Anleitung: UFS 912 flash Image

[ttspieler45]

In den kann ich leider nicht reinschauen. Ich probiere es dann mal mit einem genderchanger. Erst einmal vielen dank für die super Unterstützung, civer. Ich melde mich, wenn ich denn Adapter habe und meine Box dann Auslesen kann. Hoffentlich....
Gruss

[Civer]

genau, ein Bild ist evtl. besser als meine schriftliche Erklärung!

[TheChip]

Da ich selber so einen gekauften Adapter hab, kann ich aus eigener Erfahrung sagen, das es mit einem Genderchanger allein nicht getan ist. Du benötigst zusätzlich ein Nullmodemkabel.

[Civer]

Ja, das ist dann natürlich die Voraussetzung! Mit gc hat man natürlich dann sowieso keine Möglichkeit mehr, den Adapter direkt am PC an den COM-Port zu hängen. Somit ist ein Nullmodemkabel (das Rx/Tx dann dreht) nötig. Habe das dann als "selbstverständlich" angesehen, hasta ber recht. Etwas unglücklich von mir!

[ttspieler45]

Moin alle,

was lange...... ;-) Ich habe nun den Zugriff über Putty auf meine 912. Allerdings kann ich über das Tool von Morly (1.4) die Boottargs nicht auslesen, da das Programm abstürzt, wenn ich die Box an mache. Naja, warum auch einfach, wenn...... Egal. Mit Putty kann ich darauf zugreifen. Was benötigt ihr, um mein "Updated Failed" beim updatescript zu lösen??
VG

[ttspieler45]

So, ich hänge mal das LOG an:
Was sind das für kryptische Zeichen bei "Name = bootfile, Value = ", Sektor defekt?? Ist das der Grund, warum ich das Script nicht ausführen kann?? Wie kann ich die Boottargs nun so wieder verändern, das ich ENIGMA flashen kann??!

VG

Board: STx7111-Mboard (MB618)  [32-bit mode]


U-Boot 1.3.1 (Nov 30 2009 - 11:46:12) - stm23-2008-06-03

DRAM:  256 MB
NOR:    4 MB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Serial 3 Intialized
buad = 19200, p2 val = 1109, t = c9, buadrate = 1
buad = 19200, p2 val = 1109, t = c9, buadrate = 3ee
VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD using PIC
Test Class : GetInstance()
Test Class : GetInstance()
RawBuffer.cpp at RawBuffer ,29
FD = 0
Test Class : GetInstance()
SWRecoveryHandler.cpp at Recover ,56
No Recovery Needed
End of testCpp
Hit any key to stop autoboot:  0

Loading from nand0, offset 0x0
   Image Name:   Linux-2.6.23.17_stm23_0119-MB618
   Created:      2010-12-08   9:02:06 UTC
   Image Type:   SuperH Linux Kernel Image (gzip compressed)
   Data Size:    2101033 Bytes =  2 MB
   Load Address: 80800000
   Entry Point:  80801000
Original bootargs = console=ttyAS0,115200 root=/dev/mtdblock1 bigphysarea=5120
ethaddr = 00:D0:55:0E:11:C4

new Params = console=ttyAS0,115200 root=/dev/mtdblock1 bigphysarea=5120 stmmacet           h=ethaddr:00:D0:55:0E:11:C4

## Booting image at 84000000 ...
   Image Name:   Linux-2.6.23.17_stm23_0119-MB618
   Created:      2010-12-08   9:02:06 UTC
   Image Type:   SuperH Linux Kernel Image (gzip compressed)
   Data Size:    2101033 Bytes =  2 MB
   Load Address: 80800000
   Entry Point:  80801000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ...  START = 556106
 END = 36182
OK

Starting kernel console=ttyAS0,115200 root=/dev/mtdblock1 bigphysarea=5120 stmma           ceth=ethaddr:00:D0:55:0E:11:C4
 - 0x00000000 - 0 ...

Linux version 2.6.23.17_stm23_0119-MB618_7111-STSDK (kdhong@kdhong) (gcc version            4.2.4 (snapshot) (STMicroelectronics/Linux Base 4.2.4-46)) #292 PREEMPT Wed Dec            8 10:02:04 CET 2010
Booting machvec: mb618
Node 0: start_pfn = 0x40000, low = 0x48000
Zone PFN ranges:
  Normal     262144 ->   294912
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:   262144 ->   294912
STMicroelectronics STx7111 Mboard initialisation
STx7111 version 3.x
Built 1 zonelists in Zone order.  Total pages: 32512
Kernel command line: console=ttyAS0,115200 root=/dev/mtdblock1 bigphysarea=5120            stmmaceth=ethaddr:00:D0:55:0E:11:C4

bpa2: partition 'bigphysarea' created at 0x40d08000, size 20480 kB (0x01400000 B           )
Failed mb618 EPLD test (off 04, res 00)
PID hash table entries: 512 (order: 9, 2048 bytes)
Using tmu for system timer
Using 25.000 MHz high precision timer.
Console: colour dummy device 80x25
console [ttyAS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 97024k/131072k available (2889k kernel code, 826k data, 116k init)
PVR=04909200 CVR=60880000 PRR=00009a10
I-cache : n_ways=2 n_sets=512 way_incr=16384
I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Mount-cache hash table entries: 512
CPU: STx7111
NET: Registered protocol family 16
Configuring EMI Bank1 for NAND device
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: SuperH clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/O].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
yaffs Dec  7 2010 23:13:05 Installing.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
STMicroelectronics ASC driver initialized
GPIO 1 0 is occupied by stasc
GPIO 1 1 is occupied by stasc
GPIO 1 4 is occupied by stasc
GPIO 1 5 is occupied by stasc
stasc.0: ttyAS0 at MMIO 0xfd031000 (irq = 122) is a stasc
stasc.1: ttyAS1 at MMIO 0xfd032000 (irq = 121) is a stasc
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
STMMAC driver:
        platform registration... <6>done!
        GMAC - user ID: 0x10, Synopsys ID: 0x33
s_env_mac[0] = 0
s_env_mac[1] = 0
s_env_mac[2] = :
s_env_mac[3] = D
s_env_mac[4] = 0
s_env_mac[5] = :
s_env_mac[6] = 5
s_env_mac[7] = 5
s_env_mac[8] = :
s_env_mac[9] = 0
s_env_mac[10] = E
s_env_mac[11] = :
s_env_mac[12] = 1
s_env_mac[13] = 1
s_env_mac[14] = :
s_env_mac[15] = C
s_env_mac[16] = 4
get ether addr = 0, d0, 55, e, 11, c4
STMMAC MII Bus: probed
STe100p: Registered new driver
STe101p: Registered new driver
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver zd1201
usbcore: registered new interface driver usb8xxx
physmap platform flash device: 00400000 at 00000000
CFI MFR = c2 DEV = 227e
devsize = 400000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Using physmap partition information
Creating 2 MTD partitions on "physmap-flash":
0x00000000-0x00080000 : "Boot firmware :        0xA000.0000-0xA007.FFFF"
0x00080000-0x00400000 : "NOR Root -             0xA008.0000-0xA03F.FFFF"
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bi           t)
Scanning device for bad blocks
Bad eraseblock 378 at 0x02f40000
Bad eraseblock 861 at 0x06ba0000
Bad eraseblock 1009 at 0x07e20000
Creating 4 MTD partitions on "gen_nand.1":
0x00000000-0x00300000 : "NAND KERNEL -0x0000.0000-0x002F.FFFF"
0x00300000-0x02800000 : "NAND ROOT  -   0x0030.0000-0x005F.FFFF"
0x02800000-0x05000000 : "Config Data - YAFFS 0x0160.0000-0x03FF.FFFF"
0x05000000-0x08000000 : "NAND Data Block - writable FS, YAFFS"
st-usb st-usb.0: st-ehci
st-usb st-usb.0: new USB bus registered, assigned bus number 1
st-usb st-usb.0: irq 169, io mem 0xfe1ffe00
st-usb st-usb.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
usb 1-1: new high speed USB device using st-usb and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.4: new high speed USB device using st-usb and address 3
usb 1-1.4: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
STMicroelectronics - Coprocessors st231 Init
st-coprocessor-0: No RAM reserved
st231.0 Coprocessor -------------------------------------------
    not configured!
---------------------------------------------------------------
st-coprocessor-1: No RAM reserved
st231.1 Coprocessor -------------------------------------------
    not configured!
---------------------------------------------------------------
stm_rng hardware driver 1.0 configured
heartbeat: version 0.1.1 loaded
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory:/etc/init.d/rcS running...
Remounting root file system in read-write mode...mount: Can't find / in /etc/fst           ab
: Success
mount: Mounting / on (null) failed: Success
                                                                     [FAILED]
/etc/rcS.d/S200mountfs: /etc/rcS.d/S200mountfs: 91: cannot create /etc/mtab: Rea           d-only file system
mount: Can't find / in /etc/fstab
: Success
mount: Mounting / on (null) failed: Success
Mounting other file systems...yaffs: dev is 32505860 name is "mtdblock4"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.4, "mtdblock4"
yaffs: restored from checkpoint
yaffs_read_super: isCheckpointed 1
yaffs: dev is 32505859 name is "mtdblock3"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.3, "mtdblock3"
yaffs: restored from checkpoint
yaffs_read_super: isCheckpointed 1
yaffs: dev is 32505861 name is "mtdblock5"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.5, "mtdblock5"
yaffs: restored from checkpoint
yaffs_read_super: isCheckpointed 1
                                                                     [  OK  ]
Bringing up the loopback interface...                                [  OK  ]
Setting up hostname...(none)
                                                                     [  OK  ]
Setup Ethernet HW Address... : skipped
Setup Ramfs... : skipped
Invoking Telnet Server...
telnetd: '/bin/login' unavailable.
Telnet Server Started...
mount: Mounting /proc on /proc failed: Device or resource busy


BusyBox v1.1.0 (2006.03.02-09:48+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

Boot Normal Mode
config/start.sh does not exist.... running /app/start.sh
MODULE_INSTALL_DIR = /app/modules/
stos_core: module license 'ST Microelectronics' taints kernel.
Load module stos_core [?]               by insmod (pid 435)
Load module stsys_ioctl [252]           by insmod (pid 437)
Can not open config file
mode=0
kmsg=0
serverip=
port=0
outpath=
/dev/lxload
mknod -m 0660 /dev/lxload c 251 0
[LOG]: CRC = c80c6843 c80c6843 -> Load in (/EnvList.cpp 135)
[LOG]: No more Environment... -> Load in (/EnvItem.cpp 89)
[LOG]: Name = baudrate, Value = 115200 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = ethaddr, Value = 00:D0:55:0E:11:C4
 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = jPER, Value = 0 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = jSCR, Value = if test ${jON} = 1;then nand read 83FFFC00 400000 40           0;autoscr 83FFFC00; fi -> Print in (/EnvItem.cpp 121)
[LOG]: Name = jDEV, Value = sda1 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = bootfile, Value = ▒
                                 ▒▒▒▒▒▒
                                       ▒Cs#▒
                                            ▒s#▒
                                                ▒t#▒
                                                    ▒ct#▒
                                                         ▒▒t#▒
                                                              ▒#u#▒
                                                                   ▒u#▒
                                                                       ▒▒u#▒
                                                                            ▒Cv#           ▒
 ▒v#▒
     ▒w#▒
         ▒cw#▒
              ▒▒w# -> Print in (/EnvItem.cpp 121)
[LOG]: Name = gatewayip, Value = 192.168.0.1 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = jON, Value = 0 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = stdin, Value = serial -> Print in (/EnvItem.cpp 121)
[LOG]: Name = stdout, Value = serial -> Print in (/EnvItem.cpp 121)
[LOG]: Name = stderr, Value = serial -> Print in (/EnvItem.cpp 121)
[LOG]: Name = bootargs, Value = console=ttyAS0,115200 root=/dev/mtdblock1 bigphy           sarea=5120 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = bootdelay, Value = 0 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = ipaddr, Value = 192.168.101.201 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = serverip, Value = 192.168.101.202 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = autoload, Value = n -> Print in (/EnvItem.cpp 121)
[LOG]: Name = netmask, Value = 255.255.252.0 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = board, Value = mb618 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = unprot, Value = protect off $monitor_sec -> Print in (/EnvItem.cpp            121)
[LOG]: Name = filesize, Value = 1E17A00 -> Print in (/EnvItem.cpp 121)
[LOG]: Name = ncmd, Value = nboot 84000000 0 0;bootm 84000000 -> Print in (/EnvI           tem.cpp 121)
[LOG]: Name = nargs, Value = $bootargs factorytest=1 -> Print in (/EnvItem.cpp 1           21)
[LOG]: Name = nncmd, Value = $ncmd -> Print in (/EnvItem.cpp 121)
[LOG]: Name = nnargs, Value = bootargs $nargs -> Print in (/EnvItem.cpp 121)
[LOG]: Name = bootcmd, Value = nboot 84000000 0 0;bootm 84000000 -> Print in (/E           nvItem.cpp 121)
[LOG]: Name = boot_version, Value = 105 -> Print in (/EnvItem.cpp 121)
[LOG]: [THREAD STARTING] Start PID = 452, NAME = Micom WriteThread -> ThreadMain           Handler in (/Thread.cpp 286)
[LOG]: Thread Name LXLOAD(video1)       : LX loaded => Base=0x40000000 - Last=0x           40153298 - Size=1389208
Micom WriteThread State 0-->1 -> SetStatus in (/Thread.cpp 209)
[LOG]: [THREAD STARTING] Start PID = 453, NAME = Micom ReadThread -> ThreadMainH           andler in (/Thread.cpp 286)
[LOG]: Thread Name Micom ReadThread State 0-->1 -> SetStatus in (/Thread.cpp 209           )
[LOG]: Waiting For Micom Write.. 10 -> Write in (/MicomDevice.cpp 341)
[LOG]: Waiting For Micom Write.. 20 -> Write in (/MicomDevice.cpp 341)
[LOG]:  -> ReadThread in (/MicomDevice.cpp 1894)
[LOG]:  -> ReadThread in (/MicomDevice.cpp 1900)
read_len = 8 //85 1 5 ff ff ff 88 d [LOG]: Micom Version 1 5 -> SetModel in (/Mi           comDevice.cpp 1983)
read_len = 8 //b9 dc d8 8 24 1b b4 d
[LOG]: day = 1 Sun Sep  1 08:36:27 2013
 -> GetTime in (/MicomDevice.cpp 2473)
[LOG]: MJD = 56536 epoch = 1378024587/1378024587, time = Sun Sep  1 08:36:27 201           3
/Sun Sep  1 08:36:27 2013
, 08:36:27 -> GetTime in (/MicomDevice.cpp 2476)
[LOG]: Boot Type = 0 -> StandbyMgr in (/StandbyMgr.cpp 319)
[LOG]: 77 c2 ff -> ReadThread in (/MicomDevice.cpp 1917)
[LOG]: Wake up mode = c2, deepStandbyValue = 1 -> StandbyMgr in (/StandbyMgr.cpp            326)
[LOG]: Setting Wakeup = 1 -> StandbyMgr in (/StandbyMgr.cpp 348)
[LOG]: StartByte = 4, PageSize = 16, ByteCount = 1 -> SetValueImpl in (/EEPromSl           ot.cpp 283)
1 0 ff ff ff ff ff ff ff ff ff ff 0 0 0 0
[LOG]: LAUNCH APP!! -> LaunchApp in (/StandbyMgr.cpp 966)
[LOG]: StartByte = 0, PageSize = 16, ByteCount = 1 -> SetValueImpl in (/EEPromSl           ot.cpp 283)
1 1 0 0 1 0 ff ff ff ff ff ff ff ff ff ff
[LOG]:  -> SetLEDOnOff in (/MicomDevice.cpp 2095)
[LOG]:  -> SetLEDOnOff in (/MicomDevice.cpp 2098)
[LOG]:  -> SetLEDOnOff in (/MicomDevice.cpp 2101)
/dev/lxload
mknod -m 0660 /dev/lxload c 251 0
[LOG]: Invoke /config/startapp.sh nodebug : PID Parent= 439, Child = 466 -> Exec           Wait in (/ExecShell.cpp 168)
[LOG]: Child PID... -> ExecWait in (/ExecShell.cpp 163)
loading audio binary file
start nodebug
LXLOAD(audio1)  : LX loaded => Base=0x40400000 - Last=0x404e8300 - Size=951040
Load module stpower_core [252] by insmod (pid 496)
Load module stuart_core [251]           by insmod (pid 496)
Load module stevt_core [?]              by insmod (pid 496)
Load module stcommon_core [?]           by insmod (pid 496)
Load module stclkrv_core [?]            by insmod (pid 496)
Load module stfdma_core [250]           by insmod (pid 496)
Load module stmerge_core [?]            by insmod (pid 496)
Load module stavmem_core [?]            by insmod (pid 496)
Load module stbuffer_core [?]           by insmod (pid 496)
Load module stinject_core [?]           by insmod (pid 496)
Load module sti2c_core [?]              by insmod (pid 496)
Load module stpio_core [?]              by insmod (pid 496)
Load module stpwm_core [?]              by insmod (pid 496)
Load module stdenc_core [?]             by insmod (pid 496)
Load module stlayer_core [?]            by insmod (pid 496)
Load module stvout_core [?]             by insmod (pid 496)
Load module stvtg_core [?]              by insmod (pid 496)
Load module stvid_core [?]              by insmod (pid 496)
Load module stos_core [?]               by insmod (pid 496)
Load module stvmix_core [?]             by insmod (pid 496)
Load module stgxobj_core [?]            by insmod (pid 496)
Load module staudlx_core [249]          by insmod (pid 496)
Load module stttx_core [?]              by insmod (pid 496)
Load module stvbi_core [?]              by insmod (pid 496)
Load module stblit_core [?]             by insmod (pid 496)
Load module stsmart_core [248]          by insmod (pid 496)
Load module sthdmi_core [?]             by insmod (pid 496)
Load module stkeyscn_core [?]           by insmod (pid 496)
Load module stpti4_core [?]             by insmod (pid 496)
Load module stfrontend_core [247]       by insmod (pid 496)
Load module stpower_ioctl [246] by insmod (pid 496)
Load module stuart_ioctl [245]          by insmod (pid 496)
Load module stevt_ioctl [244]           by insmod (pid 496)
Load module stcommon_ioctl [243]        by insmod (pid 496)
Load module stclkrv_ioctl [242]         by insmod (pid 496)
Load module stfdma_ioctl [241]          by insmod (pid 496)
Load module stmerge_ioctl [240]         by insmod (pid 496)
Load module stavmem_ioctl [239]         by insmod (pid 496)
Load module stbuffer_ioctl [238]        by insmod (pid 496)
Load module stinject_ioctl [237]        by insmod (pid 496)
Load module sti2c_ioctl [236]           by insmod (pid 496)
Load module stspi_ioctl [235]           by insmod (pid 496)
Load module stpio_ioctl [234]           by insmod (pid 496)
Load module stpwm_ioctl [233]           by insmod (pid 496)
Load module stdenc_ioctl [232]          by insmod (pid 496)
Load module stlayer_ioctl [230]         by insmod (pid 496)
Load module stvout_ioctl [229]          by insmod (pid 496)
Load module stvtg_ioctl [228]           by insmod (pid 496)
Load module stvid_ioctl [227]           by insmod (pid 496)
Load module stvmix_ioctl [226]          by insmod (pid 496)
Load module stgxobj_ioctl [225]         by insmod (pid 496)
Load module stttx_ioctl [223]           by insmod (pid 496)
Load module stvbi_ioctl [222]           by insmod (pid 496)
Load module stblit_ioctl [221]          by insmod (pid 496)
Load module stsmart_ioctl [220]         by insmod (pid 496)
Load module sthdmi_ioctl [219]          by insmod (pid 496)
Load module stsys_ioctl [218]           by insmod (pid 496)
Load module stkeyscn_ioctl [217]        by insmod (pid 496)
Load module stpti4_ioctl [216]          by insmod (pid 496)
Load module stfrontend_ioctl [215]      by insmod (pid 496)
Module stapler_core (rev: STAPLER-REL_1.3.1) loaded by insmod (pid 500)
Load module sttkdma_core by insmod (pid 502)
Load module sttkdma_ioctl [214] by insmod (pid 504)
Load module stdrmcrypto_core (revision: STDRMCRYPTO-REL_1.4.2) by insmod (pid 50           6)
STTKDMA revision: STTKDMA-REL_3.3.1 NOT_BOOTED-st40r2-4.4.0-linux-4-m1 customer            mode is: -1
Load module stdrmcrypto_ioctl by insmod (pid 508)
mgfb Allocation Size = 1000000
mem_start = 8a000000 48000000 1000000
stgfb_core_set_layers:  Store fb memory start + length
stgfb_core_set_layers: mgfb_fb_info[count].par.mem_start 48000000
 mgfb_fb_info[count].par.mem_len 01000000
 mgfb_fb_info[count].par.virtual_mem_start 8a000000
 on device 0
stgfb_core_set_layers:  mode = 0
stgfb_core_set_layers:  format = 0x0
[MGFB_setFB] Framebuffer registered!!!
GPIO 4 6 is occupied by PWM
stgfb_core_set_par: Old Params-----:1280x720
 bits per pixel=32
 Margin left=220 right=110
----
stgfb_core_set_par: New params----:
 1280x720
 virtual=1280x720 bits per pixel=32
 Margin left=220 right=110
 bits per pixel=32 R(16,8) G(8,8) B(8,0) A(24,8)
------
>>> stgfb_decode_var
bpp inside decoding stage 32
v->transp.offset  24
v->red.offset     16
v->red.length     8
v->green.offset   8
v->green.length   8
v->blue.length    8
v->blue.offset    0
v->transp.length  8
Decode_var: videomode set to 0
<<< stgfb_decode_var
Bitmap format moving to 0
[mgfb_core_set_par] disp_viewport_set_params() success
[mgfb_core_set_par] stgfb_fb_info[device_num].par.mem_start 48000000
 stgfb_fb_info[device_num].par.mem_len 01000000
 stgfb_fb_info[device_num].par.virtual_mem_start 8a000000
 on device 0
Change : Format=0, YRes=1280, XRes=720, XVRes=1280, YVRes=720/5120,
[mgfb_core_set_par] Mem start 48000000 length 01000000
[mgfb_core_set_par] stgfb_fb_info[device_num].info.var.xres = 1280
[mgfb_core_set_par] stgfb_fb_info[device_num].info.var.yres = 720
save exit: isCheckpointed 1
save exit: isCheckpointed 1
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
stmmac_timer: TMU2 Timer ON (freq 512Hz)
PHY: 0:03 - Link is Up - 100/Full

[morly]

Allerdings kann ich über das Tool von Morly (1.4) die Boottargs nicht auslesen, da das Programm abstürzt, wenn ich die Box an mache. VG

Interessiert mich natürlich... kannst das Tool via Konsole starten und mir die Ausgabe posten?
Haste mal versucht das Tool als Admin auszuführen?
Lg

- - - Aktualisiert - - -

Was sind das für kryptische Zeichen bei "Name = bootfile, Value = ", Sektor defekt??

OK - das wird der Grund sein...
Aber du kannst die Bootargs händisch verändern, der Befehl geht so:

setenv Value xyz

(wobei Value der jeweilige Eintrag ist und xyz der neue Wert)
Wenn alle gesetzt musst noch ein:

saveenv

machen, dann sind sie auch gespeichert

Lass dir mal von wem die richtigen Bootargs posten - dann kannst du sehen was nicht passt

[ttspieler45]

Interessiert mich natürlich... kannst das Tool via Konsole starten und mir die Ausgabe posten?
Haste mal versucht das Tool als Admin auszuführen?
Lg

- - - Aktualisiert - - -


OK - das wird der Grund sein...
Aber du kannst die Bootargs händisch verändern, der Befehl geht so:

setenv Value xyz

(wobei Value der jeweilige Eintrag ist und xyz der neue Wert)
Wenn alle gesetzt musst noch ein:

saveenv

machen, dann sind sie auch gespeichert

Lass dir mal von wem die richtigen Bootargs posten - dann kannst du sehen was nicht passt

Ich führe das Tool immer als admin aus. Was meinst du damit das Tool über Konsole zu starten?
Edit: Erst nachdenken, dann posten ;-) Du meinst bestimmt über die Eingabeaufforderung. Aber wie bringe ich das Proggie dazu, zu loggen?

Und an wen muss ich mich wenden für die korrekten Bootargs??

Vielen Dank.
VG

[morly]

Ja genau das meinte ich - aber sorry, bist ja unter Windows, da gibts keine Ausgaben!
Aber egal - ich glaub es liegt an den verworrenen Einträgen...
Zu den Bootargs, dachte es liest schon wer mit, aber egal, am einfachsten nen Thread aufmachen und darum bitten (musst aber anmerken welche OHNE DuckBA)

[Lambda2013]

Hallo zusammen!
Ich versuche jetzt schon eine kleine Ewigkeit, ein Image auf meinem 912er zu installieren. Vollkommen Erfolglos....
Egal was ich mache, es steht immer "No Update File" im Display. Egal ob ich jetzt diese "Updatescript"-Datei oder ein Image auf einen Stick kopiere.
Habe schon ein paar Sticks ausprobiert... Kein Erfolg...
Habt ihr vielleicht für einen laien noch irgendwelche Ideen?????