which image do you try to install?
I see only a P207 Image, try an other Image, p209 for IP900 or p211 for IP910
I have been able to load pkt e2 p211 image I will get it set up then I assume I can install 2 other images to usb1 & usb2 to see which one I like best I would like to get my external e-data hdd working if possible along with scart had. I may be able to use my 500gb usb drive to be partitioned for images and recordings?
Thanks for the help
H
Disk /dev/sda: 500.0 GB, 500074283008 bytes
255 heads, 63 sectors/track, 60797 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 32 257008+ 83 Linux
/dev/sda2 33 60797 488094862+ 83 Linux
[SifTeam]$
ok sorry to be a nuisance but i think my best option is to partition my 500gb usb hdd and use it to have several images on and also act as a hdd for recordings.
i am having a bit of trouble formatting it maybe you could give me these steps then i should be able to partition and load images as before on 16gb usb stick.
this is the mount info
SifTeam]$ mount
rootfs on / type rootfs (rw)
/dev/root on / type squashfs (ro)
none on /tmp type tmpfs (rw)
none on /dev type tmpfs (rw)
none on /mnt type tmpfs (rw)
/dev/mtdblock4 on /var type jffs2 (rw)
none on /tmp/mqueue type mqueue (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
tmpfs on /dev/shm type tmpfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
/dev/sda2 on /var/media type ext3 (rw,data=writeback)
[SifTeam]$
thanks
h
thanks i will try this
fdisk /dev/sda
delete 2
delete 1
n for create new part,
p primary
1
start 1
stop 60647
n
p
2
enter
60697
n
p
3
enter
60747
n
p
4
enter
enter
w write to exit
reboot
mkfs.ext2 -L RECORD /dev/sda1
mkfs.ext2 -L MINI2 -I128 -b4096 /dev/sda2
mkfs.ext2 -L MINI3 -I128 -b4096 /dev/sda3
mkfs.ext2 -L MINI4 -I128 -b4096 /dev/sda4
reboot
ftp image to one MINI Part(2,3 or4)
cd /mnt...
tar xvzf *.*
Code:fw_setenv menu_1 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:2 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda2 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA2-USB;boot' fw_setenv menu_2 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:3 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda3 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA3-USB;boot' fw_setenv menu_3 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:4 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda4 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA4-USB;boot'