Hallo zusammen,
hatte schon in der Anleitung von der UFS 922 dieses Problem geschildert, jetzt mach Ich es noch etwas ausführlicher :-)
Ich hab meine Kathi komplett platt gemacht (Firmware komplett neu geflasht auf 2.10 und die Festplatte in den Rohzustand versetzt) dann Barry Allen 1.61 über MPI installiert und die neuste HDMU Firmware geflasht. Soweit so gut Barry Allen funktoniert, Orginal Firmware geht, HDMU geht nicht :-(
Ich habe den Bootvorgang über die Serielle Schnittstelle ausgelesen, werd da aber nicht wirklich schlau draus.
Kann mir evtl. jemand helfen ???
Code:
Board: STb7100-Mboard (MB411)  [29-bit mode]


U-Boot 1.3.1 (Oct 21 2009 - 15:59:46) - stm23-2008-06-03

DRAM:  64 MB
NOR:   16 MB
In:    serial
Out:   serial
Err:   serial
Serial 3 Intialized
VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD using PIC
Test Class : GetInstance()
Test Class : GetInstance()
RawBuffer.cpp at RawBuffer ,29
FD = 0
SWRecoveryHandler.cpp at Recover ,46
No Recovery Needed
End of testCpp
Hit any key to stop autoboot:  0
Original bootargs = console=ttyAS0,115200 root=/dev/mtdblock3 mem=83m bigphysare                             a=5632 coprocessor_mem=3m@0x04000000,3m@0x04300000 loglevel=1
ethaddr = 00:D0:55:04:A2:AD

new Params = console=ttyAS0,115200 root=/dev/mtdblock3 mem=83m bigphysarea=5632                              coprocessor_mem=3m@0x04000000,3m@0x04300000 loglevel=1 stmmaceth=ethaddr:00:D0:5                             5:04:A2:AD

## Booting image at 80040000 ...
   Image Name:   Linux-2.6.23.17-MB411_7109-STSDK
   Created:      2009-12-08  23:40:22 UTC
   Image Type:   SuperH Linux Kernel Image (gzip compressed)
   Data Size:    1820882 Bytes =  1.7 MB
   Load Address: 84601000
   Entry Point:  84602000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel console=ttyAS0,115200 root=/dev/mtdblock3 mem=83m bigphysarea=56                             32 coprocessor_mem=3m@0x04000000,3m@0x04300000 loglevel=1 stmmaceth=ethaddr:00:D                             0:55:04:A2:AD
 - 0x00000000 - 0 ...

/etc/init.d/rcS running...
Remounting root file system in read-write mode...mount: Can't find / in /etc/fst                             ab
: Success
mount: Mounting / on (null) failed: Success
                                                                     [FAILED]
/etc/rcS.d/S200mountfs: /etc/rcS.d/S200mountfs: 91: cannot create /etc/mtab: Rea                             d-only file system
mount: Can't find / in /etc/fstab
: Success
mount: Mounting / on (null) failed: Success
Mounting other file systems...                                       [  OK  ]
Bringing up the loopback interface...                                [  OK  ]
Setting up hostname...(none)
                                                                     [  OK  ]
Setup Ethernet HW Address... : skipped
Setup Ramfs... : skipped
Invoking Telnet Server...
telnetd: '/bin/login' unavailable.
Telnet Server Started...


BusyBox v1.1.0 (2006.03.02-09:48+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/config/start.sh exists .... running /config/start.sh
start Barry Allen
ln: /var/ba/ba: File exists
OK - booting 1 HDMU
-------------------------------
rm: cannot remove `/var/standby.log': No such file or directory
rm: cannot remove `/var/ba': No such file or directory
calculated crc = 0x852c3fd7 ->read crc = 0x852c3fd7
calculated crc = 0x852c3fd7 ->read crc = 0x852c3fd7
Resô

Board: STb7100-Mboard (MB411)  [29-bit mode]


U-Boot 1.3.1 (Oct 21 2009 - 15:59:46) - stm23-2008-06-03

DRAM:  64 MB
NOR:   16 MB
In:    serial
Out:   serial
Err:   serial
Serial 3 Intialized
VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD using PIC
Test Class : GetInstance()
Test Class : GetInstance()
RawBuffer.cpp at RawBuffer ,29
FD = 0
SWRecoveryHandler.cpp at Recover ,46
No Recovery Needed
End of testCpp
Hit any key to stop autoboot:  0
Saving Environment to EEPROM...

Reset IDE: Bus 0: OK
  Device 0: Model: WDC WD2500AVVS-73L2B0  Firm: 01.03A01 Ser#: W -DCWVA21567989
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)

404 bytes read
## Executing script at a4900000
BarryAllen 0.8 bootargs

Reset IDE: Bus 0: OK
  Device 0: Model: WDC WD2500AVVS-73L2B0  Firm: 01.03A01 Ser#: W -DCWVA21567989
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)

1672383 bytes read
Original bootargs = console=ttyAS0,115200 root=/dev/sda5 rw ip=192.168.178.11:19                             2.168.178.1:192.168.178.1:255.255.255.0:kathrein:eth0:off mem=128m init=/bin/dev                             init coprocessor_mem=4m@0x10000000,4m@0x10400000
ethaddr = 00:D0:55:04:A2:AD

new Params = console=ttyAS0,115200 root=/dev/sda5 rw ip=192.168.178.11:192.168.1                             78.1:192.168.178.1:255.255.255.0:kathrein:eth0:off mem=128m init=/bin/devinit co                             processor_mem=4m@0x10000000,4m@0x10400000 stmmaceth=ethaddr:00:D0:55:04:A2:AD

## Error: environment overflow, "bootargs" deleted
## Booting image at a5000000 ...
   Image Name:   Linux-2.6.32.46_stm24_0209
   Created:      2013-07-01  11:10:19 UTC
   Image Type:   SuperH Linux Kernel Image (gzip compressed)
   Data Size:    1672319 Bytes =  1.6 MB
   Load Address: 84001000
   Entry Point:  84002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel @à@@@ðË@ - 0x00000000 - 0 ...
Danke schon mal im Vorraus

Lg
Ralf