fehler beim bauen mit Audioniek git

[ghani]

bei release wird kein audio.elf im /boot erzeugt beim cuberevo mini

[Audioniek]

Will be fixed this evening.

Regards,

Audioniek.

[turulbird]

Rebuild now UFS910, but only:

Welcome! ... Loading enigma1 ..... in the vfd-display.



maxiU-Boot 1.3.1 (May 19 2010 - 23:05:16) - by SoLaLa
Uncompressing Kernel Image ... OK
Starting kernel console=ttyAS0,115200 root=/dev/sda4 rw ip=192.168.002.002:192.168.002.001:192.168.002.001 :255.255.255.0:kathrein:eth0ff mem=64m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr: init=/bin/devinit - 0x00000000 - 0 ...

[Audioniek]

Congratulations.

Regards,

Audioniek.

[ghani]

es kommt jetzt ein fehler, und es erzeugt immer noch kein audio.elf

----- edit -----

damit das geht muss audio7109.elf so umbenannt werden audio_7109.elf im enigma2-release

[turulbird]

Thanks for all help, but UFS910 do not go further ... just only loading....

Why enigma 1 writes on vfd? Build image not enigma 2?

...........................................

UFS 913 error repaired?:
frontcontroller/micom/micom.ko and frontends/multituner/*.ko error no files or directory

Kathrein_UFS913_enigma2_flash_full.data file how to install or convert;
I uImage and rootfs.img should?

Rename *.data to rootfs.img, flashing, but error:

Loading from nand0, offset 0x0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
** Unknown image type
Wrong Image Format for bootm command
ERROR: can't get kernel image!
STB8000>

[Audioniek]

Why enigma 1 writes on vfd? Build image not enigma 2?

This is probably a text from the loader, not from the image. It may be possible to change that in the bootargs.
For the rest, follow the instructions given in the forum.

UFS 913 error repaired?:
frontcontroller/micom/micom.ko and frontends/multituner/*.ko error no files or directory

I cannot reproduce this error, When I build with UFS913, a micom.ko and the frontend .ko's are created and copied to the right location.

Kathrein_UFS913_enigma2_flash_full.data file how to install or convert;
I uImage and rootfs.img should?

Rename *.data to rootfs.img, flashing, but error:

The file Kathrein_UFS913_enigma2_flash_full.data is supposed to be a flash file that can be flashed directly into a UFS913. The procedure is, as I believe: press REC on the remote control during 10 seconds while the box is powering up (also see the forum on how to flash a UFS913).
I you want a rootfs, it is X/flash/tmp/ROOT, the uImage is in X/flash/tmp/KERNEL (after flash.sh has completed) . Be aware that the .elf files are in X/flash/tmp/FW and may need to be copied back to X/flash/tmp/ROOT/boot to get the full rootfs back (the UFS913 has the .elf files in a separate mtd-block).

Please remember I do not own any Kathrein boxes, and have no experience with them.

Regards,

Audioniek.

[turulbird]

I tried to change bootargs and reflash maxi u-boot, but failed so far.


It is not UFS 913; albis8000, modified u-boot, usb flash working, but only uImage and rootfs.img work.


I Try .....


How to pack all files in the /ROOT directory => rootfs.img?

Not find nothing in net, only this:


http://linuxsat-support.com/showthre...ffs2-img-files

.................................................. ...........................

Where would you like your Neutrino image to run?
1) on a USB stick
2) in the receivers flash memory (*)
Select target (1-2)? 1
[3;J

+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+
+ Summary
+ =======
+
+ Receiver : ufs910
+ Linux version : linux-sh4-2.6.32-61
+ Kernel patch level : P0217
+ Image : Neutrino
+ Will run in/on : USB
+
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

-- Prepare root -------------------------------------------------------

Prepare Neutrino root for ufs910.

Root preparation completed.

-- ERROR! -------------------------------------------------------------

!!! ERROR: DEVS ARE MISSING !!!
APPARENTLY MAKEDEV IN prepare_root.sh FAILED.

Exiting...
-----------------------------------------------------------------------

[turulbird]

Output file(s) created in /home/b/Audioniek/StartHere-master/flash/out: 29M
-rw-r--r-- 1 16M máj 19 16:27 miniFLASH.img
-rw-r--r-- 1 33 máj 19 16:27 miniFLASH.img.md5
-rw-r--r-- 1 14M máj 19 16:27 ufs910_neutrino_P217_CDK-rev953_HAL-rev589-next_NMP-rev7421-next.zip

-- Finished -----------------------------------------------------------


After flashing in box, works, but not screen...

Remote works, setup in vfd, but no video on scart...

[Audioniek]

You are not telling me in which box you have flashed this image. If it is your albis box, you will not have a picture indeed, because the UHS910 uses other .elf files than the UFS913 does.

Regards,

Audioniek.