Audioniek Images: general info

[MToeppi]

was genau brauche ich?


OpenPli Sh4 ipk Dateien sind fast nicht zu finden.


Hab zwei ausprobiert, eine wurde installiert, die andere nicht.
Bei der Installierten wurde im Softcam Menu leider nichts angezeigt.

Gibt es einen einfacheren Lösungsweg Oscam aufzuspielen?


Fragen über Fragen...Sorry

[Saayacoolu]

Hi audioniek
thanks so much for the new image of tf 7700pvr hd have flash my receiver and have enjoy the new image with good picture and soft signal level,the problem with me now is one I can’t record giving massage NO HDD found or HDD notinitialized and two i ant connect to my WiFi.where can i correct to have my receiver perform well

[ainouna]

Hi audioniek
there is a solution for downloading plugins and emulators
while waiting for your feeds
if you accept I download it here

[Audioniek]

@Saayacoolu: As you have the image running, there is a hard disk available. First, be sure you followed the instructions or first time installation. as this requires editing the file Enigma_Installer.ini on the USB stick used for installation. On subsequent installations you can use the file unchanged. Please note the procedure will destroy any existing recordings on the hard disk. Second: check and possibly set the correct recording paths using the menu.
As for WiFi, the available drivers are all in the image but one must be activated by editing the file /etc/init.d/rcS. Find this section:

/bin/evremote2 110 10 &

stfbcontrol a 255

wlan=`cat /etc/enigma2/settings | grep systemoptions.wlan | cut -d "=" -f2`
if [ ! $wlan ] || [ ! -e $MODDIR/$wlan.ko ]; then
   echo "[rcS] No WLAN"
else
   insmod $MODDIR/$wlan.ko
   echo "[rcS] $wlan WLAN"
#   echo "$wlan WLAN" > /dev/vfd
#   sleep 3
fi

change the line beginning with wlan= to wlan=[drivername]. The possible driver names are: mt7601u, rt2870sta, rt3070sta, rt5370sta, rtl8188eu, rtl8192cu, rtl8192du, rtl8192eu and rtl871x. An example for the line would be wlan=rt2870sta. Which one you need depends on your wifi-stick. After changing rcS reboot the receiver. Wifi should now work. I will try to add a plugin selecting the wifi driver in the receivers' menu in an upcoming version.

@ainouna: offering plugins currently is not an option for me as I do not have the time to maintain them, do not have the ability to build them and do not have ability to (legally) host them. Sorry.

Regards,

Audioniek.

[Saayacoolu]

Hi Audioniek
as directed to go about my WiFi network don’t know what happened after finished writing it and placed back to position my deck refused to show pictur on my tv so I decided to reprogram it and during the process lights went off and when light came back powering my deck gives me L275 E02 on the panel where do I go next ,help needed here



Regards

[ainouna]

HI Audioniek
I propose a RUnigma feed
compatible with your audioniek image
with your permission
I download it on the site

[Saayacoolu]

Nothing heard of my problem,please expects come out to save my deck

[Audioniek]

First of all, I am not an instant answer service desk, so a little patience please. The most likely cause of the problem is that you edited the file with an editor that is not Linux compatible (did you see the warning on top?). This will screw up the installation.

I am not familiar ith the message L275 E02 on the display; it probably means the loader version and an error number. It that is true it is probably telling you it cannot find an image to start. Repeat the installation after verfying that the file Enigma_installer.ini has line endings LF not CRLF.

Audioniek.

[pop1234]

Audioniek
pls delete some PM
thx

[Audioniek]

Done.

Regards,

Audioniek.