Spark7162

[satstyler]

Hi : D

I'm looking a trying to compile my own image for a Spark7162 receiver using the SH4 Duckbox project.

When i run ./make.sh and select the following options 20 8 3 3 2 2 2 1 and doing a make yaud-enigma2-pli-nightly. It all compiles ok

I then go into /flash and run the spark.sh script to create the e2jffs2.img and uImage.

What i would like to know is before running the spark.sh script do i need to do anything else ? I copied good audio.elf and video.elf and its selected during build. Do i need to copy good /modules to the filesystem before compression or anything ?

Many Thanks

[DboxOldie]

You must do something with the devs, the script uses fakeroot and the devs are not with the right permission.

[JKM73]

bei SSC Treiber kann man keine Aufnahmen mehr anschauen kommt eine Fehlermeldung PAT nicht gefunden kein TUNER verfügbar als ob er die Sendung suchen würde anstatt abzuspielen.

Bin jetzt wieder auf deinen ersten zurück der läuft bei mir ohne Probleme bei dem funzen nach dem Kanalsuchlauf auch die PayTV Kanäle.

Gruß JKM73


Ups falscher Thread

[satstyler]

You must do something with the devs, the script uses fakeroot and the devs are not with the right permission.

Thanks ... so do you mean you have to change the permissions on the devs ? before using the script ? or would it just be as easy to do a mkfs.jffs2 -r release -o e2jffs2.img -e 0x20000 -pn on the release directory ?

[DboxOldie]

Oh, I just see the fakeroot isn´t there anymore. Well, then try it and look in /tmp/ROOT if the devs are right. I use another way, because I don´t build as root.

[satstyler]

Thanks i will check that out .... if you don't mind me asking what way do you use ?

[DboxOldie]

I´ve made me a tar file with the devs, and let it extract per sudo in the script into /tmp/ROOT/dev. So the script works fine and in /out is an flashable Image.

[satstyler]

ok understand ... Many Thanks i shall give this a try

[linch]

First think hello to all guys sorry for english but i not speak deutch.........i'm trying build an openpli for my amiko alien2 (spark7162) from duckbox
I compile with ubuntu 12.04 x86 i have read many documents and firmware is build.
I work in this way and all is done from root.
1- i start with options 20-8-3-3-1-1-1
2- as from wiki i put into /home/tdt/tdt/cvs/cdk/root/boot audio and video.elf that i thake from protriple-x e2 image with same kernel (first doubt are correct files ?? and how many files and with wich name must be there ??)
3- build end is ok (i must only cross-compile into toolchain dbus package)
the problems...
4- if i build e2jffs2.img and uImage from /spark dir with spark.sh script when i put my usb on alien2 after 3-4 minutes and after it have /load e2-300/boot-success nothing happens.
5- if i build e2jffs2.img with command "mkfs.jffs2 -r release -o e2jffs2.img -e 0x20000 -pn" and take uImage from /boot folder put usb on alien2 and after 3-4 minutes and after /load e2-300/boot-success the bootup stop on display message "wait...load" and nothing happens.
I read first here something about dev but sorry i not understand......if someone have suggestions and help is welcome.
Many thanks and best regards.

[DboxOldie]

Look in the folder /tmp/ROOT/dev on your build system if the devs are right. ( Not only simple empty textfiles )