Hallo, guten Tag,

bin neu im Forum und sende erst einmal einen Gruß an alle Mitglieder der Community!

Ich hätte da mal eine Frage an die Spezialisten. Habe hier eine Rebox RE-8000HD die gegenwärtig ganz gut mit dem DontCryAAF läuft. Jetzt wollte ich mich aber einmal nach etwas neuem und in Weiterentwicklung befindlichem umsehen und bin dabei auf HDMU gestoßen. Leider bekomme ich das Image aber nicht zum laufen.

Das HDBOX Image müsste für mich doch grundsätzlich das richtige sein oder?

Wenn ich keine Festplatte an eSata habe bleibt der Bootvorgang bei "Booting.." hängen:

Code:
Board: STb7200-HDBOX  [29-bit mode]

U-Boot 1.3.1 (Apr 28 2010 - 15:01:04) - stm23-0032
---created by TDT for general purpose---

DRAM:  128 MB
Flash:   32 MB
In:    serial
Out:   serial
Err:   serial
Frontpanel got PowerOn reset...
init Frontpanel... done, AV7000
Hit any key to stop autoboot:  1  0 
bootmenu_timeout:3000,default:3
add entry:0 - ---Flash---
add entry:1 - --USB1 P1--
add entry:2 - --USB1 P2--
add entry:3 - --USB1 P3--
add entry:4 - --USB1 P4--
add entry:5 - --USB2 P1--
add entry:6 - --USB2 P2--
add entry:7 - --USB2 P3--
add entry:8 - --USB2 P4--
add entry:9 - --USB 112--
entering bootmenu - default:3 - --USB1 P3--
selected: --USB1 P2--
USB:   scanning bus for devices... 3 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage2

** Unable to read "/uImage2" from usb 0:1 **
loading from usb 0:2

1898081 bytes read
## Booting image at a5000000 ...
   Image Name:   Linux-2.6.32.61_stm24_0215
   Image Type:   SuperH Linux Kernel Image (gzip compressed)
   Data Size:    1898017 Bytes =  1.8 MB
   Load Address: 84001000
   Entry Point:  84002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel console=ttyAS1,115200 nwhwconf=device:eth0,hwaddr:00:1E:B8:01:3C:0A ip=192.168.178.28::192.168.178.1:255.255.255.0:Twin:eth0:off root=/dev/sdb2 rw mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=5 init=/bin/dev - 0x00000000 - 0 ...

Wenn ich eine Festplatte an eSata habe bleibt der Bootvorgang bei "T.-Ducktales" hängen:

Code:
Board: STb7200-HDBOX  [29-bit mode]

U-Boot 1.3.1 (Apr 28 2010 - 15:01:04) - stm23-0032
---created by TDT for general purpose---

DRAM:  128 MB
Flash:   32 MB
In:    serial
Out:   serial
Err:   serial
Frontpanel got PowerOn reset...
init Frontpanel... done, AV7000
Hit any key to stop autoboot:  1  0 
bootmenu_timeout:3000,default:3
add entry:0 - ---Flash---
add entry:1 - --USB1 P1--
add entry:2 - --USB1 P2--
add entry:3 - --USB1 P3--
add entry:4 - --USB1 P4--
add entry:5 - --USB2 P1--
add entry:6 - --USB2 P2--
add entry:7 - --USB2 P3--
add entry:8 - --USB2 P4--
add entry:9 - --USB 112--
entering bootmenu - default:3 - --USB1 P3--
selected: --USB1 P2--
USB:   scanning bus for devices... 3 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage2

** Unable to read "/uImage2" from usb 0:1 **
loading from usb 0:2

1898081 bytes read
## Booting image at a5000000 ...
   Image Name:   Linux-2.6.32.61_stm24_0215
   Image Type:   SuperH Linux Kernel Image (gzip compressed)
   Data Size:    1898017 Bytes =  1.8 MB
   Load Address: 84001000
   Entry Point:  84002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel console=ttyAS1,115200 nwhwconf=device:eth0,hwaddr:00:1E:B8:01:3C:0A ip=192.168.178.28::192.168.178.1:255.255.255.0:Twin:eth0:off root=/dev/sdb2 rw mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=5 init=/bin/dev - 0x00000000 - 0 ...
Ich kann mich auch noch dunkel erinnern, dass ich bei irgendeinem Image einmal eine leere .hdd Datei erstellen und irgendwo einfügen musste, damit es bootet.

Jetzt kann ich aus dem log leider nicht lesen, woran es liegen könnte.

Habt ihr eine Idee?