Hallihallo!
Bitte um Nachsicht, bin Anfänger...
Ich habe folgendes Problem, was schon mal vor einem Jahr vom meinem Händler repariert wurde. Jetzt will ich aber mal...
- Enigma startet plötzlich nicht mehr. Es wird nur noch "boot" angezeigt. Terminal meldet dann und bleibt stehen:
Code:Image Type: SuperH Linux Kernel Image (gzip compressed) Data Size: 2175496 Bytes = 2.1 MiB Load Address: 80801000 Entry Point: 80802000 ## Booting image at 80000000 ... Image Name: Linux-2.6.32.59_stm24_0211 Image Type: SuperH Linux Kernel Image (gzip compressed) Data Size: 2175496 Bytes = 2.1 MiB Load Address: 80801000 Entry Point: 80802000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK found phy at addres = 2 stmac_phy_get_addr(): id1 = 0x0, id2 = 0x8201 stb_id = 90800bf7 Starting kernel console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw in it=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 rw ip=172.1 00.100.249:172.100.100.174:172.100.100.174:255.255.0.0:LINUX7109:eth0:off bigphy sarea=6000 stmmaceth=msglvl:0,phyaddr:2,watchdog:5000 nwhwconf=device:eth0,hwadd r:24:00:08:00:0B:F7 Manufacture=Spark-Project STB_ID=09:00:08:00:00:0B:F7 - 0x00 000000 - 0 ...- Spark startet problemlos!
- Update mit USB-Stick (viele verschiedene versucht, FAT und FAT32) klappt nicht, nach "Force" kommt "Fact" und bleibt stehen. Kein 770!
- Terminal meldet dann und bleibt stehen:
Code:U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel DRAM: 128 MiB NOR: 8 MiB NAND: 512 MiB In: serial Out: serial Err: serial IdentID : 09 00 08 00 00 0b f7 Hit ESC to stop autoboot: 5 Force command mode:Select boot (current boot system : enigma2): 1. spark(up key) 2. enigma2(down key) 3. RS232 Upgrade u-boot(left key) 4. Force into factory mode(right key) Input Select: Force Factory mode (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices...- Das Flashen über TFTP:
Code:Force command mode:Select boot (current boot system : enigma2): 1. spark(up key) 2. enigma2(down key) 3. RS232 Upgrade u-boot(left key) 4. Force into factory mode(right key) Input Select: Force Factory mode (Re)start USB... USB: scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Can't read from device 0 ** ** Unable to use usb 0:1 for fatload ** Warning: MAC addresses don't match: HW MAC address: FF:FF:FF:FF:FF:FF "ethaddr" value: 00:80:E1:12:06:38 Using MAC Address 00:80:E1:12:06:38 *** ERROR: `ethaddr' not set- Die bootargs habe ich neu gesetzt wie in der angehängten txt
Was könnte ich noch versuchen? Was mache ich noch falsch?
Danke und Grüße,
wayne