fehler beim bauen mit Audioniek git

[Audioniek]

First error: in the kernel .config, the module for wireless is not selected. This is logical, because with wireless drivers any image will be too big to fit flash (it is only 16 Mbyte, the kernel is usually around two, so there only 14 Mbyte left for the rootfs, which is not much and even most Neutrino variants are bigger that that. You have to be aware that you are building for a very old receiver with very little flash memory.

Second error: the rootfs is just 12 kbyte too large. Remove kernel modules you do not need, like the USB serial drivers. As the resulting free space is not large, it is very likely that the image will run slow or not at all.

Third error: the amount of free space on an USB stick and the building of the devs in the flash routines have nothing to do with each other.

Misunderstanding: you do not build for USB. You build an image for a certain receiver. After that has been done, you use the flash environment to convert the image built to the file(s) you need to run it on a box, which can sometimes be in flash memory only, sometimes on a USB stick, or both, depending on the capabilities on the receiver involved and the image built.

My git is fork of the Duckbox Developers git maintained by max. With respect to the UFS910, both gits are effectively the same, as I do not develop for Kathrein receivers. The main difference is the flash environment, which was are rewitten by me.

Last remark: it is still unclear to me what you are trying to achieve. On a UFS910 your options are probably limited to running either E2 or Neutrino off a USB stick.

Regards,

Audioniek.

[turulbird]

it is still unclear to me what you are trying to achieve

The UFS 910 image build exercise just because there are three pieces of UFS 910, the newer image is on them.

The main objective UFS 913 XBMC image build albis 8000 patch.

The XBMC not be possible to transfer the git from?:

git clone https://gitlab.com/FFTEAM/martiis-tdt.git

It does not matter if older...

May be updated?

[thomas]

this is not for UFS910

martii neutrino > spark 7111/7162

[turulbird]

this is not for UFS910

martii neutrino > spark 7111/7162

turulbird@b:~/martiis-tdt/tdt/cvs/cdk$ ./make.sh

  _______                     _____              _     _         _
 |__   __|                   |  __ \            | |   | |       | |
    | | ___  __ _ _ __ ___   | |  | |_   _  ____| | __| |_  __ _| | ___ ___
    | |/ _ \/ _` | '_ ` _ \  | |  | | | | |/  __| |/ /| __|/ _` | |/ _ | __|
    | |  __/ (_| | | | | | | | |__| | |_| |  (__|   < | |_| (_| | |  __|__ \
    |_|\___|\__,_|_| |_| |_| |_____/ \__,_|\____|_|\_\ \__|\__,_|_|\___|___/


Targets:
 1) Kathrein UFS-910
 3) Kathrein UFS-912
 4) Kathrein UFS-922
 5) Topfield 7700 HDPVR
 6) Fortis based (HDBOX)
 7) SpiderBox HL-101
 8) Edision Argus vip
 9) Cuberevo (IPBOX 9000)
10) Cuberevo mini (IPBOX 900)
11) Cuberevo mini2 (IPBOX 910)
12) Cuberevo 250 (IPBOX 91)
13) Cuberevo 9500HD (7000HD)
14) Cuberevo 2000HD
15) Cuberevo mini_fta (200HD)
16) Homecast 5101
17) Octagon 1008
18) SPARK
19) Atevio7500
20) SPARK7162
21) IPBOX9900
22) IPBOX99
23) IPBOX55
24) Fortis HS7810A
25) B4Team ADB 5800S
26) Fortis HS7110
27) WHITEBOX
28) Kathrein UFS-913
Select target (1-28)?

The number one?