HDMU_272_E2_ufs912_209_git_4044_nodebug_USB.tar

[bonkel]

wer hat denn das gebaut und wie?^^

[Bretterknaller]

ks v4 Bootet nicht

usb 1-1.3: USB disconnect, address 3\0x00\0x00


Board: STx7111-Mboard (MB618) [32-bit mode]




U-Boot 1.3.1 (Nov 30 2009 - 11:46:12) - stm23-2008-06-03


DRAM: 256 MB
NOR: 4 MB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Serial 3 Intialized
buad = 19200, p2 val = 1109, t = c9, buadrate = 1
buad = 19200, p2 val = 1109, t = c9, buadrate = 3ee
VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD using PIC
Test Class : GetInstance()
Test Class : GetInstance()
RawBuffer.cpp at RawBuffer ,29
FD = 0
Test Class : GetInstance()
SWRecoveryHandler.cpp at Recover ,56
No Recovery Needed
End of testCpp
Hit any key to stop autoboot: 0


Loading from nand0, offset 0x0
Image Name: Linux-2.6.32.46_stm24_0209
Created: 2012-05-11 1958 UTC
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2156068 Bytes = 2.1 MB
Load Address: 80801000
Entry Point: 80802000
Original bootargs = console=ttyAS0,115200 root=/dev/mtdblock4 rw rootfstype=jffs2 init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1
ethaddr = 000:55:0E:4EB


new Params = console=ttyAS0,115200 root=/dev/mtdblock4 rw rootfstype=jffs2 init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 stmmaceth=ethaddr:000:55:0E:4EB


## Booting image at 84000000 ...
Image Name: Linux-2.6.32.46_stm24_0209
Created: 2012-05-11 1958 UTC
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2156068 Bytes = 2.1 MB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... OK
Uncompressing Kernel Image ... START = 539204
END = 36611
OK


Starting kernel console=ttyAS0,115200 root=/dev/mtdblock4 rw rootfstype=jffs2 init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 stmmaceth=ethaddr:000:55:0E:4EB
- 0x00000000 - 0 ...


Linux version 2.6.32.46_stm24_0209 (root@kleinerschelm-MS-7640) (gcc version 4.5.2 20110124 (STMicroelectronics/Linux Base 4.5.2-78) (GCC) ) #1 PREEMPT Fri May 11 2157 CEST 2012
Boot params:
... MOUNT_ROOT_RDONLY - 00000001
... RAMDISK_FLAGS - 00000000
... ORIG_ROOT_DEV - 00000200
... LOADER_TYPE - 00000000
... INITRD_START - 00000000
... INITRD_SIZE - 00000000
Booting machvec: STx7111 Mboard (Kathrein UFS-912)
Node 0: start_pfn = 0x40000, low = 0x50000
Zone PFN ranges:
Normal 0x00040000 -> 0x00050000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00040000 -> 0x00050000
STMicroelectronics STx7111 Mboard initialisation
STx7111 version 3.x
bpa2: partition 'bigphysarea' created at 0x48000000, size 32768 kB (0x02000000 B)
bpa2: partition 'LMI_IO' created at 0x4a000000, size 98304 kB (0x06000000 B)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyAS0,115200 root=/dev/mtdblock4 rw rootfstype=jffs2 init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 stmmaceth=ethaddr:000:55:0E:4EB


PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
PVR=04909200 CVR=60880000 PRR=00009a10
I-cache : n_ways=2 n_sets=512 way_incr=16384
I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Memory: 116736k/262144k available (2595k kernel code, 990k data, 100k init)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:500
Failed mb618 EPLD test (off 04, res 40)
Failed to enable clk CLKA_REF, ignoring
Failed to enable clk CLKA_PLL0LS, ignoring
console [ttyAS0] enabled
sh_tmu: TMU0 used for clock events
sh_tmu: TMU0 used for periodic clock events
sh_tmu: TMU1 used as clock source
Calibrating delay loop... 448.51 BogoMIPS (lpj=897024)
Mount-cache hash table entries: 512
CPU: STx7111
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
DMA: Registering DMA API.
Switching to clocksource TMU1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Slow work thread pool: Starting up
Slow work thread pool: Ready
NTFS driver 2.1.29 [Flags: R/O].
JFFS2 version 2.2. (NAND) (SUMMARY) \0xc2\0xa9 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
JFS: nTxBlock = 912, nTxLock = 7301
msgmni has been set to 228
io scheduler noop registered
io scheduler anticipatory registered (default)
STMicroelectronics ASC driver initialized
stm-asc.0: ttyAS0 at MMIO 0xfd031000 (irq = 122) is a stm-asc
loop: module loaded
physmap platform flash device: 00400000 at 00000000
CFI MFR = c2 DEV = 227e
devsize = 400000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 2 MTD partitions on "physmap-flash":
0x000000000000-0x000000080000 : "NOR U-BOOT : 0xA000.0000-0xA007.FFFF (512KB)"
0x000000080000-0x000000400000 : "NOR R00T : 0xA008.0000-0xA03F.FFFF (3,5MB)"
stm-nand-emi: Configuring EMI Bank 1 for NAND access
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
cmdlinepart partition parsing not available
Creating 4 MTD partitions on "stm-nand-emi.0":
0x000000000000-0x000000400000 : "NAND KERNEL : 0x0000.0000-0x003F.FFFF ( 4MB)"
0x000000400000-0x000000c00000 : "NAND FW : 0x0040.0000-0x00BF.FFFF ( 8MB)"
0x000000c00000-0x000004c00000 : "NAND ROOT : 0x00C0.0000-0x04BF.FFFF ( 64MB)"
0x000004c00000-0x000008000000 : "NAND DATA : 0x04C0.0000-0x07FF.FFFF ( 52MB)"
STMMAC driver:
\0x09platform registration...
\0x09done!
\0x09PMT module supported
\0x09Enhanced descriptor structure
PARSE CMDLINE: 000:55:0E:4EB
ETHADDR: 000:55:0E:4EB
\0x09eth0 - (dev. name: stmmaceth - id: -1, IRQ #133
\0x09IO base addr: 0xfd110000)
STMMAC MII Bus: probed
eth0: PHY ID 00008201 at 0 IRQ 0 (0:00) active
eth0: PHY ID 00008201 at 1 IRQ 0 (0:01)
eth0: PHY ID 00008201 at 2 IRQ 0 (0:02)
eth0: PHY ID 00008201 at 3 IRQ 0 (0:03)
eth0: PHY ID 00008201 at 4 IRQ 0 (0:04)
eth0: PHY ID 00008201 at 5 IRQ 0 (0:05)
eth0: PHY ID 00008201 at 6 IRQ 0 (0:06)
eth0: PHY ID 00008201 at 7 IRQ 0 (0:07)
eth0: PHY ID 00008201 at 8 IRQ 0 (0:08)
eth0: PHY ID 00008201 at 9 IRQ 0 (0:09)
eth0: PHY ID 00008201 at 10 IRQ 0 (0:0a)
eth0: PHY ID 00008201 at 11 IRQ 0 (0:0b)
eth0: PHY ID 00008201 at 12 IRQ 0 (0:0c)
eth0: PHY ID 00008201 at 13 IRQ 0 (0:0d)
eth0: PHY ID 00008201 at 14 IRQ 0 (0:0e)
eth0: PHY ID 00008201 at 15 IRQ 0 (0:0f)
eth0: PHY ID 00008201 at 16 IRQ 0 (0:10)
eth0: PHY ID 00008201 at 17 IRQ 0 (0:11)
eth0: PHY ID 00008201 at 18 IRQ 0 (0:12)
eth0: PHY ID 00008201 at 19 IRQ 0 (0:13)
eth0: PHY ID 00008201 at 20 IRQ 0 (0:14)
eth0: PHY ID 00008201 at 21 IRQ 0 (0:15)
eth0: PHY ID 00008201 at 22 IRQ 0 (0:16)
eth0: PHY ID 00008201 at 23 IRQ 0 (0:17)
eth0: PHY ID 00008201 at 24 IRQ 0 (0:18)
eth0: PHY ID 00008201 at 25 IRQ 0 (0:19)
eth0: PHY ID 00008201 at 26 IRQ 0 (0:1a)
eth0: PHY ID 00008201 at 27 IRQ 0 (0:1b)
eth0: PHY ID 00008201 at 28 IRQ 0 (0:1c)
eth0: PHY ID 00008201 at 29 IRQ 0 (0:1d)
eth0: PHY ID 00008201 at 30 IRQ 0 (0:1e)
eth0: PHY ID 00008201 at 31 IRQ 0 (0:1f)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
stm-ehci stm-ehci.0: st-ehci
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: stm-ohci
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Linux video capture interface: v2.00
sh_tmu: TMU0 kept as earlytimer
sh_tmu: TMU1 kept as earlytimer
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
STMicroelectronics - Coprocessors st231 Init
st231.0 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xbf000000 size 0x00400000
cop. addr 0x40000000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
st231.1 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xbf400000 size 0x00400000
cop. addr 0x40400000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
DMA: Registering fdma_dmac.0 handler (16 channels).
IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma.0: firmware: using built-in firmware fdma_STx7111_0.elf
DMA: Registering fdma_dmac.1 handler (16 channels).
platform fdma_dmac.0: SLIM hw 0.0, FDMA fw 2.1
IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma.1: firmware: using built-in firmware fdma_STx7111_1.elf
platform fdma_dmac.1: SLIM hw 0.0, FDMA fw 2.5
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
#0: STMicroelectronics STx7111 cut 3.x SOC audio subsystem
TCP cubic registered
NET: Registered protocol family 17
usb 1-1: new high speed USB device using stm-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.4: new high speed USB device using stm-ehci and address 3
usb 1-1.4: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
VFS: Mounted root (jffs2 filesystem) on device 31:4.
Freeing unused kernel memory: 100k freed
Kathrein UFS912 VFD/MICOM module initializing
0x0d
[simu_button] initializing ...
[simu_button] allocating and registering button device
input: TDT RC event driver as /devices/virtual/input/input0
stmcore-display: using HDMI hotplug
stmcore-display: STi7111 display probed
device probe found 2 display pipelines
requesting frm: 'component.fw', c15d81bc/87027110
stm-awg: firmware: requesting component.fw
frm 'component.fw' successfully loaded
requesting frm: 'fdvo0.fw', c15d81bc/87027490
stm-awg: firmware: requesting fdvo0.fw
loading frm: 'fdvo0.fw' failed: -2
stmfb: fb0 parameters = "1280x720-32@50:15m:10mal:yuv:yuv;#"
trying to alloc 10485760 bytes (align: 0000, still needed: 10485760) from 'gfx-memory' for GFX0 auxmem
success: base: 4a000000, still needed: 0
stmfb: Starting HDMI Output hdmi = 870a0000
scsi 0:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] Attached SCSI removable disk
stmfb: fb1 parameters = "720x576-16@50:1mal:cvbs;"

[Bretterknaller]

Bei ks v3 selbe log

[Anskar]

Was ist "ks v4 Bootet nicht" und "ks v3 Bootet nicht" ?
MfG

[Bretterknaller]

kleiner schelm (ks) hat 2 Images gebaut für Flash.Bin halt schreibfaul :-D

[KleinerSchelm]

ist das mit den KS images jetzt besser ? also ein stück weiter ?

[Bretterknaller]

Würde sagen das er noch früher hängen bleibt also bei stmfb und wir noch nicht mal zum laden der Firmenware kommen.

[bonkel]

was ist mit dem neuen ??^^

[quetschwalze]

Die bootet leider bei mir auch nicht...
Entweder die Katrein stürzt beim entpacken mit DuckBA ab oder Box bootet von der SDkarte nicht mehr.

[bonkel]

ich meint auch das flashimage ^^