Habe nochmal das gleiche Image ohne erfolg getestet und werde nun einmal ein älteres probieren.

by dontcry gibt es nun auch mehr infos output:
Code:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.02.06 09:07:38 =~=~=~=~=~=~=~=~=~=~=~= *


Board: STb7200-HDBOX  [29-bit mode]




U-Boot 1.3.1 (Apr 28 2010 - 15:01:04) - stm23-0032
---created by TDT for general purpose---


DRAM:  128 MB
Flash:   32 MB
In:    serial
Out:   serial
Err:   serial
Frontpanel got PowerOn reset...
init Frontpanel... done, AV7000
Hit any key to stop autoboot:  1  0 
bootmenu_timeout:3000,default:3
add entry:0 - ---Flash---
add entry:1 - --USB1 P1--
add entry:2 - --USB1 P2--
add entry:3 - --USB1 P3--
add entry:4 - --USB1 P4--
add entry:5 - --USB2 P1--
add entry:6 - --USB2 P2--
add entry:7 - --USB2 P3--
add entry:8 - --USB2 P4--
add entry:9 - --USB 112--
entering bootmenu - default:3 - --USB1 P3--
USB:   scanning bus for devices... 3 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage3


** Unable to read "/uImage3" from usb 0:1 **
loading from usb 0:3


1916143 bytes read
## Booting image at a5000000 ...
   Image Name:   Linux-2.6.32.28_stm24_0207
   Image Type:   SuperH Linux Kernel Image (gzip compressed)
   Data Size:    1916079 Bytes =  1.8 MB
   Load Address: 84001000
   Entry Point:  84002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK


Starting kernel console=ttyAS1,115200 nwhwconf=device:eth0,hwaddr:00:1E:B8:01:3C:0A ip=192.168.178.28::192.168.178.1:255.255.255.0:Twin:eth0:off root=/dev/sdb3 rw mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=5 init=/bin/dev - 0x00000000 - 0 ...




INIT: version 2.86 booting




INIT: Entering runlevel: 3


[rcS] start /etc/init.d/rcS


INIT: no more processes left in this runlevel


[rcS] booting AAF_M15000_r3650_at7000_enigma2
Mount /dev in tmpfs
Copying device nodes to /dev
[rcS] start start.sh first enigma2 at7000
[start.sh] [first] startConfig
[start.sh] Thread 1 start
shared mem created
[start.sh] [first] init stmfb
[start.sh] [first] startTimeset
Sat Dec 12 20:00:00 CET 1970
[/var/etc/autostart/start.sh] start inetd
[set_was_timer_wakeup] checkConfig
[set_was_timer_wakeup] configs: WAKEUPDECREMENT  300
[start.sh] [first] enable HDMI
[start.sh] [first] startBootlogo 
[start.sh] [first] startVfd
[bootlogo.sh] start /var/etc/boot/bootlogo.sh
[start.sh] [first] current Date : 20:00:00 12-12-1970
[bootlogo.sh] use bootlogo jpg
/bin/fp_control: SW Version 1.02
Model: hdbox
vBoxType: 7
Selected Model: Fortis HDBOX frontpanel control utility
cannot open /dev/vfd
No such device or address
checkConfig
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM =     %H:%M:%S    
, WAKEUPDECREMENT  300
getTimeFromArg
getTimeFromArg <
Set Time (UTC): 19:00:00 12-12-1970
settime: : Bad file descriptor
[start.sh] Thread 1 end
*** InfoBox v1.7 by GOst4711 and nit ***
1280x720, 32bpp
[start.sh] [first] startFrontpanel
[start.sh] [first] init frontpanel
[start.sh] [first] startEvremote enigma2 at7000
MaxRate= 10
MaxDelay= 120
[/var/etc/autostart/start.sh] start autofs
Model: hdbox
vBoxType: 7
Input device name: "TDT RC event driver"
Selected Remote: Fortis HDBOX RemoteControl
RemoteControl Map:
                MENU - 04 - 139
                 RED - 4B - 398
               GREEN - 4A - 399
              YELLOW - 49 - 400
                BLUE - 48 - 401
                EXIT - 1C - 102
                TEXT - 0D - 388
                 EPG - 08 - 365
              REWIND - 58 - 168
         FASTFORWARD - 5C - 208
                PLAY - 55 - 207
               PAUSE - 07 - 119
              RECORD - 56 - 167
                STOP - 54 - 128
             STANDBY - 0A - 116
                MUTE - 0C - 113
           CHANNELUP - 5E - 104
         CHANNELDOWN - 5F - 109
            VOLUMEUP - 4E - 115
          VOLUMEDOWN - 4F - 114
                INFO - 06 - 138
                  OK - 1F - 352
                  UP - 00 - 103
               RIGHT - 02 - 106
                DOWN - 01 - 108
                LEFT - 03 - 105
              RECALL - 09 - 396
                ZOOM - 0B - 372
             VFORMAT - 0E - 371
          RESOLUTION - 0F - 375
             TVRADIO - 1A - 373
               SLEEP - 1E - 409
                OPEN - 40 - 394
                 FAV - 41 - 364
               CHECK - 42 - 353
                UPUP - 43 - 414
            DOWNDOWN - 44 - 415
                NEXT - 4C - 407
                LAST - 50 - 412
                 PIP - 51 - 357
                SWAP - 52 - 354
                LIST - 53 - 370
             0BUTTON - 10 -  11
             1BUTTON - 11 -   2
             2BUTTON - 12 -   3
             3BUTTON - 13 -   4
             4BUTTON - 14 -   5
rm: can't remove '/media/net/*': No such file or directory
             5BUTTON - 15 -   6
             6BUTTON - 16 -   7
             7BUTTON - 17 -   8
             8BUTTON - 18 -   9
             9BUTTON - 19 -  10
Frontpanel Map:
             STANDBY - 00 - 116
                  OK - 06 - 352
                MENU - 05 - 139
            VOLUMEUP - 04 - 115
          VOLUMEDOWN - 03 - 114
           CHANNELUP - 01 - 104
         CHANNELDOWN - 02 - 109
Supports Long KeyPress: 1
processComplex >
period 10, delay 120
Using period=10 delay=120
[SEM] DOWN
[/var/etc/autostart/start.sh] start load autofs
jpg image hight = 720
jpg image width = 1280
[/var/etc/autostart/start.sh] start hotplug.sh first enigma2 at7000
[/var/etc/autostart/start.sh] startNetwork: start
[start.sh] [first] startAvs
[start.sh] [first] load audio firmware (/boot/audio.elf)
copLoadFile (file /boot/audio.elf)
[networking] start eth0...
ustslave: Kernel Version: 24
base_address 0x10400000
seeking to 0
seeking to 5f00
seeking to 12320
[networking] eth0 using static ip
seeking to 1aa20
seeking to 173100
seeking to 173138
seeking to 173170
seeking to 1b9058
seeking to 1b9060
seeking to 1b9068
seeking to 1b9070
seeking to 1d0920
seeking to 1d0a00
[start.sh] [first] load video firmware
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x10000000
seeking to 0
seeking to 4e020
seeking to f8378
seeking to f83b0
seeking to f83e8
seeking to 10ce98
seeking to 10cea4
seeking to 10ceb0
seeking to 12ed90
seeking to 12cd74
seeking to 12ee00
[start.sh] [first] init embx
[start.sh] [first] init player 191
[hotplug.sh] startNewdev device=sda1 label= type=jfs
[hotplug.sh] startChangedev device=sda1 label=NONLABEL-sda1 type=jfs
[hotplug.sh] startCheckdev device=sda1 label=NONLABEL-sda1 type=jfs
ls: /media/autofs/sda1: No such file or directory
[hotplug.sh] startCheckdev can not mount device=sda1 label=NONLABEL-sda1 type=jfs
[hotplug.sh] startRepairdev device=sda1
[start.sh] [first] startBootlogo cont
[start.sh] [first] startReader enigma2 at7000
[start.sh] Thread 2 start
[start.sh] [first] startPowerLed
fp_control: SW Version 1.02
Model: hdbox
vBoxType: 7
Selected Model: Fortis HDBOX frontpanel control utility
checkConfig
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM =     %H:%M:%S    
, WAKEUPDECREMENT  300
sh: write error: Input/output error
sh: write error: Input/output error
sh: write error: Input/output error
sh: write error: Input/output error
[start.sh] Thread 2 end
ls: /media/autofs/sda1: No such file or directory
killall: szap: no process killed
killall: enigma2: no process killed
*** InfoBox v1.7 by GOst4711 and nit ***
1280x720, 32bpp
160 - OK
****        10428 1 ****
[SEM] UP
KEY_PRESS - 160 1
++++            2 ms ++++
160 - OK
****           52 1 ****
++++           79 ms ++++
KEY_RELEASE - 160 00 1 1 CAUSE=Timeout
----          132 ms ----
[SEM] DOWN
------- Programmende
[/sbin/hotplug.sh] startFsck parameter1=sda1 parameter2=
umount: can't umount /dev/sda1: Invalid argument
/sbin/jfs_fsck version 1.1.15, 04-Mar-2011
processing started: 12/12/1970 20:00:13
The current device is:  /dev/sda1
Block size in bytes:  4096
Filesystem size in blocks:  156282624
**Phase 0 - Replay Journal Log
|........
.|.......
..|......
[/var/etc/autostart/start.sh] startWaitfor timed out: maxwaittime=10 sec waitfor=/tmp/.hotplugready
...|.....
....|....
.....|...
......|..
.......|.
Filesystem is clean.
killall: szap: no process killed
killall: enigma2: no process killed
add /dev/ttyUSB0
ls: /dev/ttyUSB0: No such file or directory
add /dev/ttyUSB1
ls: /dev/ttyUSB1: No such file or directory
[hotplug.sh] startIsreadonly device=sda1 label=NONLABEL-sda1 type=jfs
[hotplug.sh] startNewdev found movie device=sda1 label=NONLABEL-sda1 type=jfs
[hotplug.sh] startNewdev device=sdb1 label=MINI1 type=jfs
[hotplug.sh] startChangedev device=sdb1 label=MINI1-sdb1 type=jfs
[rcS] starting enigma2
[FREESAT] Init tables
setenv('prefix', '/usr', 0)
setenv('exec_prefix', '${prefix}', 0)
setenv('bindir', '${exec_prefix}/bin', 0)
setenv('sbindir', '${exec_prefix}/sbin', 0)
setenv('libexecdir', '${exec_prefix}/libexec', 0)
setenv('datarootdir', '${prefix}/share', 0)
setenv('datadir', '/usr/local/share', 0)
setenv('sysconfdir', '/etc', 0)
setenv('sharedstatedir', '${prefix}/com', 0)
setenv('localstatedir', '${prefix}/var', 0)
setenv('libdir', '${exec_prefix}/lib', 0)
setenv('localedir', '${datarootdir}/locale', 0)
setenv('prefix', '/usr', 1)
setenv('exec_prefix', '/usr', 1)
setenv('bindir', '/usr/bin', 1)
setenv('sbindir', '/usr/sbin', 1)
setenv('libexecdir', '/usr/libexec', 1)
setenv('datarootdir', '/usr/share', 1)
setenv('datadir', '/usr/local/share', 1)
setenv('sysconfdir', '/etc', 1)
setenv('sharedstatedir', '/usr/com', 1)
setenv('localstatedir', '/usr/var', 1)
setenv('libdir', '/usr/lib', 1)
setenv('localedir', '/usr/share/locale', 1)
resolve: resolve ${datadir}/enigma2/encoding.conf
resolve: -> /usr/local/share/enigma2/encoding.conf
resolve: resolve ${libdir}/enigma2/python
resolve: -> /usr/lib/enigma2/python
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (8) graphics acceleration manager
STMFB accel interface available


+ (9) GFBDC
15360k video mem
5640kB available for acceleration surfaces.
resolution: 720 x 576 x 32 (stride: 5120)
+ (9) gLCDDC
couldn't open LCD - load lcd.o!
lcd buffer 0x653510 8448 bytes, stride 132
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
eDVBCI_UI >
eDVBCI_UI <
+ (20) UHF Modulator
couldnt open /dev/rfmod0!!!!
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "TDT RC event driver" is not a keyboard.
failed to open /dev/input/event1
Input device "" is not a keyboard.
failed to open /dev/input/event2
Input device "" is not a keyboard.
failed to open /dev/input/event3
Input device "" is not a keyboard.
Found 4 input devices!
+ (21) Console RC Driver
failed to open /dev/tty0
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
CI Slot 0: reset requested
deleteSessions >
deleteSessions <
CI Slot 1: reset requested
deleteSessions >
deleteSessions <
stat on /dev/dvb/adapter0/ci2 failed


CI Slot 0 setSource(0)
CI Slot 1 setSource(0)
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
cannot open /proc/stb/tsmux/input2
cannot open /proc/stb/tsmux/input3
done, found 2 common interface slots
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
resolve: resolve ${sysconfdir}/enigma2/lamedb
resolve: -> /etc/enigma2/lamedb
---- opening lame channel db
reading services (version 4)
[hotplug.sh] startNewdev device=sdb2 label=MINI2 type=ext2
[hotplug.sh] startChangedev device=sdb2 label=MINI2-sdb2 type=ext2
[hotplug.sh] startNewdev device=sdb3 label=MINI3 type=ext2
[hotplug.sh] startChangedev device=sdb3 label=MINI3-sdb3 type=ext2
loaded 2023 services
scanning for frontends..
opening frontend 0
[hotplug.sh] startNewdev device=sdb4 label=SWAP type=vfat
[hotplug.sh] startChangedev device=sdb4 label=SWAP-sdb4 type=vfat
detected satellite frontend
FE_ENABLE_HIGH_LNB_VOLTAGE: Operation not supported
close frontend 0
FE_ENABLE_HIGH_LNB_VOLTAGE: Operation not supported
opening frontend 1
detected satellite frontend
FE_ENABLE_HIGH_LNB_VOLTAGE: Operation not supported
close frontend 1
FE_ENABLE_HIGH_LNB_VOLTAGE: Operation not supported
found 1 adapter, 2 frontends(2 sim) and 3 demux, boxtype 11
RTC not ready... wait for transponder time
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
resolve: resolve ${datadir}/enigma2/skin_default/pal.png
resolve: -> /usr/local/share/enigma2/skin_default/pal.png


/dev/sda:
hdparm: BLKRRPART: Device or resource busy
Loading spinners...
resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait1.png
resolve: -> /usr/local/share/enigma2/skin_default/spinner/wait1.png


/dev/sdb:
hdparm: BLKRRPART: Device or resource busy
resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait2.png
resolve: -> /usr/local/share/enigma2/skin_default/spinner/wait2.png
hdparm: can't open '/dev/sdc': No such device or address
resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait3.png
resolve: -> /usr/local/share/enigma2/skin_default/spinner/wait3.png
resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait4.png
resolve: -> /usr/local/share/enigma2/skin_default/spinner/wait4.png
hdparm: can't open '/dev/sdd': No such device or address
resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait5.png
resolve: -> /usr/local/share/enigma2/skin_default/spinner/wait5.png
resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait6.png
resolve: -> /usr/local/share/enigma2/skin_default/spinner/wait6.png
resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait7.png
resolve: -> /usr/local/share/enigma2/skin_default/spinner/wait7.png
resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait8.png
resolve: -> /usr/local/share/enigma2/skin_default/spinner/wait8.png
found 7 spinner!


executing main
setIoPrio best-effort level 3 ok
resolve: resolve ${libdir}/enigma2/python/mytest.py
resolve: -> /usr/lib/enigma2/python/mytest.py
resolve: resolve ${sysconfdir}/
resolve: -> /etc/
resolve: resolve ${sysconfdir}/
resolve: -> /etc/
resolve: resolve ${datadir}/fonts/
resolve: -> /usr/local/share/fonts/
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
resolve: resolve ${libdir}/enigma2/python/Plugins/
resolve: -> /usr/lib/enigma2/python/Plugins/
resolve: resolve ${datadir}/enigma2/po/
resolve: -> /usr/local/share/enigma2/po/
resolve: resolve ${datadir}/enigma2/
resolve: -> /usr/local/share/enigma2/
resolve: resolve ${datadir}/enigma2/
resolve: -> /usr/local/share/enigma2/
resolve: resolve ${sysconfdir}/enigma2/playlist/
resolve: -> /etc/enigma2/playlist/
resolve: resolve ${datadir}/enigma2/defaults/
resolve: -> /usr/local/share/enigma2/defaults/
resolve: resolve ${datadir}/enigma2/dealer
resolve: -> /usr/local/share/enigma2/dealer
resolve: resolve ${datadir}/meta
resolve: -> /usr/local/share/meta
resolve: resolve ${datadir}/enigma2/defaults/
resolve: -> /usr/local/share/enigma2/defaults/
couldn't open fp
enumerating block devices...
enumerateBlockDevices 1 blockdev loop0
found block device 'loop0': blacklisted
enumerateBlockDevices 1 blockdev loop1
found block device 'loop1': blacklisted
enumerateBlockDevices 1 blockdev loop2
found block device 'loop2': blacklisted
enumerateBlockDevices 1 blockdev loop3
found block device 'loop3': blacklisted
enumerateBlockDevices 1 blockdev loop4
found block device 'loop4': blacklisted
enumerateBlockDevices 1 blockdev loop5
found block device 'loop5': blacklisted
enumerateBlockDevices 1 blockdev loop6
found block device 'loop6': blacklisted
enumerateBlockDevices 1 blockdev loop7
found block device 'loop7': blacklisted
enumerateBlockDevices 1 blockdev mtdblock0
found block device 'mtdblock0': blacklisted
enumerateBlockDevices 1 blockdev mtdblock1
found block device 'mtdblock1': blacklisted
enumerateBlockDevices 1 blockdev mtdblock2
found block device 'mtdblock2': blacklisted
enumerateBlockDevices 1 blockdev mtdblock3
found block device 'mtdblock3': blacklisted
enumerateBlockDevices 1 blockdev mtdblock4
found block device 'mtdblock4': blacklisted
enumerateBlockDevices 1 blockdev mtdblock5
found block device 'mtdblock5': blacklisted
enumerateBlockDevices 1 blockdev sda
found block device 'sda': ok, removable=False, cdrom=False, partitions=['sda1']
[Harddisk] found:  /sys/devices/platform/sata-stm/host0/target0:0:0/0:0:0:0
new Harddisk sda -> /dev/sda -> /dev/sda
[ePopen] command: ('hdparm', 'hdparm', '-S0', '/dev/sda')
enumerateBlockDevices 2 part: sda1
[Harddisk] found: sda1
found block device 'sda1': error querying properties
enumerateBlockDevices 1 blockdev sdb
found block device 'sdb': ok, removable=True, cdrom=False, partitions=['sdb1', 'sdb2', 'sdb3', 'sdb4']
enumerateBlockDevices 2 part: sdb1
[Harddisk] found: sdb1
found block device 'sdb1': error querying properties
enumerateBlockDevices 2 part: sdb2
[Harddisk] found: sdb2
found block device 'sdb2': error querying properties
enumerateBlockDevices 2 part: sdb3
[Harddisk] found: sdb3
found block device 'sdb3': error querying properties
enumerateBlockDevices 2 part: sdb4
[Harddisk] found: sdb4
found block device 'sdb4': error querying properties
[harddisk] AutoFS add: NETFS (smbfs) smbfs    -fstype=smbfs,allow_other,nonempty    :/media/smbfs


[harddisk] AutoFS add: NETFS (upnpfs) upnpfs    -fstype=upnpfs,allow_other,nonempty    :/media/upnpfs


[harddisk] AutoFS skip: ERROR (sda1)
[harddisk] AutoFS skip: ERROR (sdb1)
[harddisk] AutoFS skip: ERROR (sdb2)
[harddisk] AutoFS skip: ERROR (sdb3)
[harddisk] AutoFS skip: ERROR (sdb4)
Preferred tag editor set to  None
[standby] boxversion at7000
Reading satellites.xml
resolve: resolve ${datadir}/enigma2/unicable.xml
resolve: -> /usr/local/share/enigma2/unicable.xml
sec config cleared
setSlotInfo for dvb frontend 0 to slotid 0, descr STV090x Multistandard, need rotorworkaround No, enabled Yes, DVB-S2 Yes
setSlotInfo for dvb frontend 1 to slotid 1, descr STV090x Multistandard, need rotorworkaround No, enabled Yes, DVB-S2 Yes
slot: 0 configmode: simple
diseqcmode:  diseqc_a_b_c_d
slot: 1 configmode: equal
sec config completed
resolve: resolve ${datadir}/enigma2/setup.xml
resolve: -> /usr/local/share/enigma2/setup.xml
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/bouquets.tv
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/userbouquet.favourites.tv
54 entries in Bouquet userbouquet.favourites.tv
1 entries in Bouquet bouquets.tv
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/bouquets.radio
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/userbouquet.dbe02.radio
13 entries in Bouquet userbouquet.dbe02.radio
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/userbouquet.favourites.radio
0 entries in Bouquet userbouquet.favourites.radio
2 entries in Bouquet bouquets.radio
[eDVBLocalTimeHandler] enable sync local time with transponder time!
/usr/lib/python2.6/site-packages/twisted/internet/_sslverify.py:5: DeprecationWarning: the md5 module is deprecated; use hashlib instead
add dreampackage scanner plugin
added
4956kB available for acceleration surfaces.
resolution: 1024 x 576 x 32 (stride: 5120)
[FONT] adding font /usr/local/share/fonts/default.ttf...OK (Regular)
[FONT] adding font /usr/local/share/fonts/Symbols.ttf...OK (Symbols)
[FONT] adding font /usr/local/share/fonts/tuxtxt.ttf...OK (Console)
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/event1' >
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js0' >
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/event3' >
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 22] Invalid argument >
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js3' >
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 25] Inappropriate ioctl for device >
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse3' >
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/event2' >
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse0' >
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse2' >
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js1' >
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/mouse1' >
[iInputDevices] getInputDevices  <ERROR: ioctl(EVIOCGNAME): [Errno 19] No such device: '/dev/input/js2' >
resolve: resolve ${datadir}/enigma2/keymap.xml
resolve: -> /usr/local/share/enigma2/keymap.xml
[ePopen] command: ip -o addr show dev eth0
resolve: resolve ${datadir}/keymaps/
resolve: -> /usr/local/share/keymaps/
Activating keymap: Keyboard English
resolve: resolve ${datadir}/keymaps/
resolve: -> /usr/local/share/keymaps/
Activating language German
language set to de_DE
[VFD-Icons] BOXVERSION = at7000
--> applying pep values
couldn't apply pep values.
getModeList for port Component
getModeList for port Scart
getModeList for port HDMI
getModeList for port HDMI-PC
hotplug on dvi
-> setting aspect, policy, policy2, wss 16:9 bestfit letterbox auto(4:3_off)
-> setting aspect, policy, policy2, wss 16:9 bestfit letterbox auto(4:3_off)
-> setting aspect, policy, policy2, wss 16:9 bestfit letterbox auto(4:3_off)
-> setting aspect, policy, policy2, wss 16:9 bestfit letterbox auto(4:3_off)
setMode - port: HDMI mode: 1080p rate: 24Hz
-> setting aspect, policy, policy2, wss 16:9 bestfit letterbox auto(4:3_off)
updateColor:  HDMI
Plugins
[WebInterface] set language to  de
[WebInterface] set language to  de
/usr/lib/python2.6/site-packages/twisted/python/filepath.py:12: DeprecationWarning: the sha module is deprecated; use the hashlib module instead
[WebInterface] fallback to default translation for Webinterface
[eSocketMMIHandler] created successfully
[PLUGLOAD] Python searchpath:  ['/usr/lib/enigma2/python', '/usr/lib/python26.zip', '/usr/lib/python2.6', '/usr/lib/python2.6/plat-linux2', '/usr/lib/python2.6/lib-tk', '/usr/lib/python2.6/lib-old', '/usr/lib/python2.6/lib-dynload', '/usr/lib/python2.6/site-packages', '/var/swap/python2.6', '/var/swap/python2.6/site-packages']
It's now  Sat Dec 12 20:00:50 1970
[timer.py] next activation: 29876550 (in 99719 ms)
[EPGRefresh] fallback to default translation for Automated EPGRefresher
[EPGRefresh] fallback to default translation for Automated EPGRefresher
[EPGRefresh] fallback to default translation for Add to EPGRefresh
[Aaf-Panel] boxversion: at7000 ImageType: Usb
boxversion at7000
starting hotplug handler
...
...
...
It's now  Sat Dec 12 20:00:55 1970
[timer.py] next activation: 29876555 (in 99887 ms)
Repeated: 1
Repeated: 3
Repeated: 7
Repeated: 15
Repeated: 31
Repeated: 63
Repeated: 127
ProcessRepeated
localrepeatedbegindate: Sat Dec 12 04:15:00 2009
localbegin: Sat Dec 12 04:15:00 2009
localend: Sat Dec 12 04:15:00 2009
localnow: Sat Dec 12 20:00:56 1970
Day: 0
Day: 1
Day: 2
Day: 3
Day: 4
Day: 5
Day: 6
ProcessRepeated result
Sat Dec 12 04:15:00 2009
Sat Dec 12 04:15:01 2009
It's now  Sat Dec 12 20:00:55 1970
next real activation is Sat Dec 12 04:15:01 2009
[timer.py] next activation: 29876555 (in 99793 ms)
[EPGC] setCacheFile read/write epg data from/to '/media/autofs/sdb4/epg.dat'
not showing fine-tuning wizard, config variable doesn't exist
showtestcard is false
Looking for embedded skin
warning, skin is missing element VolumeText in <class 'Screens.Volume.Volume'>
setValue 45
[showMute]
Setvolume: 45 45 (raw)
Setvolume: 35 35 (-1db)
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
reused converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
reused converter!
RemovePopup, id = ZapError
warning, skin is missing element VolumeText in <class 'Screens.Volume.Volume'>
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
allocating new converter!
reused converter!
allocating new converter!
resolve: resolve ${datadir}/enigma2/%s/
resolve: -> /usr/local/share/enigma2/%s/
reused converter!
allocating new converter!
playing 1:0:1:6D66:437:1:C00000:0:0:0:
[VFD-Icons] __evSeekableStatusChanged
[VFD-Icons] showTimeShift
[VFD-Icons] Timeshift disabled
[VFD-Icons] __getSeekState
not pauseable.
RemovePopup, id = ZapError
allocate channel.. 0437:0001
opening frontend 0
FE_ENABLE_HIGH_LNB_VOLTAGE: Operation not supported
[eDVBCAService] new channel 0x123f6d8!
(0)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 0 Freq 11953500 Pol 0 SR 27500000 INV 2 FEC 3 orbpos 192 system 0 modulation 1 pilot 2, rolloff 0
tuning to 1353 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:1:6D66:437:1:C00000:0:0:0:
allocate demux
resolve: resolve ${sysconfdir}/scan_tp_valid_check.py
resolve: -> /etc/scan_tp_valid_check.py
set sequence pos 3
set sequence pos 4
[SEC] setVoltage 2
FE_ENABLE_HIGH_LNB_VOLTAGE: Operation not supported
[SEC] sleep 200ms
child has terminated
pipes closed
------- Programmende
[ePopen] command: route -n | grep  eth0
child has terminated
pipes closed
poll: unhandled POLLERR/HUP/NVAL for fd 27(16)
poll: unhandled POLLERR/HUP/NVAL for fd 29(16)
child has terminated
pipes closed
poll: unhandled POLLERR/HUP/NVAL for fd 36(16)
[SEC] invalidate current switch params
[SEC] sendDiseqc: e00000(DiSEqC reset)
[SEC] sleep 50ms
child has terminated
pipes closed
192.168
0.0.0.0
nameservers: [[192, 168, 178, 1]]
read configured interface: {'lo': {'dhcp': False}, 'eth0': {'dhcp': False, 'netmask': [255, 255, 255, 0], 'gateway': [192, 168, 178, 1], 'address': [192, 168, 178, 180]}}
self.ifaces after loading: {'eth0': {'preup': False, 'predown': False, 'ip': [192, 168, 178, 180], 'up': True, 'mac': '00:1e:b8:01:3c:0a', 'dhcp': False, 'bcast': [192, 168, 178, 255], 'netmask': [255, 255, 255, 0], 'gateway': [192, 168, 178, 1]}}
[]
[Toplevel.importExternalModules] Imported external module: Example
[Toplevel.importExternalModules] Could NOT import external module: EPGRefresh
[Toplevel.importExternalModules] Exception Caught
Bad magic number in /usr/lib/enigma2/python/Plugins/Extensions/EPGRefresh/EPGRefreshResource.pyc
[Toplevel.importExternalModules] Could NOT import external module: AutoTimer
[Toplevel.importExternalModules] Exception Caught
Bad magic number in /usr/lib/enigma2/python/Plugins/Extensions/AutoTimer/AutoTimerResource.pyc
[Webinterface] started on 192.168.178.180:80 auth= False ssl= False
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[Webinterface] started on 127.0.0.1:80 auth= False ssl= False
[WebInterface.unregisterBonjourService] No module named Bonjour.Bonjour
poll: unhandled POLLERR/HUP/NVAL for fd 34(16)
[SEC] sendDiseqc: e00003(DiSEqC peripherial power on)
[SEC] sleep 150ms
[SEC] sendDiseqc: e01038f3
[SEC] sleep 50ms
set sequence pos 3
[SEC] setTone 1
[SEC] sleep 10ms
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 0
[SEC] sleep 500ms
(0)fe event: status 0, inversion off, m_tuning 1
(0)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBCAService] channel 0x123f6d8 running
[eDVBLocalTimerHandler] channel 0x123f6d8 running
no version filtering
0014:  70 00 00 00 00 00
mask:  fc 00 00 00 00 00
mode:  00 00 00 00 00 00
[eEPGCache] channel 0x123f6d8 running
stop release channel timer
no version filtering
0012:  4e 6d 66 00 00 00
mask:  ff ff ff 00 00 00
mode:  00 00 00 00 00 00
ok ... now we start!!
no version filtering
0000:  00 00 00 00 00 00
mask:  ff 00 00 00 00 00
mode:  00 00 00 00 00 00
eventNewProgramInfo 0 0
have 1 video stream(s) (006e), and 1 audio stream(s) (0078), and the pcr pid is 006e, and the text pid is 0082
allocate demux
disable teletext subtitles
decoder state: play, vpid=110, apid=120
DMX_SET_PES_FILTER(0x6e) - pcr - ok
DMX_SET_PES_FILTER(0x78) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 0 - ok
DMX_SET_PES_FILTER(0x6e) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x82) - ttx - ok
VIDEO_CONTINUE - ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
AUDIO_CHANNEL_SELECT(0) - ok
[VFD-Icons] __evUpdatedInfo
MPEG
[VFD-Icons] noRecords
[VFD-Icons] showCrypted
[VFD-Icons] showDolby
[VFD-Icons] showMp3
[VFD-Icons] showMute
[VFD-Icons] showTimer
[VFD-Icons] seekTimers Search Timers
[seekTimers] State = 0
[VFD-Icons] seekTimers Found timer
[VFD-Icons] showTuner
[VFD-Icons] showTuner TUNER 1
[Volume Adjust] Update Info
[Setvolume] start with volume 45
Setvolume: 45 45 (raw)
Setvolume: 35 35 (-1db)
[Volume Adjust] Volume = 45
[Volume Adjust] load xml...
[Volume Adjust] New Channel
[Volume Adjust] oldvol = 0
PlugLoad is loading Plugins
+ 1/1 TID 00
done!
PATready
use pmtpid 0064 for service_id 6d66
no version filtering
0064:  02 6d 66 00 00 00
mask:  ff ff ff 00 00 00
mode:  00 00 00 00 00 00
doing version filtering
0000:  00 00 00 01 00 00
mask:  ff 00 00 3f 00 00
mode:  00 00 00 3e 00 00
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
+ 1/1 TID 02
done!
eventNewProgramInfo 0 0
have 1 video stream(s) (006e), and 4 audio stream(s) (0078, 0079, 007a, 007d), and the pcr pid is 006e, and the text pid is 0082
decoder state: play, vpid=110, apid=120
[VFD-Icons] __evUpdatedInfo
MPEG
MPEG
MPEG
AC3
[VFD-Icons] noRecords
[VFD-Icons] showCrypted
[VFD-Icons] showDolby
[VFD-Icons] showMp3
[VFD-Icons] showMute
[VFD-Icons] showTimer
[VFD-Icons] seekTimers Search Timers
[seekTimers] State = 0
[VFD-Icons] seekTimers Found timer
[VFD-Icons] showTuner
[VFD-Icons] showTuner TUNER 1
[Volume Adjust] Update Info
[Volume Adjust] Volume = 45
[Volume Adjust] load xml...
[eDVBCAService] new service 1:0:1:6D66:437:1:C00000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:1:6D66:437:1:C00000:0:0:0:
[eDVBCIInterfaces] gotPMT
demux 0 mask 01 prevhash 00000000
doing version filtering
0064:  02 6d 66 01 00 00
mask:  ff ff ff 3f 00 00
mode:  00 00 00 3e 00 00
[eDVBLocalTimerHandler] dont have correction.. set Transponder Diff
[eDVBLocalTimerHandler] update RTC
[eDVBLocalTimerHandler] time update to 09:09:16
[eDVBLocalTimerHandler] m_time_difference is 1393333696
[eDVBLocalTimerHandler] set Linux Time
[EPGC] time updated.. start EPG Mainloop
before: 1
after: 1
[EPGC] No blacklist found
-+ 1/2 TID 4e
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 5
FE_GET_PROPERTY failed (Invalid argument)
sdt update done!
Plugins
++ 2/2 TID 4e
done!
[VFD-Icons] __evUpdatedEventInfo
doing version filtering
0012:  4e 6d 66 19 00 00
mask:  ff ff ff 3f 00 00
mode:  00 00 00 3e 00 00
VIDEO_GET_EVENT - ok
[WebInterface] fallback to default translation for Webinterface
[VFD-Icons] __evVideoSizeChanged
VIDEO_GET_EVENT - ok
[MediaCenter] LANGUAGE: de
[MediaCenter] LANGUAGE: de
rm: can't remove '/tmp/.imdbrunning': No such file or directory
[VirtualZap] fallback to default translation for Virtual (PiP) Zap
[EPGRefresh] fallback to default translation for Automated EPGRefresher
[EPGRefresh] fallback to default translation for Automated EPGRefresher
[EPGRefresh] fallback to default translation for Add to EPGRefresh
[CI_Assignment] activating ci configs:
[CI_Activate] FOUND 2 CI Slots 
resolve: resolve ${sysconfdir}/enigma2/ci
resolve: -> /etc/enigma2/ci
[CI_Activate_Config_CI0] no config file found
[CI_Activate_Config_CI0] error parsing xml...
resolve: resolve ${sysconfdir}/enigma2/ci
resolve: -> /etc/enigma2/ci
[CI_Activate_Config_CI1] no config file found
[CI_Activate_Config_CI1] error parsing xml...
[Webinterface] stopping interface on  192.168.178.180  with port 80
[Webinterface] stopping interface on  127.0.0.1  with port 80
[ePopen] command: /var/etc/autostart/start.sh last &
[Webinterface] started on 192.168.178.180:80 auth= False ssl= False
[WebInterface.registerBonjourService] No module named Bonjour.Bonjour
[Webinterface] started on 127.0.0.1:80 auth= False ssl= False
HOTPLUG connection!
hotplug: ACTION=add
complete ACTION=add
HOTPLUG connection lost!
hotplug: {'ACTION': 'add', 'X_E2_CDROM': '0', 'X_E2_REMOVABLE': '0', 'DEVPATH': '/devices/virtual/block/ramzswap0'}
found block device 'ramzswap0': blacklisted
[EPGC] 60766 events read from /media/autofs/sdb4/epg.dat
[EPGC] start cleanloop
[EPGC] stop cleanloop
[EPGC] 4269640 bytes for cache used
[EPGC] next update in 2 sec
[EPGC] start caching events(1423210172)
no ancillary data in audio stream... abort radiotext pes parser
[set_was_timer_wakeup] Current Time: 09:09:26 06-02-2015
[set_was_timer_wakeup] Wakup Time: 21:30:00 06-02-2015
[set_was_timer_wakeup] diff in sec=44434, maxdiff=300
[EPGC] abort non avail schedule other reading
[EPGC] abort non avail FreeSat schedule_other reading
[EPGC] abort non avail viasat reading
[EPGC] abort non avail mhw reading
child has terminated
pipes closed
poll: unhandled POLLERR/HUP/NVAL for fd 56(16)
[EPGC] nownext finished(1423210185)
aber auch hier steht doch am anfang:
Starting kernel ... root=/dev/sdb3 ...

also sdb und dennoch läuft es

- - - Aktualisiert - - -

HDMU_13068 mit dem gleichen Ergebnis, hängt mit dem selben Output wie die aktuelle HDMU Version.