Seite 1 von 2 12 LetzteLetzte
Ergebnis 1 bis 10 von 16
  1. #1
    Moderator Avatar von morly
    Registriert seit
    15.07.2012
    Ort
    Österreich
    Beiträge
    6.684
    Thanks
    789
    Thanked 2.764 Times in 1.357 Posts

    SH4 - Stand der Dinge

    Hi Zusammen,
    SH4 ist arg "schief" - werde darum den Sammelthread hier eröffnen und euch am Laufenden halten.
    Antwortet hier im Thread um Bugs zu reporten.
    Ich teste und arbeite mit meiner UFS 913!
    Das nächste Image release ich, wenn ich es testfähig halte - nicht vorher!

    Hi guys,
    SH4 is kind of buggy thereefor this thread to collect bugs and inform you about the current state of fixing...
    Reply here to report your SH4 BUGS.
    I test and develop with my ufs913
    No release bofore I think it is worse a test...

    Thx for you support!

    Bugs:
    • Image bootet nicht (Dauerschleife) ... gefixt
    • StartWizard (Erstassi) erscheint nicht ... gefixt
    • OpenWebif funktioniert nicht .... gefixt
    • Permanente Untertitel ... gefixt
    • Falsche audio.elf bei IPBox ... gefixt
    • Leere "Information" ... gefixt
    • Fehler bei Standby ... gefixt
    • NetzwerkAssistent (Ethernet) ... gefixt
    • Overclock ... working
    • Kanalliste nach Installation ... gefixt
    • Plugins installieren ... gefixt
    • tiMote Screenshots ... gefixt
    • About Fenster ... added


    Nach Image: HDMU_17212_E2_git_614

    Bugs:
    • HDMU_17212_E2_1008g+se+_217_git_614 : falscher Kernel (uImage) ... gefixt
    • IPBoxen: Tuner 12V Bug ... gefixt (thx to ghani) ... gefixt
    • Falsche audio.elf bei IPBoxen ... gefixt
    • Menüeintrag: Project-ID version: enigma 2 (zweizeilig) ... gefixt
    • Fehlende Menüeinträge im Expertenmodus ... gefixt
    • audio.elf's aller Boxen anpassen ... gefixt
    • Crash beim SoftcamSetup ... gefixt
    • Crash bei Flashimage ... gefixt


    Nach Image: HDMU_17313_E2_git_617

    Bugs:
    • HDMU_17212_E2_1008g+se+_217_git_614 : Fehler im VideoWizard (Reboot) ...
    • Rote LED fehlt bei Aufnahme (UFS913) ...
    • ufs913: beim auswählen des streamings vom Handy aus(über timote 0.4.4) kommt es zu einem reboot
    • ErstAssi - Satellitenwahl - Reboot (konnte ich noch nicht nachstellen) ...
    • player 2 Bug ...
    • UFS912: ErstAssi startet nicht ...
    • ...
    "Every Setback is a Set Up for a Comeback"

  2. The Following 24 Users Say Thank You to morly For This Useful Post:



  3. #2
    Moderator Avatar von morly
    Registriert seit
    15.07.2012
    Ort
    Österreich
    Beiträge
    6.684
    Thanks
    789
    Thanked 2.764 Times in 1.357 Posts
    updated
    "Every Setback is a Set Up for a Comeback"

  4. The Following 7 Users Say Thank You to morly For This Useful Post:



  5. #3
    Moderator Avatar von morly
    Registriert seit
    15.07.2012
    Ort
    Österreich
    Beiträge
    6.684
    Thanks
    789
    Thanked 2.764 Times in 1.357 Posts
    updated
    "Every Setback is a Set Up for a Comeback"

  6. The Following 3 Users Say Thank You to morly For This Useful Post:



  7. #4
    Benutzer
    Registriert seit
    26.06.2012
    Beiträge
    79
    Thanks
    8
    Thanked 22 Times in 17 Posts

    Topf 17311_217_git_616

    Hi,
    danke morly, dass du dich um sh4 kümmerst.
    Der Topf bleibt bei LOAD MODULES stehen.
    Hier das log beim Startversuch:
    Code:
    ToFiÿ
    <<< Loader L23231>>>
    “ToFi"Z¿Š¿Z[!p
    
    Board: TF7700  [29-bit mode]
    
    
    
    U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043
    
    DRAM:  128 MiB
    NOR:     8 MiB
    In:    serial
    Out:   serial
    Err:   serial
    Hit any key to stop autoboot:  1  0 
    (Re)start USB...
    USB:   scanning bus for devices... 1 USB Device(s) found
           scanning bus for storage devices... 0 Storage Device(s) found
    ** Can't read from device 0 **
    
    ** Unable to use usb 0:1 for fatload **
    ## Booting image at 85000000 ...
    Bad Magic Number
    ## Booting image at 80060000 ...
       Image Name:   Linux-2.6.32.71_stm24_0217
       Image Type:   SuperH Linux Kernel Image (gzip compressed)
       Data Size:    1961528 Bytes =   1.9 MiB
       Load Address: 84001000
       Entry Point:  84002000
       Verifying Checksum ... OK
       Uncompressing Kernel Image ... OK
    
    Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:::255.255.255.0:tf7700:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:3e:9e:53:7d:9e - 0x00000000 - 0 ...
    
    
    INIT: version 2.88 booting
    
    init frontpanel
    fsck.jfs version 1.1.15, 04-Mar-2011
    processing started: 1/22/2018 15:43:12
    The current device is:  /dev/sda3
    
    The superblock does not describe a correct jfs file system.
    
    If device /dev/sda3 is valid and contains a jfs file system,
    then both the primary and secondary superblocks are corrupt
    and cannot be repaired, and fsck cannot continue.
    
    Otherwise, make sure the entered device /dev/sda3 is correct.
    
    [mountvirtfs] Mount /dev in tmpfs
    [mountvirtfs] Copying device nodes to /dev
    Starting portmap daemon....
    Loading autofs
    Starting autofs
    [mountall] Mounting local filesystems...
    Cleaning /tmp.
    Hostname: TOPF.
    init stmfb
    LOADING MODULES
    load firmware
    copLoadFile (file /boot/audio.elf)
    error ReadBytes
    copLoadFile (file /boot/video.elf)
    ustslave: Kernel Version: 24
    base_address 0x10000000
    init embx
    Hier noch das gesamte Log von der 2. Instalation bis Ende das Startvesuchs:
    Code:
    ToFiÿ <<< Loader L23231>>>
     “ToFi"Z¿Š¿Z[!p
     
    
     Board: TF7700  [29-bit mode]
     
    
     
    
     
    
     U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043
     
    
     DRAM:  128 MiB
     NOR:     8 MiB
     In:    serial
     Out:   serial
     Err:   serial
     Hit any key to stop autoboot:  1  0 
     (Re)start USB...
     USB:   scanning bus for devices... 2 USB Device(s) found
            scanning bus for storage devices... 1 Storage Device(s) found
     reading uImage
     ............................................................................................................................................................................................................................................................................................................................................................................................................................
     
    
     
    
     
    
     4224608 bytes read
     ## Booting image at 85000000 ...
        Image Name:   Linux-2.6.32.28_stm24_0207
        Image Type:   SuperH Linux Kernel Image (gzip compressed)
        Data Size:    4224544 Bytes =   4 MiB
        Load Address: 84001000
        Entry Point:  84002000
        Verifying Checksum ... OK
        Uncompressing Kernel Image ... OK
     
    
     Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:::255.255.255.0:tf7700:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:3e:9e:53:7d:9e - 0x00000000 - 0 ...
     
    
     115200
     speed 115200 baud;
     intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>;
     eol2 = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W;
     lnext = ^V; flush = ^O; min = 1; time = 0;
     -brkint ixoff -imaxbel
     -------------------------------------
     deploy.sh
     V0.10: Try several times to mount USB sticks if mount fails
     V0.09: Log installation to boot medium removed again because it caused problems
     V0.08: Log installation to boot medium
     V0.07: Do not install E2 if disk is not partitioned
                  and parameter partition is set to 0
     V0.06: Added EXT2 option for E2 and MINI partitions
     V0.05: Added JFS option for RECORD partition
     V0.04: Changed ini File format
     V0.03: Suppress meaningless tar errors during save settings
     V0.02: Format Mini partitions with Ext3 instead of Ext2
     V0.01: New parameter CREATEMINI and cleanup of KEEPSETTINGS
     -------------------------------------
     Mounting USB stick
     Specification for KEEP SETTINGS detected at line 67
     Specification for additional KEEP SETTINGS detected at line 88
     -------------------------------------
     partition: 0
     createmini: 0
     keepsettings: 0
     keepbootargs: 1
     usejfs: 1
     useext2e2: 0
     usbhdd: 0
     format: 1
     update: 1
     -------------------------------------
     Skipping partitioning of the disk
     OK, Disk already partitioned.
     Formatting HDD
     mke2fs 1.41.14 (22-Dec-2010)
     Filesystem label=MINI9
     OS type: Linux
     Block size=4096 (log=2)
     Fragment size=4096 (log=2)
     Stride=0 blocks, Stripe width=0 blocks
     131648 inodes, 526128 blocks
     26306 blocks (5.00%) reserved for the super user
     First data block=0
     Maximum filesystem blocks=541065216
     17 block groups
     32768 blocks per group, 32768 fragments per group
     7744 inodes per group
     Superblock backups stored on blocks: 
         32768, 98304, 163840, 229376, 294912
     
    
     Writing inode tables:  0/17 1/17 2/17 3/17 4/17 5/17 6/17 7/17 8/17 9/1710/1711/1712/1713/1714/1715/1716/17done                            
     Creating journal (16384 blocks): done
     Writing superblocks and filesystem accounting information: done
     
    
     This filesystem will be automatically checked every 24 mounts or
     180 days, whichever comes first.  Use tune2fs -c or -i to override.
     Setting up swapspace version 1, size = 271430144 bytes
     8+0 records in
     8+0 records out
     Installing root file system
     Flashing U-Boot settings
     186+1 records in
     186+1 records out
     Skipped flashing mtdblock2 on user request.
     Flashing kernel
     3831+1 records in
     3831+1 records out
     e2fsck 1.41.14 (22-Dec-2010)
     Pass 1: Checking inodes, blocks, and sizes
     Pass 2: Checking directory structure
     Pass 3: Checking directory connectivity
     Pass 4: Checking reference counts
     Pass 5: Checking group summary information
     MINI9: 5312/131648 files (7.0% non-contiguous), 54498/526128 blocks
     swapoff: /etc/fstab: No such file or directory
     
    
     The system is going down NOW
     
    
     Sending SIGTERM to all processe
     
    
     Sending SIGKILL to all processe
     
    
     Requesting system reboo
     ToFiÿ
     <<< Loader L23231>>>
     “ToFi"Z¿Š¿Z[!p
     
    
     Board: TF7700  [29-bit mode]
     
    
     
    
     
    
     U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043
     
    
     DRAM:  128 MiB
     NOR:     8 MiB
     In:    serial
     Out:   serial
     Err:   serial
     Hit any key to stop autoboot:  1  0 
     (Re)start USB...
     USB:   scanning bus for devices... 2 USB Device(s) found
            scanning bus for storage devices... 1 Storage Device(s) found
     reading uImage
     
    
     
    
     ** Unable to read "uImage" from usb 0:1 **
     ## Booting image at 85000000 ...
     Bad Magic Number
     ## Booting image at 80060000 ...
        Image Name:   Linux-2.6.32.71_stm24_0217
        Image Type:   SuperH Linux Kernel Image (gzip compressed)
        Data Size:    1961528 Bytes =   1.9 MiB
        Load Address: 84001000
        Entry Point:  84002000
        Verifying Checksum ... OK
        Uncompressing Kernel Image ... OK
     
    
     Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:::255.255.255.0:tf7700:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:3e:9e:53:7d:9e - 0x00000000 - 0 ...
     
    
     
    
     INIT: version 2.88 booting
     
    
     init frontpanel
     skip
     fsck.jfs version 1.1.15, 04-Mar-2011
     processing started: 1/22/2018 15:52:13
     
    
     Error: Cannot open device /dev/sda3
     
    
     Usage:  fsck.jfs [-afnpvV] [-j journal_device] [--omit_journal_replay] [--replay_journal_only] device
     
    
     Emergency help:
      -a                 Automatic repair.
      -f                 Force check even if file system is marked clean.
      -j journal_device  Specify external journal device.
      -n                 Check read only, make no changes to the file system.
      -p                 Automatic repair.
      -v                 Be verbose.
      -V                 Print version information only.
      --omit_journal_replay    Omit transaction log replay.
      --replay_journal_only    Only replay the transaction log.
     [mountvirtfs] Seems to be the first run - Making devices in /dev...
     [makedev] Starting makedev...
      CI-slot(s) : Yes
      Tuners     : 2
      HDMI CEC   : No
     [makedev] done.
     [mountvirtfs] Mount /dev in tmpfs
     [mountvirtfs] Copying device nodes to /dev
     Starting portmap daemon....
     Loading autofs
     Starting autofs
     [mountall] Mounting local filesystems...
     Cleaning /tmp /var/run /var/lock.
     Hostname: TOPF.
     init stmfb
     LOADING MODULES
     load firmware
     copLoadFile (file /boot/audio.elf)
     error ReadBytes
    
     copLoadFile (file /boot/video.elf)
     ustslave: Kernel Version: 24
     base_address 0x10000000
     init embx


  8. #5
    Moderator Avatar von morly
    Registriert seit
    15.07.2012
    Ort
    Österreich
    Beiträge
    6.684
    Thanks
    789
    Thanked 2.764 Times in 1.357 Posts
    hast du ein altes image?
    pack mal die alte audio.elf ins neue Image und teste nochmal
    "Every Setback is a Set Up for a Comeback"

  9. The Following User Says Thank You to morly For This Useful Post:



  10. #6
    Benutzer
    Registriert seit
    26.06.2012
    Beiträge
    79
    Thanks
    8
    Thanked 22 Times in 17 Posts
    Hab das mal probiert. Also mit 7zip einfach ins "rootfs.tar.gz\rootfs.tar\.\boot" rein kopiert. Danach hat 7zip neu gepackt. Ich hoffe das war so richtig.
    Die ist von meinem Backup (14258). Die Größe hat sich aber bis hin zu den Letzten des Jahres 2017 nicht verändert.
    Funktioniert hat das nicht:
    Code:
    ToFiÿ
    <<< Loader L23231>>>
    “ToFi"Z¿Š¿Z[!p
    
    Board: TF7700  [29-bit mode]
    
    
    
    U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043
    
    DRAM:  128 MiB
    NOR:     8 MiB
    In:    serial
    Out:   serial
    Err:   serial
    Hit any key to stop autoboot:  1  0 
    (Re)start USB...
    USB:   scanning bus for devices... 2 USB Device(s) found
           scanning bus for storage devices... 1 Storage Device(s) found
    reading uImage
    ............................................................................................................................................................................................................................................................................................................................................................................................................................
    
    
    
    4224608 bytes read
    ## Booting image at 85000000 ...
       Image Name:   Linux-2.6.32.28_stm24_0207
       Image Type:   SuperH Linux Kernel Image (gzip compressed)
       Data Size:    4224544 Bytes =   4 MiB
       Load Address: 84001000
       Entry Point:  84002000
       Verifying Checksum ... OK
       Uncompressing Kernel Image ... OK
    
    Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:::255.255.255.0:tf7700:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:3e:9e:53:7d:9e - 0x00000000 - 0 ...
    
    115200
    speed 115200 baud;
    intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>;
    eol2 = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W;
    lnext = ^V; flush = ^O; min = 1; time = 0;
    -brkint ixoff -imaxbel
    -------------------------------------
    deploy.sh
    V0.10: Try several times to mount USB sticks if mount fails
    V0.09: Log installation to boot medium removed again because it caused problems
    V0.08: Log installation to boot medium
    V0.07: Do not install E2 if disk is not partitioned
                 and parameter partition is set to 0
    V0.06: Added EXT2 option for E2 and MINI partitions
    V0.05: Added JFS option for RECORD partition
    V0.04: Changed ini File format
    V0.03: Suppress meaningless tar errors during save settings
    V0.02: Format Mini partitions with Ext3 instead of Ext2
    V0.01: New parameter CREATEMINI and cleanup of KEEPSETTINGS
    -------------------------------------
    Mounting USB stick
    Specification for KEEP SETTINGS detected at line 67
    Specification for additional KEEP SETTINGS detected at line 88
    -------------------------------------
    partition: 0
    createmini: 0
    keepsettings: 0
    keepbootargs: 1
    usejfs: 1
    useext2e2: 0
    usbhdd: 0
    format: 1
    update: 1
    -------------------------------------
    Skipping partitioning of the disk
    OK, Disk already partitioned.
    Formatting HDD
    mke2fs 1.41.14 (22-Dec-2010)
    Filesystem label=MINI9
    OS type: Linux
    Block size=4096 (log=2)
    Fragment size=4096 (log=2)
    Stride=0 blocks, Stripe width=0 blocks
    131648 inodes, 526128 blocks
    26306 blocks (5.00%) reserved for the super user
    First data block=0
    Maximum filesystem blocks=541065216
    17 block groups
    32768 blocks per group, 32768 fragments per group
    7744 inodes per group
    Superblock backups stored on blocks: 
        32768, 98304, 163840, 229376, 294912
    
    Writing inode tables:  0/17 1/17 2/17 3/17 4/17 5/17 6/17 7/17 8/17 9/1710/1711/1712/1713/1714/1715/1716/17done                            
    Creating journal (16384 blocks): done
    Writing superblocks and filesystem accounting information: done
    
    This filesystem will be automatically checked every 38 mounts or
    180 days, whichever comes first.  Use tune2fs -c or -i to override.
    Setting up swapspace version 1, size = 271430144 bytes
    8+0 records in
    8+0 records out
    Installing root file system
    tar: invalid tar header checksum
    Flashing U-Boot settings
    186+1 records in
    186+1 records out
    Skipped flashing mtdblock2 on user request.
    Flashing kernel
    3831+1 records in
    3831+1 records out
    e2fsck 1.41.14 (22-Dec-2010)
    Pass 1: Checking inodes, blocks, and sizes
    Pass 2: Checking directory structure
    Pass 3: Checking directory connectivity
    Pass 4: Checking reference counts
    Pass 5: Checking group summary information
    MINI9: 697/131648 files (7.5% non-contiguous), 30982/526128 blocks
    swapoff: /etc/fstab: No such file or directory
    
    The system is going down NOW
    
    Sending SIGTERM to all processe
    
    Sending SIGKILL to all processe
    
    Requesting system reboo
    ToFiÿ
    <<< Loader L23231>>>
    “ToFi"Z¿Š¿Z[!p
    
    Board: TF7700  [29-bit mode]
    
    
    U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043
    
    DRAM:  128 MiB
    NOR:     8 MiB
    In:    serial
    Out:   serial
    Err:   serial
    Hit any key to stop autoboot:  1  0 
    (Re)start USB...
    USB:   scanning bus for devices... 2 USB Device(s) found
           scanning bus for storage devices... 1 Storage Device(s) found
    reading uImage
    
    
    ** Unable to read "uImage" from usb 0:1 **
    ## Booting image at 85000000 ...
    Bad Magic Number
    ## Booting image at 80060000 ...
       Image Name:   Linux-2.6.32.71_stm24_0217
       Image Type:   SuperH Linux Kernel Image (gzip compressed)
       Data Size:    1961528 Bytes =   1.9 MiB
       Load Address: 84001000
       Entry Point:  84002000
       Verifying Checksum ... OK
       Uncompressing Kernel Image ... OK
    
    Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:::255.255.255.0:tf7700:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:3e:9e:53:7d:9e - 0x00000000 - 0 ...
    
    
    INIT: version 2.88 booting
    
    init frontpanel
    fsck.jfs: error while loading shared libraries: libuuid.so.1: cannot open shared object file: No such file or directory
    [mountvirtfs] Seems to be the first run - Making devices in /dev...
    [makedev] Starting makedev...
     CI-slot(s) : Yes
     Tuners     : 2
     HDMI CEC   : No
    [makedev] done.
    [mountvirtfs] Mount /dev in tmpfs
    [mountvirtfs] Copying device nodes to /dev
    Starting portmap daemon....
    Loading autofs
    Starting autofs
    /etc/init.d/autofs: line 56: /usr/sbin/automount: not found
    /etc/init.d/autofs: line 56: /usr/sbin/automount: not found
    [mountall] Mounting local filesystems...
    mkdir: can't create directory '/var/lock': No such file or directory
    mkdir: can't create directory '/var/lock/subsys': No such file or directory
    mkdir: can't create directory '/var/log': No such file or directory
    mkdir: can't create directory '/var/lib': No such file or directory
    mkdir: can't create directory '/var/lib/urandom': No such file or directory
    mkdir: can't create directory '/var/run': No such file or directory
    ln: /var/tmp: No such file or directory
    Cleaning /tmp.
    Hostname: TOPF.
    init stmfb
    Segmentation fault
    LOADING MODULES
    load firmware
    copLoadFile (file /boot/audio.elf)
    ustslave: Kernel Version: 24
    base_address 0x10400000
    copLoadFile (file /boot/video.elf)
    ustslave: Kernel Version: 24
    base_address 0x10000000
    init embx
    init AVS
    insmod: can't insert '/lib/modules/p2div64.ko': invalid module format
    insmod: can't insert '/lib/modules/pseudocard.ko': unknown symbol in module, or unknown parameter
    insmod: can't insert '/lib/modules/stm_monitor.ko': unknown symbol in module, or unknown parameter
    insmod: can't insert '/lib/modules/stmdvb.ko': unknown symbol in module, or unknown parameter
    insmod: can't insert '/lib/modules/player2.ko': unknown symbol in module, or unknown parameter
    insmod: can't insert '/lib/modules/sth264pp.ko': unknown symbol in module, or unknown parameter
    insmod: can't insert '/lib/modules/stmalloc.ko': unknown symbol in module, or unknown parameter
    insmod: can't insert '/lib/modules/platform.ko': invalid module format
    insmod: /lib/modules/smartcard.ko: module not found
    cat: write error: Input/output error
    /etc/init.d/rcS: line 667: /usr/sbin/inetd: not found
    showSinglePic /boot/bootlogo.mvi
    VIDEO_SET_FORMAT failed (Bad file descriptor)
    [mountall] Mounting local filesystems...
    Deconfiguring network interfaces... ifdown: interface lo not configured
    ifdown: interface eth0 not configured
    ifdown: interface eth1 not configured
    ifdown: interface wlan0 not configured
    done.
    Setting up IP spoofing protection: rp_filter.
    Configuring network interfaces... ip: RTNETLINK answers: File exists
    ifup: can't open '/var/run/ifstate.new': No such file or directory
    done.
    mkdir: can't create directory '/var/lock': No such file or directory
    mkdir: can't create directory '/var/lock/subsys': No such file or directory
    mkdir: can't create directory '/var/log': No such file or directory
    mkdir: can't create directory '/var/lib': No such file or directory
    mkdir: can't create directory '/var/lib/urandom': No such file or directory
    mkdir: can't create directory '/var/run': No such file or directory
    ln: /var/tmp: No such file or directory
    Cleaning.
    /usr/bin/amixer: error while loading shared libraries: libasound.so.2: cannot open shared object file: No such file or directory
    /etc/init.d/rcS: line 667: /usr/sbin/mount.sh: not found
    /usr/bin/amixer: error while loading shared libraries: libasound.so.2: cannot open shared object file: No such file or directory
    /usr/bin/amixer: error while loading shared libraries: libasound.so.2: cannot open shared object file: No such file or directory
    [set_was_timer_wakeup] error reading /etc/enigma2/timers.xml
    [set_was_timer_wakeup] no timer aktiv
    starting e2->
    /etc/init.d/rcS: line 667: /usr/local/bin/enigma2: not found
    e2 ended <- RTV:  127
    *
    
    INIT: Switching to runlevel: 6starting e2->
    
    
    
    INIT: Sending processes the TERM signal
    
    Sending all processes the TERM signal...done.
    Sending all processes the KILL signal...done.
    Deactivating swap...umount: tmpfs busy - remounted read-only
    done.
    Unmounting local filesystems...umount: tmpfs busy - remounted read-only
    done.
    Rebooting... ToFiÿ
    <<< Loader L23231>>>
    “ToFi"Z¿Š¿Z[!p
    
    Board: TF7700  [29-bit mode]
    
    
    
    U-Boot 1.3.1-gfeb9b4b7-dirty (Oct 23 2011 - 12:43:54) - stm23_0043
    
    DRAM:  128 MiB
    NOR:     8 MiB
    In:    serial
    Out:   serial
    Err:   serial
    Hit any key to stop autoboot:  1  0 
    (Re)start USB...
    USB:   scanning bus for devices... 2 USB Device(s) found
           scanning bus for storage devices... 1 Storage Device(s) found
    reading uImage
    
    
    ** Unable to read "uImage" from usb 0:1 **
    ## Booting image at 85000000 ...
    Bad Magic Number
    ## Booting image at 80060000 ...
       Image Name:   Linux-2.6.32.71_stm24_0217
       Image Type:   SuperH Linux Kernel Image (gzip compressed)
       Data Size:    1961528 Bytes =   1.9 MiB
       Load Address: 84001000
       Entry Point:  84002000
       Verifying Checksum ... OK
       Uncompressing Kernel Image ... OK
    
    Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:::255.255.255.0:tf7700:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:3e:9e:53:7d:9e - 0x00000000 - 0 ...
    
    
    INIT: version 2.88 booting
    
    init frontpanel
    fsck.jfs: error while loading shared libraries: libuuid.so.1: cannot open shared object file: No such file or directory
    [mountvirtfs] Mount /dev in tmpfs
    [mountvirtfs] Copying device nodes to /dev
    Starting portmap daemon....
    Loading autofs
    Starting autofs
    /etc/init.d/autofs: line 56: /usr/sbin/automount: not found
    /etc/init.d/autofs: line 56: /usr/sbin/automount: not found
    [mountall] Mounting local filesystems...
    mkdir: can't create directory '/var/lock': No such file or directory
    mkdir: can't create directory '/var/lock/subsys': No such file or directory
    mkdir: can't create directory '/var/log': No such file or directory
    mkdir: can't create directory '/var/lib': No such file or directory
    mkdir: can't create directory '/var/lib/urandom': No such file or directory
    mkdir: can't create directory '/var/run': No such file or directory
    ln: /var/tmp: No such file or directory
    Cleaning /tmp.
    Hostname: TOPF.
    init stmfb
    Segmentation fault
    LOADING MODULES
    load firmware
    copLoadFile (file /boot/audio.elf)
    ustslave: Kernel Version: 24
    base_address 0x10400000
    copLoadFile (file /boot/video.elf)
    ustslave: Kernel Version: 24
    base_address 0x10000000
    init embx
    init AVS
    insmod: can't insert '/lib/modules/p2div64.ko': invalid module format
    insmod: can't insert '/lib/modules/pseudocard.ko': unknown symbol in module, or unknown parameter
    insmod: can't insert '/lib/modules/stm_monitor.ko': unknown symbol in module, or unknown parameter


  11. #7
    Benutzer
    Registriert seit
    26.06.2012
    Beiträge
    79
    Thanks
    8
    Thanked 22 Times in 17 Posts

    Spark7162 17311_217_git_616

    Hi,
    bei der Triplex fehlt der Eintrag "SoftCam / CI" unter Einstellungen im Menü.
    Unter System fehlen:
    - "A/V-Einstellungen"
    - "Fernbedienung-Einstellungen"
    - "Skin"
    - "Testbilder"

    Wenn man versucht per Admintool drauf zuzugreifen, friert das Bild ein und nur Strom aus hilft weiter.
    Falls hierzu ein Log gewünscht wird, bitte ich um Nachricht, da ich für das serielle Log etwas Aufwand bei der Box habe.


  12. #8
    Moderator Avatar von morly
    Registriert seit
    15.07.2012
    Ort
    Österreich
    Beiträge
    6.684
    Thanks
    789
    Thanked 2.764 Times in 1.357 Posts
    updated
    "Every Setback is a Set Up for a Comeback"

  13. The Following 2 Users Say Thank You to morly For This Useful Post:



  14. #9
    Erfahrener Benutzer
    Registriert seit
    31.10.2013
    Beiträge
    221
    Thanks
    62
    Thanked 19 Times in 15 Posts
    @morly, was war eigentlich mit der Tuner los, also der 12V Bug. Gab dieseer Fehler immer 'Tune failed'? Wenn so, ist das auch bei der Spark behoben?


  15. #10
    Moderator Avatar von morly
    Registriert seit
    15.07.2012
    Ort
    Österreich
    Beiträge
    6.684
    Thanks
    789
    Thanked 2.764 Times in 1.357 Posts
    genauen Fehler kenn ich nicht, findest die Infos im letzten ipbox Thread

    Fix war nur für ipbox & co
    "Every Setback is a Set Up for a Comeback"


Berechtigungen

  • Neue Themen erstellen: Nein
  • Themen beantworten: Nein
  • Anhänge hochladen: Nein
  • Beiträge bearbeiten: Nein
  •