good evening what demo do you have?
good evening ;
it's an hs7819 reseller ID 27 xx 20 A0
forever clone to xeobox 7200 id 271520A0 xeobox 270920A0.
Doing some research in stlinux site, I found this
Since the U_Boot variable "load_addr=0x80000000" , can I use these two commands as prescribed after the mtd0 file being loaded on RAM.For NAND Flash
In the case of NAND flash, the flash should be explicitly erased, prior to writing to it.
In the case of NAND, then most access operations need to be multiples of certain page/block sizes. For simplicity, the following code assumes that u-boot.bin fits in 256 KiB (0x40000). However, you may use smallest figures that are appropriately aligned.
Code:MB680> nfs $load_addr /export/u-boot.bin MB680> nand erase 0 40000 MB680> nand write $load_addr 0 40000
I'm trying doing my best , but still need help .
Regards
Geändert von kader_73 (22.04.2014 um 14:49 Uhr) Grund: spelling
hello again ;
still with my f*** machine, i tried to boot from usb as said in the help using usbboot command , mtd0 in root fat32
Code:7119 > usbboot 0x80000000 0:1 Loading from USB device 0, partition 1: Name: usbda1 Type: U-Boot ** Bad Magic Number ** 7119 >
Geändert von kader_73 (23.04.2014 um 16:33 Uhr)
please try and post output
Code:set bootcmd "nand read.jffs2 0x80000000 0x00500000 0x00300000; bootm 0x80000000" boot
hi harry,
was vermutest du am offset 0x500000? soll da in dem flashlayout der ursprünglichen firmware nen kernel liegen? obwohl ich die kiste nicht kenne wäre das sehr ungewöhnlich
@solala: The memory layout of the Fortis HS7119 using Fortis stock firmware is this:With loader 7.XX Fortis is back to flashing partitions at fixed addresses, IRD partition types 7, 8 and probably 9 are no longer flashable with a .IRD file.Code:Fortis HS7119 L7.07 memory map ------------------------------ By memory address: Start End Size Type Purpose MTD IRD fixed DecSt DecSz 0x000000000 - 0x0003FFFFF 0x000400000 Flash, bootloader 0 0 Y 0 MB 4 MB 0x000400000 - 0x0004FFFFF 0x000100000 Flash, configuration 5 2,3,4,5? Y 4 MB 1 MB 0x000500000 - 0x0007FFFFF 0x000300000 Flash, kernel 1 6 Y 5 MB 3 MB 0x000800000 - 0x0067FFFFF 0x006000000 Flash, application 2 1 Y 8 MB 96 MB 0x006800000 - 0x00FFFFFFF 0x009000000 Flash, user? 6 9? Y 104 MB 144 MB 0x00F800000 - 0x00FFFFFFF 0x000800000 Flash, ? 8 - Y 248 MB 8 MB 0x800000000 - 0x8FFFFFFFF 0x100000000 RAM
Regards,
Audioniek.
Geändert von Audioniek (24.04.2014 um 21:34 Uhr)
Receivers: Rebox: RE-4000, 8000, 9000, 2200, 2210, 2220, 4200, 4210, 4220, 8220, 8500, SAB Unix Triple, Golden Media Spark TripleX, Amiko Alien 2+, Sogno Spark Revolution, Kathrein UFS910(1 & 14W)/912/913/922(CX24116 & AVL2108 tuners), Vizyon revolution 820HD PVR, AB IPBox 91HD/9000HD/9000HD rev.2, Xsarius Alpha HD10, nBox BKSA/BSLA/BXZB/BZZB, Vitamin HD 5000
Sats: Astra 1, 2 & 3, Hotbird
Main activity: building my own E2 images for Fortis receivers