hs7429
The uImage file loads and mounts same .ird And shows on the recive display rd then shows error
hs7429
The uImage file loads and mounts same .ird And shows on the recive display rd then shows error
Geändert von sadaghiani (22.10.2019 um 20:47 Uhr)
Hi Audioniek
Thank you for your new images. I've tested the USB version ( hs7819_Audioniek_enigma2_gst-epl3_USB_P217_CDK-rev1280.zip)for the hs7819 receiver.
After starting, the VFD-Display shows Boot and the receiver not started.
@sadaghiani: I have replaced the image file with a tested new one. You were right: the file was not OK.
@setifstar: I will have a look.
Regards,
Audioniek.
Receivers: Rebox: RE-4000, 8000, 9000, 2200, 2210, 2220, 4200, 4210, 4220, 8220, 8500, SAB Unix Triple, Golden Media Spark TripleX, Amiko Alien 2+, Sogno Spark Revolution, Kathrein UFS910(1 & 14W)/912/913/922(CX24116 & AVL2108 tuners), Vizyon revolution 820HD PVR, AB IPBox 91HD/9000HD/9000HD rev.2, Xsarius Alpha HD10, nBox BKSA/BSLA/BXZB/BZZB, Vitamin HD 5000
Sats: Astra 1, 2 & 3, Hotbird
Main activity: building my own E2 images for Fortis receivers
7429
err 0x70
-------------------
transcend 8g
jetflash 350
-------------------
The kernel settings (uimage) seem to be incorrect
Geändert von sadaghiani (27.10.2019 um 09:59 Uhr)
@setifstar:If the display stays at boot, the USB kernel starts but cannot read rootfs.img. In my experience it is very hard to find a USB stick that works 100% of the time. Usually I have more success after several power ups: sooner or later the kernel does not switch off the USB power and the whole lot starts up. Use older USB sticks of 512 MByte to 2Gbyte in capacity to get the best results.
@sadaghiani: If have tested the flash version and it flashes perfectly, it also starts up the way it is intended. My gut feeling says you are trying to flash the USB uImage into flash memory: this will not fit and indeed yield a correct Err 0x70. Please read the installation instructions carefully.
Regards,
Audioniek.
Receivers: Rebox: RE-4000, 8000, 9000, 2200, 2210, 2220, 4200, 4210, 4220, 8220, 8500, SAB Unix Triple, Golden Media Spark TripleX, Amiko Alien 2+, Sogno Spark Revolution, Kathrein UFS910(1 & 14W)/912/913/922(CX24116 & AVL2108 tuners), Vizyon revolution 820HD PVR, AB IPBox 91HD/9000HD/9000HD rev.2, Xsarius Alpha HD10, nBox BKSA/BSLA/BXZB/BZZB, Vitamin HD 5000
Sats: Astra 1, 2 & 3, Hotbird
Main activity: building my own E2 images for Fortis receivers
I mean the usb version Which has this error
I haven't tested the Flash version yet
I understand now. Probably your USB stick is not recognized and/or USB boot is switched off. The receiver will then boot from flash, but that is corrupt for some reason, leading to Err 0x70 (Kernel File system error).
The sequence of displays on the front panel should be:
- L 7.36 or L 7.37
- SCAN USB (check for an USB stick with uImage on it)
- R 0 (if found read and start uImage from USB)
- BOOT (uImage is started and tries to mount rootfs.img)
- .... (E2 mesages)
If SCAN USB does not appear, USB boot is off.
Regards,
Audioniek.
Receivers: Rebox: RE-4000, 8000, 9000, 2200, 2210, 2220, 4200, 4210, 4220, 8220, 8500, SAB Unix Triple, Golden Media Spark TripleX, Amiko Alien 2+, Sogno Spark Revolution, Kathrein UFS910(1 & 14W)/912/913/922(CX24116 & AVL2108 tuners), Vizyon revolution 820HD PVR, AB IPBox 91HD/9000HD/9000HD rev.2, Xsarius Alpha HD10, nBox BKSA/BSLA/BXZB/BZZB, Vitamin HD 5000
Sats: Astra 1, 2 & 3, Hotbird
Main activity: building my own E2 images for Fortis receivers
- L 7.36 or L 7.37 ok
- SCAN USB ok
- R 0 ok
- BOOT fault - stop on boot
- ...................................
- transcend 2g
Geändert von sadaghiani (28.10.2019 um 15:00 Uhr)
HS 7429
-------------------------
I installed the flash version
Congratulations on this project
And thank you
-------------------------
So far everything looks great
Geändert von sadaghiani (28.10.2019 um 21:29 Uhr)
HS 7819
-------------------------
When I want installed the flash version :Error 20 or en :20 on front vfd
Geändert von setifstar (29.10.2019 um 18:51 Uhr)