Hi All,

Had a few problems with my serial cable so didn't have an opportunity to capture a log of failure. Missed the 1st part of the log due to not setting the scrollback properly ..but looks like a possible modules issue ?

usbcore: registered new interface driver usbfsusbcore: registered new interface driver hub
usbcore: registered new device driver usb
DMA: Registering DMA API.
Switching to clocksource TMU1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de)..
Slow work thread pool: Starting up
Slow work thread pool: Ready
NTFS driver 2.1.29 [Flags: R/O].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
JFS: nTxBlock = 905, nTxLock = 7244
msgmni has been set to 226
io scheduler noop registered
io scheduler anticipatory registered (default)
lirc_dev: IR Remote Control driver registered, major 61
lirc-stm: probe found data for platform device lirc-stm
lirc-stm: STM LIRC plugin using IRQ 125 in IR mode
lirc_dev: lirc_register_driver: sample_rate: 0
STMicroelectronics LIRC driver initialized.
STMicroelectronics ASC driver initialized
stm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-asc
stm-asc.1: ttyAS1 at MMIO 0xfd033000 (irq = 120) is a stm-asc
loop: module loaded
Davicom DM9161E: Registered new driver (0x0181b880)
Davicom DM9161A: Registered new driver (0x0181b8a0)
Davicom DM9131: Registered new driver (0x00181b80)
RTL821x Gigabit Ethernet: Registered new driver (0x001cc912)
STe100p: Registered new driver (0x1c040011)
STe101p: Registered new driver (0x00061c50)
Micrel KS8001 or KS8721: Registered new driver (0x0022161a)
Micrel KSZ9021 Gigabit PHY: Registered new driver (0x00221611)
Micrel KS8737: Registered new driver (0x00221720)
Micrel KS8041: Registered new driver (0x00221510)
Micrel KS8051: Registered new driver (0x00221550)
STMMAC driver:
platform registration...
done!
PMT module supported
DWMAC1000 - user ID: 0x10, Synopsys ID: 0x33
Enhanced descriptor structure
PARSE CMDLINE: 00:00:00:00:00:00
ETHADDR: 00:00:00:00:00:00
no valid MAC address;please, use ifconfig or nwhwconfig!
eth0 - (dev. name: stmmaceth - id: 0, IRQ #134
IO base addr: 0xfd110000)
STMMAC MII Bus: probed
eth0: PHY ID 0007c0f1 at 2 IRQ 0 (0:02) active
nwhw_config: (eth0) setting mac address: 30:00:0A:00C6
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
stm_usb_probe: usb_phy_clk clock not found for stm-usb.0
stm-ehci stm-ehci.0: st-ehci
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: stm-ohci
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
stm_usb_probe: usb_phy_clk clock not found for stm-usb.1
stm-ehci stm-ehci.1: st-ehci
stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3
stm-ehci stm-ehci.1: irq 143, io mem 0xfeaffe00
stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
stm-ohci stm-ohci.1: stm-ohci
stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4
stm-ohci stm-ohci.1: irq 142, io mem 0xfeaffc00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Linux video capture interface: v2.00
sh_tmu: TMU0 kept as earlytimer
sh_tmu: TMU1 kept as earlytimer
STMicroelectronics - Coprocessors st231 Init
st231.0 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xbf000000 size 0x00400000
cop. addr 0x40000000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
st231.1 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xbf400000 size 0x00400000
cop. addr 0x40400000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
DMA: Registering fdma_dmac.0 handler (16 channels).
IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma.0: firmware: using built-in firmware fdma_STx7105_0.elf
DMA: Registering fdma_dmac.1 handler (16 channels).
platform fdma_dmac.0: SLIM hw 0.0, FDMA fw 2.1
IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma.1: firmware: using built-in firmware fdma_STx7105_1.elf
stm-rng hardware driver 1.0 configured
platform fdma_dmac.1: SLIM hw 0.0, FDMA fw 2.5
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
#0: STMicroelectronics STx7105 cut 4 SOC audio subsystem
TCP cubic registered
NET: Registered protocol family 17
NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 512MiB 3,3V 8-bit)
stm-nand-flex: Using boot partition name [uboot] (from kernel config)
cmdlinepart partition parsing not available
Creating 7 MTD partitions on "stm-nand-flex.0":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000b00000 : "Spark kernel"
0x000000b00000-0x000001200000 : "Reserve0"
0x000001200000-0x000001400000 : "Reserve1"
0x000001400000-0x000018000000 : "Spark Userfs"
0x000018000000-0x000018800000 : "E2 kernel"
0x000018800000-0x00001ff00000 : "E2 Userfs"
stm-nand-flex: Found BOOT parition[uboot], updating ECC paramters
boot-ECC 0x00000000->0x00100000
stmmac: Rx Checksum Offload Engine supported
TX Checksum insertion supported
IP-Config: Complete:
device=eth0, addr=172.100.100.249, mask=255.255.0.0, gw=172.100.100.174,
host=Enigma2, domain=, nis-domain=(none),
bootserver=172.100.100.174, rootserver=172.100.100.174, rootpath=
Empty flash at 0x0229c170 ends at 0x0229c800
VFS: Mounted root (jffs2 filesystem) on device 31:6.
Freeing unused kernel memory: 132k freed
INIT: version 2.86 booting
PHY: 0:02 - Link is Up - 100/Full
init frontpanel
Fulan front panel driver
VfdType = 2
CpuType = 2
DisplayInfo = 1
scankeyNum = 8
swMajorVersion = 1
swSubVersion = 10
input: fulan front panel buttons as /devices/virtual/input/input0
[simu_button] initializing ...
[simu_button] allocating and registering button device
input: TDT RC event driver as /devices/virtual/input/input1
insmod: can't insert '/lib/modules/encrypt.ko': No such file or directory
Mount /dev in tmpfs
Copying device nodes to /dev
Starting portmap daemon....
Loading autofs
Starting autofs
Starting DEBUG Interface
Mounting local filesystems...
mount: mounting /dev/sda1 on /hdd failed: No such device or address
Cleaning /tmprmdir: './autoiagxTS': Device or resource busy
rmdir: './autoMfEZww': No such file or directory
find: ./autoW4nCuT: No such file or directory
find: ./autoGPTxPw: No such file or directory
.
Hostname: spark7162.
starting telnetd
init stmfb
stmcore-display: using HDMI hotplug
stmcore-display: STi7105 display: probed
device probe found 2 display pipelines
requesting frm: 'component.fw', c11dd764/875c7c50
stm-awg: firmware: requesting component.fw
frm 'component.fw' successfully loaded
requesting frm: 'fdvo0.fw', c11dd764/875c7fd0
stm-awg: firmware: requesting fdvo0.fw
loading frm: 'fdvo0.fw' failed: -2
stmfb: fb0 parameters = "1280x720-32@50:15mal:yuv:yuv"
stmfb: fb1 parameters = "<NULL>"
LOADING MODULES
load a firmware
copLoadFile (file /boot/audio.elf)
ustslave: Kernel Version: 24
base_address 0x40400000
seeking to d0000000
seeking to d0005f00
seeking to d0012320
seeking to d001aa20
seeking to d0173100
seeking to d0173138
seeking to d0173170
seeking to d01b9058
seeking to d01b9060
seeking to d01b9068
seeking to d01b9070
seeking to d01d0920
seeking to d01d0a00
load v firmware
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x40000000
seeking to d0000000
seeking to d004e020
seeking to d00f8378
seeking to d00f83b0
seeking to d00f83e8
seeking to d010ce98
seeking to d010cea4
seeking to d010ceb0
seeking to d012ed90
seeking to d012cd74
seeking to d012ee00
init embx