Gab es nicht boxen wo man den seriellen Output erst aktivieren musste?
Wo müsste man den Output dann wie aktivieren?
Versuch mal mit dem mat die bootargs auszulesen, vielleicht ist das so wie bei der spark, bitte aber erstmal die bootargs hier posten bevor du was veränderst.
http://www.hdmedia-universe.com/boar...ead.php?t=3967
Edit: ist schön in deinem log zu sehen, starte Kernel at ttyAS1, das muss auf 0 dann kommt mehr.
Hmm, das Tools lässt mich die Bootargs leider nicht auslesen oder bearbeiten. Wie kann ich denn ttyAS1 dann ändern (was auch immer das ist )?
Unknown box type: box type can not be read - wrong configuration
Unsupported box type - starting MAT with limited support
Edit: Ah, tty - http://www.wikiwand.com/de/TTY-Schnittstelle
Geändert von mb04fwe3 (05.02.2015 um 12:07 Uhr)
Okay, danke für den Hinweis. Liest sich dann erstmal so:
Was genau müsste geändert werden? Und wie?Code:#Bootargs Morly's SH4 STB Admin Tool from: Do Feb 5 2015bootdelay=1 baudrate=115200 autoload=n board=Twin ethaddr=00:1E:B8:01:3C:0A ipaddr=192.168.178.28 netmask=255.255.255.0 gatewayip=192.168.178.1 hdd=1 mtdargs=set bootargs console=ttyAS1,115200 nwhwconf=device:eth0,hwaddr:${ethaddr} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask} root=/dev/mtdblock3 rootfstype=squashfs bigphysarea=4060 stmmaceth=msglvl:0,watchdog:4000,rxsize:16 loglevel=0 usbargs=set bootargs console=ttyAS1,115200 nwhwconf=device:eth0,hwaddr:${ethaddr} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${board}:eth0:off root=/dev/sd${sdx}${par} rw mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=5 init=/bin/dev sdxconf=if test $hdd -eq 0 -a $usb -eq 0; then set sdx a; elif test $hdd -eq 1 -a $usb -eq 1; then set sdx c; else set sdx b; fi usbconf=usb reset; sleep 3; run sdxconf; run usbargs usbload=if fatload usb $usb:1 a5000000 /uImage$par; then; elif ext2load usb $usb:$par a5000000 /boot/uImage; then; fi backup=erase a0300000 a1ffffff; cp.b a5000000 a0300000 1d00000; run mtdargs; bootm a0300000 usbtool=if fatload usb 0:1 a5000000 /uImage; then bootm a5000000; elif fatload usb 0:1 a5000000 /uBackup_${board}; then run backup; fi; run mtdargs; bootm a0300000 bootcmd=bootmenu $menutimeout $default bootdesc_0=---Flash--- bootcmd_0=run mtdargs; bootm a0300000 bootdesc_1=--USB1 P1-- bootcmd_1=set usb 0; set par 1; run usbconf; run usbload; bootm a5000000 bootdesc_2=--USB1 P2-- bootcmd_2=set usb 0; set par 2; run usbconf; run usbload; bootm a5000000 bootdesc_3=--USB1 P3-- bootcmd_3=set usb 0; set par 3; run usbconf; run usbload; bootm a5000000 bootdesc_4=--USB1 P4-- bootcmd_4=set usb 0; set par 4; run usbconf; run usbload; bootm a5000000 bootdesc_5=--USB2 P1-- bootcmd_5=set usb 1; set par 1; run usbconf; run usbload; bootm a5000000 bootdesc_6=--USB2 P2-- bootcmd_6=set usb 1; set par 2; run usbconf; run usbload; bootm a5000000 bootdesc_7=--USB2 P3-- bootcmd_7=set usb 1; set par 3; run usbconf; run usbload; bootm a5000000 bootdesc_8=--USB2 P4-- bootcmd_8=set usb 1; set par 4; run usbconf; run usbload; bootm a5000000 bootdesc_9=--USB 112-- bootcmd_9=set usb 0; set par 2; run usbconf; run usbtool menutimeout=3000 default=3 stdin=serial stdout=serial stderr=serial
Sieht jetzt so aus:
Code:Board: STb7200-HDBOX [29-bit mode] U-Boot 1.3.1 (Apr 28 2010 - 15:01:04) - stm23-0032 ---created by TDT for general purpose--- DRAM: 128 MB Flash: 32 MB In: serial Out: serial Err: serial Frontpanel got PowerOn reset... init Frontpanel... done, AV7000 Hit any key to stop autoboot: 1 0 bootmenu_timeout:3000,default:3 add entry:0 - ---Flash--- add entry:1 - --USB1 P1-- add entry:2 - --USB1 P2-- add entry:3 - --USB1 P3-- add entry:4 - --USB1 P4-- add entry:5 - --USB2 P1-- add entry:6 - --USB2 P2-- add entry:7 - --USB2 P3-- add entry:8 - --USB2 P4-- add entry:9 - --USB 112-- entering bootmenu - default:3 - --USB1 P3-- selected: --USB1 P2-- USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found reading /uImage2 ** Unable to read "/uImage2" from usb 0:1 ** loading from usb 0:2 1898081 bytes read ## Booting image at a5000000 ... Image Name: Linux-2.6.32.61_stm24_0215 Image Type: SuperH Linux Kernel Image (gzip compressed) Data Size: 1898017 Bytes = 1.8 MB Load Address: 84001000 Entry Point: 84002000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel console=ttyAS0,115200 nwhwconf=device:eth0,hwaddr:00:1E:B8:01:3C:0A ip=192.168.178.28::192.168.178.1:255.255.255.0:Twin:eth0:off root=/dev/sdb2 rw mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=5 init=/bin/dev - 0x00000000 - 0 ...
Nö, leider nicht.
Ist wegen der externen Platte (eSata) irgendwas zu beachten? Die benötige ich schon.
Habe gerade mal gecheckt was beim dontcry kommt. Ist auch nicht mehr, obwohl es startet. Falsche Einstellung im Putty möglich?
Geändert von mb04fwe3 (05.02.2015 um 14:04 Uhr)