Leider bootet das Image nicht.
Hab mir ein neues serial kabel besorgt. Hier nun das Crashlog:
Code:=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2019.02.03 00:01:42 =~=~=~=~=~=~=~=~=~=~=~= CPU 01 BCM74390011 PRID07252111 v1.23 RR:00000003 BFW seclib-1.10 BBL v1.0.1 AVS init... AVS init OK AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 10002b00 AVS load_code offset =00051000 LOADED AVS: overtemp mon ON single board select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 302b2500 MEMSYS-ALT SHMOO 02010000 BLD:11138 HW:hpf0_b1p6 V:2.1.0.0 MCB: FLEX AVS start:status=000000ff STB: Current voltage=000003b6(950) temperature=0000d6e9(55017) PV=00000365(869) MV=000003a6(934) AVS FW rev=30323478 [0.2.4.x] OK DDR0: !@ ffe0e780 <= ffe0db80 MEMSYS-0 @ f1100000 OK DDR1: =@ ffe0e780 <= ffe0db80 MEMSYS-1 @ f1180000 OK Sdram Scramble OTP = 0x00000001 Sdram Scramble OK select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 2025252b BFW load mode OTP = 0x0000000f bfw_hash_locked = 0x00000000 BFW key3 OK, BFW load OK BFW v4.1.5 INFO v00000001 COPY CODE... DONE MICH: disable success SSBL SEC: jtag debug status: 000000af PINMUX CACHE FLUSH OK MMU ON CACHE FLUSH OK _fbss 0705fd78 _ebss 070606f8 _end 07060718 HEAP @ 07100000 STACK @ 09200000 ARCH: CONFIG OK CLR BSS 0705fd78 to 070606f8 OK CLR SRAM OK CACHE FLUSH OK CPU CLKSET OK GO! [33;1m ,/ [0m [33;1m ,'/___,[0m BOLT v1.23 1846 LOCAL BUILD [33;1m.'__ ,' [0m (2018-11-20 12:14:18 jjs@ubuntu1604) [33;1m /,' [0m Copyright (C) 2018 Broadcom [33;1m /' [0m [0m Board: gbquad4k SYS_CTRL: product=72521, family=7439b1, strap=000000b2, otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000) otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020) RESET CAUSE: 0x000003 main_chip_input power_on (2 of 23 possible causes) CS0: SFDP SPI, 4MB, 64kB blocks, 64kB erase block, 256B pages RTS0: 0x1101004, 256 clients, ok RTS1: 0x1181004, 256 clients, ok BOX MODE: 2 CPU: 2x B15 [420f00f3] 1719 MHz SCB: 432 MHz DDR0 @ 1200MHz, DDR1 @ 1200MHz SPLASH: starting Loaded BMP: W=720 H=576 SPLASH: audio not present AVS: park check AVS: temperature monitoring enabled AVS: STB: V=0.945V, T=+56.965C, PV=0.869V, MV=0.934V, FW=30323478 [0.2.4.x] LCD: R61509V USB otp=00000040 AUTOBOOT [waitusb -t=3 -d='USB Disk' && batch usbdisk0:sysinit.txt] usb: resetting device on bus 1 hub 1 port 1[J USB: New high speed device connected to bus 1 hub 1 port 1[J USB device matching <USB Disk> not found! USB device matching <USB Disk> not found! SPLASH: starting Loaded BMP: W=720 H=576 SPLASH: audio not present *** STARTUP_1: File found . . . . Loader:raw Filesys:fat Dev:emmcflash0.boot File:STARTUP_3 Options:(null) Loading: . 177 bytes read Reading 4783264 bytes from zImage........... Starting program at 0x8000 (DTB @ 0x7624000) 32 bit direct boot... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.1.20-1.9 (oe-user@oe-host) (gcc version 8.2.0 (GCC) ) #1 SMP Wed Jan 23 10:50:57 UTC 2019 [ 0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: gbquad4k [ 0.000000] moving dtb from 0x0000000007624000 to 0x000000000098d748 [ 0.000000] bmem: Reserved 529 MiB at 0x000000001eb00000 [ 0.000000] bmem: Reserved 608 MiB at 0x000000009a000000 [ 0.000000] cma: Reserved 16 MiB at 0x0000000098c00000 [ 0.000000] Forcing write-allocate cache policy for SMP [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] PERCPU: Embedded 12 pages/cpu @dd1ab000 s16844 r8192 d24116 u49152 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523324 [ 0.000000] Kernel command line: root=/dev/mmcblk0p9 rootwait rw rootflags=data=journal libata.force=1:3.0G,2:3.0G,3:3.0G coherent_poll=2M vmalloc=525m bmem=529m@491m bmem=608m@2464m [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 889536K/2097152K available (6687K kernel code, 325K rwdata, 2188K rodata, 320K init, 213K bss, 1191232K reserved, 16384K cma-reserved, 422904K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xde800000 - 0xff000000 ( 520 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde300000 ( 483 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08b32b0 (8877 kB) [ 0.000000] .init : 0xc08b4000 - 0xc0904000 ( 320 kB) [ 0.000000] .data : 0xc0904000 - 0xc0955738 ( 326 kB) [ 0.000000] .bss : 0xc0958000 - 0xc098d748 ( 214 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xde802000, parent irq: 93) [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xde808000, parent irq: 64) [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xde80aa00, parent irq: 65) [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xde80c640, parent irq: 95) [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xde80e200, parent irq: 58) [ 0.000000] irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xfc40a700, parent IRQ(s): 2) [ 0.000000] irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xde810380, parent IRQ(s): 3) [ 0.000000] MCP: Enabling write pairing [ 0.000000] Architected cp15 timer(s) running at 27.00MHz (virt). [ 0.000000] clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x63a1e71a3, max_idle_ns: 440795203123 ns [ 0.000003] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 4398046511093ns [ 0.000010] Switching to timer-based delay loop, resolution 37ns [ 0.000338] Console: colour dummy device 80x30 [ 0.000356] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000) [ 0.000365] pid_max: default: 32768 minimum: 301 [ 0.000453] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000458] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000880] CPU: Testing write buffer coherency: ok [ 0.001087] CPU0: update cpu_capacity 1024 [ 0.001093] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001302] Setting up static identity map for 0x8480 - 0x84d8 [ 0.003953] CPU1: update cpu_capacity 1024 [ 0.003959] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.004023] Brought up 2 CPUs [ 0.004033] SMP: Total of 2 processors activated (108.00 BogoMIPS). [ 0.004038] CPU: All CPU(s) started in SVC mode. [ 0.004368] devtmpfs: initialized [ 0.013495] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0 [ 0.013720] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.015091] NET: Registered protocol family 16 [ 0.015735] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.021128] cpuidle: using governor ladder [ 0.030136] cpuidle: using governor menu [ 0.037327] No ATAGs? [ 0.037355] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.037361] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.037579] Broadcom Brahma-B15 readahead cache at: 0xde954478 [ 0.050644] brcmstb-gpio f040a600.gpio: Registered 5 banks (GPIO(s): 0-159) [ 0.050831] brcmstb-gpio f0417400.gpio: Registered 2 banks (GPIO(s): 160-223) [ 0.051172] SCSI subsystem initialized [ 0.051875] usbcore: registered new interface driver usbfs [ 0.051922] usbcore: registered new interface driver hub [ 0.051967] usbcore: registered new device driver usb [ 0.052037] Linux video capture interface: v2.00 [ 0.052113] pps_core: LinuxPPS API ver. 1 registered [ 0.052118] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.052136] PTP clock support registered [ 0.052599] Advanced Linux Sound Architecture Driver Initialized. [ 0.053646] Switched to clocksource arch_sys_counter [ 0.053863] FS-Cache: Loaded [ 0.059734] thermal thermal_zone0: failed to read out thermal zone (-22) [ 0.059841] NET: Registered protocol family 2 [ 0.060190] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.060213] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.060251] TCP: Hash tables configured (established 4096 bind 4096) [ 0.060294] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.060305] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.060408] NET: Registered protocol family 1 [ 0.060607] RPC: Registered named UNIX socket transport module. [ 0.060612] RPC: Registered udp transport module. [ 0.060615] RPC: Registered tcp transport module. [ 0.060618] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.060960] CPU PMU: Failed to parse /pmu/interrupt-affinity[0] [ 0.060991] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.061858] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.063211] NFS: Registering the id_resolver key type [ 0.063235] Key type id_resolver registered [ 0.063239] Key type id_legacy registered [ 0.063251] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.063257] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.063400] FS-Cache: Netfs 'cifs' registered for caching [ 0.063439] Key type cifs.spnego registered [ 0.063559] fuse init (API version 7.23) [ 0.064472] bounce: pool size: 64 pages [ 0.064507] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.064518] io scheduler noop registered [ 0.064526] io scheduler deadline registered [ 0.064538] io scheduler cfq registered (default) [ 0.064794] brcm-gisb-arb f0400000.gisb-arb: registered mem: de97c000, irqs: 261, 262 [ 0.065519] brcmstb-sata-phy f0458100.sata_phy: registered 2 port(s) [ 0.065922] brcm-pci f0460000.pcie: adjusting to legacy (broken) pcie DT [ 0.166108] brcm-pci f0460000.pcie: link down [ 0.166159] brcm-pci f0490000.pcie: adjusting to legacy (broken) pcie DT [ 0.266333] brcm-pci f0490000.pcie: link down [ 0.267761] brcmstb_memc f1102000.memc-ddr: registered [ 0.267802] brcmstb_memc f1182000.memc-ddr: registered [ 0.267994] brcm-waketimer f0417580.waketimer: registered, with irq 263 [ 0.268204] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.269407] console [ttyS0] disabled [ 0.269433] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A [ 1.006589] console [ttyS0] enabled [ 1.010465] f040a940.serial: ttyS1 at MMIO 0xf040a940 (irq = 108, base_baud = 5062500) is a 16550A [ 1.019757] f040a980.serial: ttyS2 at MMIO 0xf040a980 (irq = 109, base_baud = 5062500) is a 16550A [ 1.032107] loop: module loaded [ 1.036160] brcm-ahci f045a000.sata: controller can do ALPM, turning on CAP_ALPM [ 1.043586] brcm-ahci f045a000.sata: masking port_map 0x3 -> 0x3 [ 1.049646] brcm-ahci f045a000.sata: SSS flag set, parallel bus scan disabled [ 1.067658] brcm-ahci f045a000.sata: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.076639] brcm-ahci f045a000.sata: flags: 64bit ncq sntf stag pm clo pmp slum part [ 1.086145] scsi host0: brcm-ahci [ 1.089724] scsi host1: brcm-ahci [ 1.093200] ata1: FORCE: PHY spd limit set to 3.0Gbps [ 1.098267] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 91 [ 1.106196] ata2: FORCE: PHY spd limit set to 3.0Gbps [ 1.111257] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 91 [ 1.119192] brcm-ahci f045a000.sata: Broadcom AHCI SATA3 registered [ 1.126263] brcmstb_qspi f03e3400.spi: using bspi-mspi mode [ 1.131909] brcmstb_qspi f03e3400.spi: IRQ spi_l1_intr not found [ 1.137945] brcmstb_qspi: probe of f03e3400.spi failed with error -22 [ 1.144423] brcmstb_qspi f03e0920.qspi: using bspi-mspi mode [ 1.150577] m25p80 spi32766.0: found n25q032, expected m25p80 [ 1.156342] m25p80 spi32766.0: n25q032 (4096 Kbytes) [ 1.161336] 5 ofpart partitions found on MTD device spi32766.0 [ 1.167180] Creating 5 MTD partitions on "spi32766.0": [ 1.172329] 0x000000000000-0x000000100000 : "flash0.bolt" [ 1.178252] 0x000000100000-0x000000110000 : "flash0.macadr" [ 1.184272] 0x000000110000-0x000000120000 : "flash0.nvram" [ 1.190193] 0x000000120000-0x000000130000 : "flash0.devtree" [ 1.196287] 0x000000000000-0x000000400000 : "flash0" [ 1.202308] libphy: Fixed MDIO Bus: probed [ 1.206866] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001 [ 1.212762] bcmgenet f0b00000.ethernet: failed to get enet-mux clock [ 1.230652] ata1: SATA link down (SStatus 0 SControl 320) [ 1.236643] libphy: bcmgenet MII bus: probed [ 1.261477] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k [ 1.267328] e1000e: Copyright(c) 1999 - 2014 Intel Corporation. [ 1.273456] xhci-brcm: xHCI BRCM driver [ 1.292132] xhci-brcm f0471000.xhci_v2: xHCI Host Controller [ 1.297915] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1 [ 1.305990] xhci-brcm f0471000.xhci_v2: hcc params 0x0250f17d hci version 0x100 quirks 0x00010090 [ 1.314896] xhci-brcm f0471000.xhci_v2: irq 149, io mem 0xf0471000 [ 1.321529] hub 1-0:1.0: USB hub found [ 1.325316] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 1.332584] xhci-brcm f0471000.xhci_v2: xHCI Host Controller [ 1.338347] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2 [ 1.346252] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.354674] ata2: SATA link down (SStatus 0 SControl 320) [ 1.354721] hub 2-0:1.0: USB hub found [ 1.354744] hub 2-0:1.0: 2 ports detected [ 1.355143] ehci-brcm: EHCI BRCM driver [ 1.355256] ehci-brcm f0470300.ehci_v2: EHCI Host Controller [ 1.355367] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3 [ 1.365493] ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300 [ 1.370643] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00 [ 1.371109] hub 3-0:1.0: USB hub found [ 1.371149] hub 3-0:1.0: 1 port detected [ 1.371409] ehci-brcm f0470500.ehci_v2: EHCI Host Controller [ 1.371513] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4 [ 1.381662] ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500 [ 1.387641] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00 [ 1.388079] hub 4-0:1.0: USB hub found [ 1.388119] hub 4-0:1.0: 1 port detected [ 1.388451] ohci-brcm: OHCI BRCM driver [ 1.388549] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller [ 1.388699] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 5 [ 1.388799] ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400 [ 1.444097] hub 5-0:1.0: USB hub found [ 1.444136] hub 5-0:1.0: 1 port detected [ 1.444390] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller [ 1.444491] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 6 [ 1.444584] ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600 [ 1.499048] hub 6-0:1.0: USB hub found [ 1.502900] hub 6-0:1.0: 1 port detected [ 1.507121] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.513683] ehci-pci: EHCI PCI platform driver [ 1.518188] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.524397] ohci-pci: OHCI PCI platform driver [ 1.528976] usbcore: registered new interface driver usb-storage [ 1.535225] mousedev: PS/2 mouse device common for all mice [ 1.541139] i2c /dev entries driver [ 1.545280] IR NEC protocol handler initialized [ 1.549834] IR RC5(x/sz) protocol handler initialized [ 1.554900] IR RC6 protocol handler initialized [ 1.559444] IR JVC protocol handler initialized [ 1.563987] IR Sony protocol handler initialized [ 1.568617] IR SANYO protocol handler initialized [ 1.573334] IR Sharp protocol handler initialized [ 1.578050] IR MCE Keyboard/mouse protocol handler initialized [ 1.583911] IR XMP protocol handler initialized [ 1.589135] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver [ 1.597326] brcmstb-cpufreq f03e257c.cpu-clk-div: registered [ 1.603213] sdhci: Secure Digital Host Controller Interface driver [ 1.609412] sdhci: Copyright(c) Pierre Ossman [ 1.613783] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.620685] sdhci-brcmstb f03e0000.sdhci: No vmmc regulator found [ 1.626799] sdhci-brcmstb f03e0000.sdhci: No vqmmc regulator found [ 1.663649] mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using ADMA [ 1.672204] sdhci-brcmstb f03e0200.sdhci: No vmmc regulator found [ 1.678315] sdhci-brcmstb f03e0200.sdhci: No vqmmc regulator found [ 1.690771] usb 2-2: new SuperSpeed USB device number 2 using xhci-brcm [ 1.710905] hub 2-2:1.0: USB hub found [ 1.714644] mmc1: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA [ 1.714813] hidraw: raw HID events driver (C) Jiri Kosina [ 1.715043] usbcore: registered new interface driver usbhid [ 1.715044] usbhid: USB HID core driver [ 1.723249] Initializing XFRM netlink socket [ 1.735111] NET: Registered protocol family 10 [ 1.749742] usb 4-1: new high-speed USB device number 2 using ehci-brcm [ 1.749753] NET: Registered protocol family 17 [ 1.749773] NET: Registered protocol family 15 [ 1.749924] Key type dns_resolver registered [ 1.750013] Registering SWP/SWPB emulation handler [ 1.756026] ALSA device list: [ 1.756028] No soundcards found. [ 1.784864] hub 2-2:1.0: 4 ports detected [ 1.798478] Waiting for root device /dev/mmcblk0p9... [ 1.853269] mmc1: MAN_BKOPS_EN bit is not set [ 1.863971] mmc1: new high speed MMC card at address 0001 [ 1.869650] mmcblk0: mmc1:0001 004GE0 3.69 GiB [ 1.874260] mmcblk0boot0: mmc1:0001 004GE0 partition 1 2.00 MiB [ 1.880250] mmcblk0boot1: mmc1:0001 004GE0 partition 2 2.00 MiB [ 1.886240] mmcblk0rpmb: mmc1:0001 004GE0 partition 3 512 KiB [ 1.894794] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 [ 1.904081] EXT3-fs (mmcblk0p9): error: couldn't mount because of unsupported optional features (240) [ 1.913684] EXT4-fs: Warning: mounting with data=journal disables delayed allocation and O_DIRECT support! [ 1.913805] hub 4-1:1.0: USB hub found [ 1.914192] hub 4-1:1.0: 4 ports detected [ 1.979422] EXT4-fs (mmcblk0p9): recovery complete [ 1.985157] EXT4-fs (mmcblk0p9): mounted filesystem with journalled data mode. Opts: data=journal [ 1.994079] VFS: Mounted root (ext4 filesystem) on device 179:9. [ 2.000435] devtmpfs: mounted [ 2.003555] Freeing unused kernel memory: 320K (c08b4000 - c0904000) INIT: version 2.88 booting [ 2.174983] Adding 539644k swap on /dev/mmcblk0p10. Priority:-1 extents:1 across:539644k SS cat: can't open '/sys/block/mmcblk0/device/model': No such file or directory [ 2.339719] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. cat: can't open '/sys/block/mmcblk0/device/model': No such file or directory mkdir: can't create directory '/media/mmcblk0p1': File exists [ 2.513295] EXT4-fs (mmcblk0p5): warning: maximal mount count reached, running e2fsck is recommended [ 2.523157] EXT4-fs (mmcblk0p5): recovery complete [ 2.527985] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null) cat: can't open '/sys/block/mmcblk0/device/model': No such file or directory mkdir: can't create directory '/media/mmcblk0p1': File exists [ 2.631850] EXT4-fs (mmcblk0p7): recovery complete [ 2.636678] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null) cat: can't open '/sys/block/mmcblk0/device/model': No such file or directory mkdir: can't create directory '/media/mmcblk0p1': File exists [ 2.758987] EXT4-fs (mmcblk0p9): re-mounted. Opts: nodelalloc,data=journal grep: /sys/devices/platform/Fixed: No such file or directory grep: MDIO: No such file or directory grep: bus.0/modalias: No such file or directory /dev/dvb/adapter0/video0: No such file or directory vm.dirty_writeback_centisecs = 300 vm.dirty_background_ratio = 1 vm.dirty_ratio = 60 [ 3.150834] random: dd urandom read with 15 bits of entropy available ALSA: Restoring mixer settings... /etc/rcS.d/S39ddbootup: line 2: /proc/stb/lcd/mode: No such file or directory touch: /dev/dbox/lcd0: No such file or directory /etc/rcS.d/S39ddbootup: line 4: /proc/stb/info/gbmodel: No such file or directory /usr/sbin/alsactl: load_state:1735: No soundcards found... Starting gigablue-platform-util...
Bin gespannt auf das HDMU Image wenn es dann mal läuft.