+ Antworten
Seite 1 von 3 123 LetzteLetzte
Ergebnis 1 bis 10 von 24
  1. #1
    Erfahrener Benutzer
    Registriert seit
    10.11.2012
    Beiträge
    140
    Thanks
    69
    Thanked 10 Times in 9 Posts

    STB7100 bord de référence cpu family: sh4

    hello I have a receiver family sh4 I would like to put in enigma2 if possible I said there is no rs232 here is a log thank you to the expert .
    Angehängte Dateien Angehängte Dateien


  2. #2
    Erfahrener Benutzer
    Registriert seit
    10.11.2012
    Beiträge
    140
    Thanks
    69
    Thanked 10 Times in 9 Posts
    hello all person help me .


  3. #3
    Erfahrener Benutzer
    Registriert seit
    15.12.2012
    Beiträge
    183
    Thanks
    176
    Thanked 80 Times in 56 Posts
    You have to see about your mother-board and locate the connector or the pitches prepared to leave the UARTx used to debug service!

    For example, Fulan STi7111 series has four UART ... but as seen in the circuit diagram, only two are used for the debug service purpose (UART2 & UART3).

    Others (UART0 and UART1) are configurated for used how general PIO (IN/OUT) access to other devices inside!

    So every mother-board revision with its STicore chipset may be different from the other !

    Ciao ... arci

  4. The Following 2 Users Say Thank You to arci For This Useful Post:



  5. #4
    Erfahrener Benutzer
    Registriert seit
    10.11.2012
    Beiträge
    140
    Thanks
    69
    Thanked 10 Times in 9 Posts
    hello thank you for reponse UART0 but I do not know where it is.


  6. #5
    Erfahrener Benutzer
    Registriert seit
    15.12.2012
    Beiträge
    183
    Thanks
    176
    Thanked 80 Times in 56 Posts
    The easiest thing is to open the receiver and take several photos of the mother-board.

    You'll see that someone can help you !

    rgs ... arci


  7. #6
    Erfahrener Benutzer
    Registriert seit
    10.11.2012
    Beiträge
    140
    Thanks
    69
    Thanked 10 Times in 9 Posts
    ok thank you tonight I am the office.


  8. #7
    Erfahrener Benutzer
    Registriert seit
    15.12.2012
    Beiträge
    183
    Thanks
    176
    Thanked 80 Times in 56 Posts
    If you have not yet found!!

    With google you can find the SDK document ...

    ... This will be very useful!

    Needless to say that these are confidential documents!

    rgs ... arci
    Geändert von arci (28.03.2013 um 16:26 Uhr)


  9. #8
    Erfahrener Benutzer
    Registriert seit
    10.11.2012
    Beiträge
    140
    Thanks
    69
    Thanked 10 Times in 9 Posts
    ok thank you for your help


  10. #9
    Erfahrener Benutzer
    Registriert seit
    10.11.2012
    Beiträge
    140
    Thanks
    69
    Thanked 10 Times in 9 Posts
    @link_RS232.pdf
    hello arci


  11. #10
    Erfahrener Benutzer
    Registriert seit
    15.12.2012
    Beiträge
    183
    Thanks
    176
    Thanked 80 Times in 56 Posts
    Zitat Zitat von samkooke Beitrag anzeigen
    @link_RS232.pdf
    hello arci
    Hi

    I see a module transceiver MAX232 (convert interface for RS232 to TTL UART signal) ... Is it of your receiver ?

    If yes !?!

    On the connector (CON 3 PS103) there are the TX/RX signal converted to RS232 EIA (PC- standard) ...

    [CON 3] You can take RXD (IN pin 1) - TXD (OUT pin 2) - GND (pin 3) for connected to RS232 DIP9 (serial comunication port) of your PC ...

    For right connection on PC RS232 DIP 9 Female ... refer to standard pinout (RX/TX) !

    P.S. On attached image ... there is the pinout of the MAX232 IC!

    Klicken Sie auf die Grafik für eine größere Ansicht 

Name:	Max232A.gif 
Hits:	63 
Größe:	20,7 KB 
ID:	3671

    rgs ... arci


Berechtigungen

  • Neue Themen erstellen: Ja
  • Themen beantworten: Ja
  • Anhänge hochladen: Ja
  • Beiträge bearbeiten: Ja
  •