+ Antworten
Ergebnis 1 bis 4 von 4
  1. #1
    Neuer Benutzer
    Registriert seit
    27.08.2012
    Beiträge
    22
    Thanks
    10
    Thanked 0 Times in 0 Posts

    Image hangs on booting

    Guten Morgen

    I have an issue at present ... image compiles all ok but when i install it and boot it hangs on boot ....
    As i say the image compiles ok using Spark7162 and 0211

    The log is as follows;

    Code:
    Board: STx7105-PDK  [32-bit mode]
    
    
    U-Boot 1.3.1 (Jun 19 2012 - 17:10:44) - stm23_0051 - YW_1.1.005 overclock
    
    DRAM:  256 MiB
    Panel: VFD
    NAND:  Bad block table found at page 262080, version 0x01
    Bad block table found at page 262016, version 0x01
    512 MiB
    SPI:  info: found AT25DF161 (2MiB) device (page=256,erase=65536)
    warning: SPI device may be write-protected (status=0x0c)
    In:    serial
    Out:   serial
    Err:   serial
    Ident ic exist
    Ident ic get stb id
    IdentID : 0c 00 0a 00 00 15 c6
    Hit ESC to stop autoboot:  0
    
    Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
       Image Name:   Linux-2.6.32.59_stm24_0211
       Image Type:   SuperH Linux Kernel Image (gzip compressed)
       Data Size:    2565491 Bytes =   2.4 MiB
       Load Address: 80801000
       Entry Point:  80802000
    ## Booting image at 80000000 ...
       Image Name:   Linux-2.6.32.59_stm24_0211
       Image Type:   SuperH Linux Kernel Image (gzip compressed)
       Data Size:    2565491 Bytes =   2.4 MiB
       Load Address: 80801000
       Entry Point:  80802000
       Verifying Checksum ... OK
       Uncompressing Kernel Image ... OK
    stmac_phy_get_addr(): id1 = 0xffff, id2 = 0xffff
    found phy at addres = 2
    stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
    stb_id = c0a0015c6
    
    Starting kernel console=ttyAS0,115200 rw root=/dev/mtdblock6 rootfstype=jffs2 init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 ip=172.100.100.249:172.100.100.174:172.100.100.174:255.255.0.0:Enigma2:eth0:off stmmaceth=msglvl:0,phyaddr:2,watchdog:5000 bigphysarea=6000 nwhwconf=device:eth0,hwaddr:30:00:0A:00:15:C6 Manufacture=Spark-Project STB_ID=0C:00:0A:00:00:15:C6 - 0x00000000 - 0 ...
    
    Linux version 2.6.32.59_stm24_0211 (user@ubuntu) (gcc version 4.5.2 20110124 (STMicroelectronics/Linux Base 4.5.2-78) (GCC) ) #1 PREEMPT Thu Nov 15 15:26:12 EST 2012
    Boot params:
    ... MOUNT_ROOT_RDONLY - 00000001
    ... RAMDISK_FLAGS     - 00000000
    ... ORIG_ROOT_DEV     - 00000200
    ... LOADER_TYPE       - 00000000
    ... INITRD_START      - 00000000
    ... INITRD_SIZE       - 00000000
    Booting machvec: hdk7105
    Node 0: start_pfn = 0x40000, low = 0x50000
    Zone PFN ranges:
      Normal   0x00040000 -> 0x00050000
    Movable zone start PFN for each node
    early_node_map[1] active PFN ranges
        0: 0x00040000 -> 0x00050000
    STMicroelectronics HDK7105 board initialisation
    STx7105 version 4.x
    Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
    Kernel command line: console=ttyAS0,115200 rw root=/dev/mtdblock6 rootfstype=jffs2 init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 ip=172.100.100.249:172.100.100.174:172.100.100.174:255.255.0.0:Enigma2:eth0:off stmmaceth=msglvl:0,phyaddr:2,watchdog:5000 bigphysarea=6000 nwhwconf=device:eth0,hwaddr:30:00:0A:00:15:C6 Manufacture=Spark-Project STB_ID=0C:00:0A:00:00:15:C6
    bpa2: partition 'bigphysarea' created at 0x40e95000, size 24000 kB (0x01770000 B)
    PID hash table entries: 1024 (order: 0, 4096 bytes)
    Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    PVR=04909200 CVR=60880000 PRR=00009e40
    I-cache : n_ways=2 n_sets=512 way_incr=16384
    I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
    D-cache : n_ways=2 n_sets=512 way_incr=16384
    D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
    Memory: 222848k/262144k available (3360k kernel code, 1045k data, 136k init)
    SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    Hierarchical RCU implementation.
    NR_IRQS:600
    Failed to enable clk CLKA_REF, ignoring
    Failed to enable clk CLKA_PLL0LS, ignoring
    console [ttyAS0] enabled
    sh_tmu: TMU0 used for clock events
    sh_tmu: TMU0 used for periodic clock events
    sh_tmu: TMU1 used as clock source
    Calibrating delay loop... 538.62 BogoMIPS (lpj=1077248)
    Mount-cache hash table entries: 512
    CPU: STx7105
    NET: Registered protocol family 16
    Configuring FLASH for boot-from-SPI
    bio: create slab <bio-0> at 0
    SCSI subsystem initialized
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    DMA: Registering DMA API.
    Switching to clocksource TMU1
    NET: Registered protocol family 2
    IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
    TCP established hash table entries: 8192 (order: 4, 65536 bytes)
    TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
    TCP: Hash tables configured (established 8192 bind 8192)
    TCP reno registered
    NET: Registered protocol family 1
    RPC: Registered udp transport module.
    RPC: Registered tcp transport module.
    RPC: Registered tcp NFSv4.1 backchannel transport module.
    Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    Slow work thread pool: Starting up
    Slow work thread pool: Ready
    NTFS driver 2.1.29 [Flags: R/O].
    JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
    fuse init (API version 7.13)
    JFS: nTxBlock = 1742, nTxLock = 13939
    msgmni has been set to 435
    io scheduler noop registered
    io scheduler anticipatory registered (default)
    lirc_dev: IR Remote Control driver registered, major 61
    lirc-stm: probe found data for platform device lirc-stm
    lirc-stm: STM LIRC plugin using IRQ 125 in IR mode
    lirc_dev: lirc_register_driver: sample_rate: 0
    STMicroelectronics LIRC driver initialized.
    STMicroelectronics ASC driver initialized
    stm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-asc
    stm-asc.1: ttyAS1 at MMIO 0xfd033000 (irq = 120) is a stm-asc
    loop: module loaded
    MiPHY driver style MiPHY3-65 probed successfully
    MiPHY3-65, c1.5 Claimed by sata-stm


  2. #2
    Neuer Benutzer
    Registriert seit
    27.08.2012
    Beiträge
    22
    Thanks
    10
    Thanked 0 Times in 0 Posts
    I think there is a problem in this area ?

    bpa2: partition 'bigphysarea' created at 0x40e95000, size 24000 kB (0x01770000 B)


  3. #3
    VIP
    Registriert seit
    13.05.2012
    Beiträge
    759
    Thanks
    35
    Thanked 345 Times in 243 Posts
    No, your problem is here:
    MiPHY3-65, c1.5 Claimed by sata-stm ==> it hangs while initing the tap inteface

    Decomment in /arch/sh/boards/mach-hdk7105 in setup.c this line : stx7105_configure_sata(0);

    or use the right setup patch for the stm24_211_kernel from tdt git

    Edit:
    Yeah the bigphys seems also wrong, these are the original adresses:

    static struct bpa2_partition_desc bpa2_parts_table[] = {
    {
    .name = "bigphysarea",
    .start = 0x48000000,
    .size = 0x02000000, /* 32 Mb */
    .flags = 0,
    .aka = NULL
    },
    {
    .name = "LMI_IO",
    .start = 0x4A000000,
    .size = 0x06000000, /* 92 Mb */
    .flags = 0,
    .aka = LMI_IO_partalias
    Geändert von DboxOldie (16.11.2012 um 19:54 Uhr)

  4. The Following User Says Thank You to DboxOldie For This Useful Post:



  5. #4
    Neuer Benutzer
    Registriert seit
    27.08.2012
    Beiträge
    22
    Thanks
    10
    Thanked 0 Times in 0 Posts

    Image hangs on booting

    Thanks. Will check that out. It does seem to be picking up the wrong patch so I'll check why that is happening.


Ähnliche Themen

  1. [ufs910] booting...
    Von morly im Forum Beta Enigma2 Bereich für alle SH4 STB
    Antworten: 71
    Letzter Beitrag: 19.03.2013, 23:04
  2. [1008 SE+/hs7810a] Time in deep standby and booting time problems
    Von sulge im Forum Beta Enigma2 Bereich für alle SH4 STB
    Antworten: 2
    Letzter Beitrag: 10.09.2012, 16:55

Berechtigungen

  • Neue Themen erstellen: Ja
  • Themen beantworten: Ja
  • Anhänge hochladen: Ja
  • Beiträge bearbeiten: Ja
  •