ok, you have install to sda1, and you have try boot with button 5?
still no luck loading from sda1.
i have tried several times.
the multiboot option is definitely no.5
i have the following partitions set up
mount
rootfs on / type rootfs (rw)
/dev/root on / type squashfs (ro)
none on /tmp type tmpfs (rw)
none on /dev type tmpfs (rw)
none on /mnt type tmpfs (rw)
/dev/mtdblock4 on /var type jffs2 (rw)
none on /tmp/mqueue type mqueue (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
tmpfs on /dev/shm type tmpfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
/dev/sda2 on /mnt/usb type ext2 (rw)
/dev/sda1 on /mnt/usb/usb0 type ext2 (rw,sync)
/dev/sda2 on /mnt/usb/usb1 type ext2 (rw)
/dev/sda3 on /mnt/usb/usb2 type ext2 (rw,sync)
[SifTeam]$
i have installed the image on mnt/usb/usb0 and can see all the image files when viewing from ftp
i just cant get the e2 image to boot.
it looks like i will just have to stick to 1 image on the stick
h
ok i found a serial lead and tried to boot twice from sda1 then loaded from flash .
here is the logfile from putty
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
that´s the problem, i think.
try this:
then, boot with 1 or 2, please a with serial log again.Code:fw_setenv menu_1 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda1 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA1-USB;boot' fw_setenv menu_2 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 1:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda1 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA1-USB;boot'
still wont boot from 1 or 2 front panel says 'sda1 usb' each time
here is log
Bad Magic Number
this is the problem if you format the part with mkfs.ext2 /dev/sda1 withou -I128...
please try to umount and format new
umount /dev/sda1
mkfs.ext2 -L MINI1 -I128 -b4096 /dev/sda1
mount /dev/sda1 ...
ftp
cd /mnt...
tar xvzf HDMU*.tar.gz
ok i have tried that and still wont boot from sda1 it just keeps trying.
i dont know what is wrong
thx
h
ok,the stick is now ok, the kernel was load and started, but not the image, please try this bootarg.
the last test was button 1?Code:fw_setenv menu_1 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sdb1 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDB1-USB;boot'
I have changed the code above then try to boot from 2 = sda1 usb then 1= sdb1 usb then 5 = e2 sda1 usb but still the same.
i tried several times deleting and re-partitioning the usb and tried another usb but no luck
h