+ Antworten
Seite 3 von 4 ErsteErste 1234 LetzteLetzte
Ergebnis 21 bis 30 von 33

Thema: Spark7162

  1. #21
    Neuer Benutzer
    Registriert seit
    27.08.2012
    Beiträge
    22
    Thanks
    10
    Thanked 0 Times in 0 Posts
    Tried to get a log via serial but no matter what image is installed it only gives the Kernel details and some other info as below;

    Board: STx7105-PDK [32-bit mode]




    U-Boot 1.3.1 (Jun 19 2012 - 17:10:44) - stm23_0051 - YW_1.1.005 overclock


    DRAM: 256 MiB
    Panel: VFD
    NAND: Bad block table found at page 262080, version 0x01
    Bad block table found at page 262016, version 0x01
    512 MiB
    SPI: info: found AT25DF161 (2MiB) device (page=256,erase=65536)
    warning: SPI device may be write-protected (status=0x0c)
    In: serial
    Out: serial
    Err: serial
    Ident ic exist
    Ident ic get stb id
    IdentID : 0c 00 0a 00 00 15 d3
    Hit ESC to stop autoboot: 0


    Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
    Image Name: Linux-2.6.32.28_stm24_0207
    Image Type: SuperH Linux Kernel Image (gzip compressed)
    Data Size: 2693637 Bytes = 2.6 MiB
    Load Address: 80801000
    Entry Point: 80802000
    ## Booting image at 80000000 ...
    Image Name: Linux-2.6.32.28_stm24_0207
    Image Type: SuperH Linux Kernel Image (gzip compressed)
    Data Size: 2693637 Bytes = 2.6 MiB
    Load Address: 80801000
    Entry Point: 80802000
    Verifying Checksum ... OK
    Uncompressing Kernel Image ... OK
    stmac_phy_get_addr(): id1 = 0xffff, id2 = 0xffff
    found phy at addres = 2
    stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
    stb_id = c0a0015d3


    Starting kernel console=ttyAS1,115200 rw root=/dev/mtdblock6 rootfstype=jffs2 init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 ip=172.100.100.249:172.100.100.174:172.100.100.174 :255.255.0.0:Enigma2:eth0:off stmmaceth=msglvl:0,phyaddr:2,watchdog:5000 bigphysarea=6000 nwhwconf=device:eth0,hwaddr00:0A:00D3 Manufacture=Spark-Project STB_ID=0C:00:0A:00:00D3 - 0x00000000 - 0 ...
    Geändert von satstyler (12.09.2012 um 22:12 Uhr)


  2. #22
    VIP
    Registriert seit
    13.05.2012
    Beiträge
    759
    Thanks
    35
    Thanked 345 Times in 243 Posts
    That´s the problem, it must be ttyAS0 !!! Therefore no more log comes from the kernel.

    console=ttyAS1


  3. #23
    Boardgründer/Administrator Avatar von bonkel
    Registriert seit
    03.05.2012
    Beiträge
    8.468
    Thanks
    509
    Thanked 4.504 Times in 1.979 Posts
    you must edit your bootargs to see more details...

    Gehasst, Verdammt, Vergöttert
    Fragen gehören ins Forum nicht in meinem Postfach!
    >> Häufig gestellte Fragen <<


  4. #24
    Neuer Benutzer
    Registriert seit
    27.08.2012
    Beiträge
    22
    Thanks
    10
    Thanked 0 Times in 0 Posts
    ah ok thanks will do that


  5. #25
    Neuer Benutzer
    Registriert seit
    31.08.2012
    Beiträge
    19
    Thanks
    4
    Thanked 3 Times in 2 Posts
    Zitat Zitat von satstyler Beitrag anzeigen
    Just tried to compile another image after updating the git ... the dev's do seem to be ok now after the move from fakeroot to sudo, but still have a finished image that fails to boot ... stays on 'load' on the VFD. Has anyone managed to build/compile and successfully install an image from this GIT ?
    Now git work great.....
    have you right video.elf and audio.elf files ??


  6. #26
    Neuer Benutzer
    Registriert seit
    27.08.2012
    Beiträge
    22
    Thanks
    10
    Thanked 0 Times in 0 Posts

    Spark7162

    Changed bootargs to ttyAS1 but still don't see any extra logs. Used audio.elf and video.elf from a working image so they should be ok. What do you use as your build environment ? Ubuntu , Fedora etc ? 32bit or 64 bit ?


  7. #27
    Boardgründer/Administrator Avatar von bonkel
    Registriert seit
    03.05.2012
    Beiträge
    8.468
    Thanks
    509
    Thanked 4.504 Times in 1.979 Posts
    ubuntu 32 and 64 bit

    Gehasst, Verdammt, Vergöttert
    Fragen gehören ins Forum nicht in meinem Postfach!
    >> Häufig gestellte Fragen <<


  8. #28
    VIP
    Registriert seit
    13.05.2012
    Beiträge
    759
    Thanks
    35
    Thanked 345 Times in 243 Posts
    Once more: ttyAS1 is wrong !!!! it must be ttyAS0 , because the linux-kernel uses this line.
    If you build the image from Git then it´s a debug image with the kernel config from Git and you will see the kernel messages.


  9. #29
    Neuer Benutzer
    Registriert seit
    27.08.2012
    Beiträge
    22
    Thanks
    10
    Thanked 0 Times in 0 Posts

    Spark7162

    My apologies .. I misread your post .. Will try again many thanks


  10. #30
    Neuer Benutzer
    Registriert seit
    27.08.2012
    Beiträge
    22
    Thanks
    10
    Thanked 0 Times in 0 Posts
    Hi All,

    Had a few problems with my serial cable so didn't have an opportunity to capture a log of failure. Missed the 1st part of the log due to not setting the scrollback properly ..but looks like a possible modules issue ?

    usbcore: registered new interface driver usbfsusbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    DMA: Registering DMA API.
    Switching to clocksource TMU1
    NET: Registered protocol family 2
    IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
    TCP established hash table entries: 8192 (order: 4, 65536 bytes)
    TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
    TCP: Hash tables configured (established 8192 bind 8192)
    TCP reno registered
    NET: Registered protocol family 1
    RPC: Registered udp transport module.
    RPC: Registered tcp transport module.
    Installing knfsd (copyright (C) 1996 okir@monad.swb.de)..
    Slow work thread pool: Starting up
    Slow work thread pool: Ready
    NTFS driver 2.1.29 [Flags: R/O].
    JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
    fuse init (API version 7.13)
    JFS: nTxBlock = 905, nTxLock = 7244
    msgmni has been set to 226
    io scheduler noop registered
    io scheduler anticipatory registered (default)
    lirc_dev: IR Remote Control driver registered, major 61
    lirc-stm: probe found data for platform device lirc-stm
    lirc-stm: STM LIRC plugin using IRQ 125 in IR mode
    lirc_dev: lirc_register_driver: sample_rate: 0
    STMicroelectronics LIRC driver initialized.
    STMicroelectronics ASC driver initialized
    stm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-asc
    stm-asc.1: ttyAS1 at MMIO 0xfd033000 (irq = 120) is a stm-asc
    loop: module loaded
    Davicom DM9161E: Registered new driver (0x0181b880)
    Davicom DM9161A: Registered new driver (0x0181b8a0)
    Davicom DM9131: Registered new driver (0x00181b80)
    RTL821x Gigabit Ethernet: Registered new driver (0x001cc912)
    STe100p: Registered new driver (0x1c040011)
    STe101p: Registered new driver (0x00061c50)
    Micrel KS8001 or KS8721: Registered new driver (0x0022161a)
    Micrel KSZ9021 Gigabit PHY: Registered new driver (0x00221611)
    Micrel KS8737: Registered new driver (0x00221720)
    Micrel KS8041: Registered new driver (0x00221510)
    Micrel KS8051: Registered new driver (0x00221550)
    STMMAC driver:
    platform registration...
    done!
    PMT module supported
    DWMAC1000 - user ID: 0x10, Synopsys ID: 0x33
    Enhanced descriptor structure
    PARSE CMDLINE: 00:00:00:00:00:00
    ETHADDR: 00:00:00:00:00:00
    no valid MAC address;please, use ifconfig or nwhwconfig!
    eth0 - (dev. name: stmmaceth - id: 0, IRQ #134
    IO base addr: 0xfd110000)
    STMMAC MII Bus: probed
    eth0: PHY ID 0007c0f1 at 2 IRQ 0 (0:02) active
    nwhw_config: (eth0) setting mac address: 30:00:0A:00C6
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    stm_usb_probe: usb_phy_clk clock not found for stm-usb.0
    stm-ehci stm-ehci.0: st-ehci
    stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
    stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00
    stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 1 port detected
    stm-ohci stm-ohci.0: stm-ohci
    stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
    stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 1 port detected
    stm_usb_probe: usb_phy_clk clock not found for stm-usb.1
    stm-ehci stm-ehci.1: st-ehci
    stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3
    stm-ehci stm-ehci.1: irq 143, io mem 0xfeaffe00
    stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 1 port detected
    stm-ohci stm-ohci.1: stm-ohci
    stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4
    stm-ohci stm-ohci.1: irq 142, io mem 0xfeaffc00
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 1 port detected
    Initializing USB Mass Storage driver...
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    mice: PS/2 mouse device common for all mice
    i2c /dev entries driver
    Linux video capture interface: v2.00
    sh_tmu: TMU0 kept as earlytimer
    sh_tmu: TMU1 kept as earlytimer
    STMicroelectronics - Coprocessors st231 Init
    st231.0 Coprocessor -------------------------------------------
    flags 0001 RAM start at 0xbf000000 size 0x00400000
    cop. addr 0x40000000
    Channels : Not defined
    IRQ : not used
    ---------------------------------------------------------------
    st231.1 Coprocessor -------------------------------------------
    flags 0001 RAM start at 0xbf400000 size 0x00400000
    cop. addr 0x40400000
    Channels : Not defined
    IRQ : not used
    ---------------------------------------------------------------
    DMA: Registering fdma_dmac.0 handler (16 channels).
    IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQs
    stm-fdma stm-fdma.0: firmware: using built-in firmware fdma_STx7105_0.elf
    DMA: Registering fdma_dmac.1 handler (16 channels).
    platform fdma_dmac.0: SLIM hw 0.0, FDMA fw 2.1
    IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQs
    stm-fdma stm-fdma.1: firmware: using built-in firmware fdma_STx7105_1.elf
    stm-rng hardware driver 1.0 configured
    platform fdma_dmac.1: SLIM hw 0.0, FDMA fw 2.5
    Advanced Linux Sound Architecture Driver Version 1.0.21.
    ALSA device list:
    #0: STMicroelectronics STx7105 cut 4 SOC audio subsystem
    TCP cubic registered
    NET: Registered protocol family 17
    NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 512MiB 3,3V 8-bit)
    stm-nand-flex: Using boot partition name [uboot] (from kernel config)
    cmdlinepart partition parsing not available
    Creating 7 MTD partitions on "stm-nand-flex.0":
    0x000000000000-0x000000100000 : "uboot"
    0x000000100000-0x000000b00000 : "Spark kernel"
    0x000000b00000-0x000001200000 : "Reserve0"
    0x000001200000-0x000001400000 : "Reserve1"
    0x000001400000-0x000018000000 : "Spark Userfs"
    0x000018000000-0x000018800000 : "E2 kernel"
    0x000018800000-0x00001ff00000 : "E2 Userfs"
    stm-nand-flex: Found BOOT parition[uboot], updating ECC paramters
    boot-ECC 0x00000000->0x00100000
    stmmac: Rx Checksum Offload Engine supported
    TX Checksum insertion supported
    IP-Config: Complete:
    device=eth0, addr=172.100.100.249, mask=255.255.0.0, gw=172.100.100.174,
    host=Enigma2, domain=, nis-domain=(none),
    bootserver=172.100.100.174, rootserver=172.100.100.174, rootpath=
    Empty flash at 0x0229c170 ends at 0x0229c800
    VFS: Mounted root (jffs2 filesystem) on device 31:6.
    Freeing unused kernel memory: 132k freed
    INIT: version 2.86 booting
    PHY: 0:02 - Link is Up - 100/Full
    init frontpanel
    Fulan front panel driver
    VfdType = 2
    CpuType = 2
    DisplayInfo = 1
    scankeyNum = 8
    swMajorVersion = 1
    swSubVersion = 10
    input: fulan front panel buttons as /devices/virtual/input/input0
    [simu_button] initializing ...
    [simu_button] allocating and registering button device
    input: TDT RC event driver as /devices/virtual/input/input1
    insmod: can't insert '/lib/modules/encrypt.ko': No such file or directory
    Mount /dev in tmpfs
    Copying device nodes to /dev
    Starting portmap daemon....
    Loading autofs
    Starting autofs
    Starting DEBUG Interface
    Mounting local filesystems...
    mount: mounting /dev/sda1 on /hdd failed: No such device or address
    Cleaning /tmprmdir: './autoiagxTS': Device or resource busy
    rmdir: './autoMfEZww': No such file or directory
    find: ./autoW4nCuT: No such file or directory
    find: ./autoGPTxPw: No such file or directory
    .
    Hostname: spark7162.
    starting telnetd
    init stmfb
    stmcore-display: using HDMI hotplug
    stmcore-display: STi7105 display: probed
    device probe found 2 display pipelines
    requesting frm: 'component.fw', c11dd764/875c7c50
    stm-awg: firmware: requesting component.fw
    frm 'component.fw' successfully loaded
    requesting frm: 'fdvo0.fw', c11dd764/875c7fd0
    stm-awg: firmware: requesting fdvo0.fw
    loading frm: 'fdvo0.fw' failed: -2
    stmfb: fb0 parameters = "1280x720-32@50:15mal:yuv:yuv"
    stmfb: fb1 parameters = "<NULL>"
    LOADING MODULES
    load a firmware
    copLoadFile (file /boot/audio.elf)
    ustslave: Kernel Version: 24
    base_address 0x40400000
    seeking to d0000000
    seeking to d0005f00
    seeking to d0012320
    seeking to d001aa20
    seeking to d0173100
    seeking to d0173138
    seeking to d0173170
    seeking to d01b9058
    seeking to d01b9060
    seeking to d01b9068
    seeking to d01b9070
    seeking to d01d0920
    seeking to d01d0a00
    load v firmware
    copLoadFile (file /boot/video.elf)
    ustslave: Kernel Version: 24
    base_address 0x40000000
    seeking to d0000000
    seeking to d004e020
    seeking to d00f8378
    seeking to d00f83b0
    seeking to d00f83e8
    seeking to d010ce98
    seeking to d010cea4
    seeking to d010ceb0
    seeking to d012ed90
    seeking to d012cd74
    seeking to d012ee00
    init embx



Ähnliche Themen

  1. [spark] spark7162
    Von nahoul im Forum Beta Enigma2 Bereich für alle SH4 STB
    Antworten: 4
    Letzter Beitrag: 23.01.2013, 09:20
  2. Spark oder Spark7162?
    Von rurotil im Forum Anfänger/Newbie
    Antworten: 2
    Letzter Beitrag: 08.12.2012, 17:04
  3. [spark] HDMU Spark7162
    Von haythemzidi im Forum Beta Enigma2 Bereich für alle SH4 STB
    Antworten: 1
    Letzter Beitrag: 13.11.2012, 21:18

Berechtigungen

  • Neue Themen erstellen: Ja
  • Themen beantworten: Ja
  • Anhänge hochladen: Ja
  • Beiträge bearbeiten: Ja
  •