which image do you try to install?
I see only a P207 Image, try an other Image, p209 for IP900 or p211 for IP910
I have been able to load pkt e2 p211 image I will get it set up then I assume I can install 2 other images to usb1 & usb2 to see which one I like best I would like to get my external e-data hdd working if possible along with scart had. I may be able to use my 500gb usb drive to be partitioned for images and recordings?
Thanks for the help
H
ok sorry to be a nuisance but i think my best option is to partition my 500gb usb hdd and use it to have several images on and also act as a hdd for recordings.
i am having a bit of trouble formatting it maybe you could give me these steps then i should be able to partition and load images as before on 16gb usb stick.
this is the mount info
SifTeam]$ mount
rootfs on / type rootfs (rw)
/dev/root on / type squashfs (ro)
none on /tmp type tmpfs (rw)
none on /dev type tmpfs (rw)
none on /mnt type tmpfs (rw)
/dev/mtdblock4 on /var type jffs2 (rw)
none on /tmp/mqueue type mqueue (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
tmpfs on /dev/shm type tmpfs (rw)
usbfs on /proc/bus/usb type usbfs (rw)
/dev/sda2 on /var/media type ext3 (rw,data=writeback)
[SifTeam]$
thanks
h
Disk /dev/sda: 500.0 GB, 500074283008 bytes
255 heads, 63 sectors/track, 60797 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 32 257008+ 83 Linux
/dev/sda2 33 60797 488094862+ 83 Linux
[SifTeam]$
fdisk /dev/sda
delete 2
delete 1
n for create new part,
p primary
1
start 1
stop 60647
n
p
2
enter
60697
n
p
3
enter
60747
n
p
4
enter
enter
w write to exit
reboot
mkfs.ext2 -L RECORD /dev/sda1
mkfs.ext2 -L MINI2 -I128 -b4096 /dev/sda2
mkfs.ext2 -L MINI3 -I128 -b4096 /dev/sda3
mkfs.ext2 -L MINI4 -I128 -b4096 /dev/sda4
reboot
ftp image to one MINI Part(2,3 or4)
cd /mnt...
tar xvzf *.*
Code:fw_setenv menu_1 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:2 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda2 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA2-USB;boot' fw_setenv menu_2 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:3 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda3 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA3-USB;boot' fw_setenv menu_3 'setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:4 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 root=/dev/sda4 rw init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask:cuberevo:eth0:off mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr";setenv bootcmd "run bootusb";saveenv;front_puts SDA4-USB;boot'
thanks i will try this
im having trouble getting the device to write the new allocation table.
after following all the steps is says error 16 the device or resource is busy and on reboot the new partitions are not set?