!
    >> Häufig gestellte Fragen <<


  2. #2
    Benutzer
    Registriert seit
    10.10.2014
    Beiträge
    33
    Thanks
    0
    Thanked 0 Times in 0 Posts
    So, habe es mit Teilen aus der Kruschtelkiste hinbekommen, ein Bootlog zu ziehen:

    Code:
    Board: STx7105-PDK  [32-bit mode]
    
    
    U-Boot 1.3.1 (Jun 19 2012 - 17:10:44) - stm23_0051 - YW_1.1.005 overclock
    
    DRAM:  256 MiB
    Panel: VFD
    NAND:  Bad block table found at page 262080, version 0x01
    Bad block table found at page 262016, version 0x01
    512 MiB
    SPI:  info: found S25FL016K (2MiB) device (page=256,erase=65536)
    warning: SPI device may be write-protected (status=0x9c)
    In:    serial
    Out:   serial
    Err:   serial
    Ident ic exist
    Ident ic get stb id
    IdentID : 0c 00 07 00 00 34 1b
    Hit ESC to stop autoboot:  0
    
    Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
       Image Name:   Linux-2.6.32.71_stm24_0217
       Image Type:   SuperH Linux Kernel Image (gzip compressed)
       Data Size:    2090743 Bytes =   2 MiB
       Load Address: 80801000
       Entry Point:  80802000
    ## Booting image at 80000000 ...
       Image Name:   Linux-2.6.32.71_stm24_0217
       Image Type:   SuperH Linux Kernel Image (gzip compressed)
       Data Size:    2090743 Bytes =   2 MiB
       Load Address: 80801000
       Entry Point:  80802000
       Verifying Checksum ... OK
       Uncompressing Kernel Image ... OK
    stmac_phy_get_addr(): id1 = 0xffff, id2 = 0xffff
    found phy at addres = 2
    stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
    stb_id = c0700341b
    
    Starting kernel console=ttyAS1,115200 rw root=/dev/mtdblock6 rootfstype=jffs2 init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 ip=172.100.100.249:172.100.100.174:172.100.100.174:255.255.0.0:Enigma2:eth0:off stmmaceth=msglvl:0,phyaddr:2,watchdog:5000 bigphysarea=6000 nwhwconf=device:eth0,hwaddr:30:00:07:00:34:1B Manufacture=Spark-Project STB_ID=0C:00:07:00:00:34:1B - 0x00000000 - 0 ...
    Genau da bleibt das ganze stehen und es passiert nichts mehr.

    Gruß


Berechtigungen

  • Neue Themen erstellen: Nein
  • Themen beantworten: Nein
  • Anhänge hochladen: Nein
  • Beiträge bearbeiten: Nein
  •