Danke!
Ja, chmod habe ich schon gesehen.
Danke!
Ja, chmod habe ich schon gesehen.
______________________
Hans
Amiko Alien 2+, AzBox Me, Golden Interstar XPEED Lx1, Edision Optimuss OS1+, Mut@nt HD1500, Red Eagle Singlebox, Spycat
TV - Hisense Ulra HD
Astra 19,2° Unicable-LNB
Diese Meldung erscheint nur, wenn ich den Tool Pfad auf meinen Benutzerdefinierten Pfad stelle. Wenn ich die movie Partition wähle und die HDD an ist, kommt die Meldung nicht. Unter /AT_MORLY sind auf der HDD auch noch einige *.bin und *.sh, die sind auf dem USB Stick nicht.
Ich nehme an Du meinst einen File Browser. Den findest Du für Flash Images unter Flash, für USB Images unter Disks/MB bei Manage Partitions. Wenn da nichts erscheint, mußt Du oben Show Partition Content auswählen.
I think spark needs a USB Image, and you tried to install this into the flash. You have to use the Image Install Wizard in the Disks/MB Tab.
Edit: Sorry, I thought Spark is only USB, so you can use both, USB and Flash.
Spark uses flash, that is what I always use. I have never used USB.
Any solution to get the tool to work?
- - - Aktualisiert - - -
[QUOTE = morly; 79472] Did the intentionally not inside - if you uploading and downloading mean, everything else allows the FTP browser anyway --- Updated --- When you choose to install backups or plugins the box is waiting for the initial reboot (so the new image gets started) to do the installation. except The howto will be published in the manual section, soon [/ QUOTE]
After clicking on flash in the tool the box gets stuck in "Booting" and the tool keeps waiting for the initial reboot
Take a look at morly's Post #53.
Perhaps this will help.
Did the intentionally not inside - if you uploading and downloading mean, everything else allows the FTP browser anyway --- Updated --- When you choose to install backups or plugins the box is waiting for the initial reboot (so the new image gets started) to do the installation. except The howto will be published in the manual section, soon
I'm trying again. I backup all plugins I want to install after the flashing, then hit flash and still going. See screenshotFlash.jpg
The 4 tools keep flashing like something is happening but the box just stop in "Boot"
The tool waits until the box gets disconnected and then reconnected again.
This usually happens after your enter the IP in the install wizard of the image. Until then don't touch the AT
"Every Setback is a Set Up for a Comeback"
I can only see waiting for reconnection on IP address 192.168.0.13 but it doesn't reconnect
Where is the install wizard?
How do you enter the IP in the install wizard?
I was only prompted to select the image file
Geändert von cga (09.06.2014 um 20:02 Uhr)
ok - once more - the following is happening:
you can add/activate to install your plugins after flashing, and/or to install backups (from rules) - if one of this is the case, the tool must wait until the newly flashed image was booted
Progress:
- AT gets connected to box, flashing procedure activated
- AT starts flashing, the files get transferred to the box and flashing starts automatically (takes 1-2 minutes)
- AT automatically reconnects the box and says "waiting for re-connection"
- On TV the newly installed flash image starts with the "initial install wizard" (where you choose the language, network settings, transponder, ...)
- As soon as the network got configured (with the old IP) the AT connects to the box
- When the box was found the plugins get installed and the AT says "FLASHING DONE"
"Every Setback is a Set Up for a Comeback"
Once again
I don't get anything on the TV
In the front of the receiver says "Boot" and I don't get any wizard, it just mess up the previous image installed
@cga, please start the AT, go to the Flashing Tool, deactivate the first two (plugins and backup),
start flashing and choose the right spark flash image.
how long does the flashing take until the automatic reboot of the box?
does the newly flashed image boot?
if nothing happens after the box says "disconnected" please switch off your box and on again (after ~20 seconds)
"Every Setback is a Set Up for a Comeback"
Maybe I'm using the wrong image
This is the image I'm using HDMU_12293_E2_spark_214_git_5767_nodebug_mix_Flash .zip but I can see you have images there
Is this the right image?
I just put my image back with Spark. I want to do it again but I want to make sure this is the right image
HDMU_12293_E2_spark_214_git_5767_nodebug_mix_USB.t ar.gz.md5 25-May-2014 03:17 90.00 B HDMU_12293_E2_spark_214_git_5767_nodebug_mix_USB.t ar.gz 25-May-2014 03:06 38.95 MB HDMU_12293_E2_spark_214_git_5767_nodebug_mix_Flash .zip.md5 25-May-2014 03:07 89.00 B HDMU_12293_E2_spark_214_git_5767_nodebug_mix_Flash .zip
Geändert von cga (09.06.2014 um 20:34 Uhr)